Table of Contents
Advertisement
Available languages
Available languages
ENGLISH
PLAYBACK
10
• Switch on your amplifier or receiver.
• Set the TAPE MONITOR switch on your amplifier or
receiver to the TAPE position.
1. POWER
• Push the switch q to turn "ON" (
¢
NOTE :
• The display lights when the deck mechanism is
being initialized. The deck will not operated
during initialization.
2. EJECT
) button @7 to open the
• Press the eject (
5
cassette compartment.
3. Cassette compartment cover @8
• Load the cassette tape.
4. DOLBY NR switch @2
• For recordings made without Dolby NR, set to
"OFF".
• For recordings made with Dolby B NR, set to
"B".
• For recordings made with Dolby C NR, set to
"C".
5. REV. MODE switch @0
: To listen to one side only
: To listen to repeat playback of both side
6. OUTPUT switch !9
• Select "SEP." to output only the deck signals,
"MIX" to output the mixed deck and CD signals
from the MIX outputs.
) button @9
7. Play (
0
or
1
• Push the play button (The direction of playback is
indicated (
or
)).
0
1
✽ When playback is finished, press the stop (
button @9 .
✽ To restart the tape, press the play (
0
@9 .
CAUTION :
• If different types of Dolby Noise Reduction are
used for record and playback, playback response
will be adversely effected.
14
Music search system
The music search system detects blank sections
(lasting for at least 4 seconds) between selections in
order to locate the beginning of selections in the
) the power.
forward or reverse direction.
1. To advance from the current selection to the
beginning of the next selection (CUE) :
) button @9 simultaneously with
Press the play (
1
) button @9 . Press the play (
the fast forward (
7
button @9 simultaneously with the rewind (
button @9 .
The deck will skip the rest of the current selection
and automatically resume play from the beginning
of the next selection.
2. To repeat playback from the beginning of the
current selection (REVIEW) :
) button @9 simultaneously with
Press the play (
1
) button @9 . Press the play (
the rewind (
6
button @9 simultaneously with the fast forward
) button @9 .
(
7
The deck will rewind the tape to the beginning of
the current selection and automatically resume play
from that point.
This is very convenient for repeating playback of the
current selection.
Notes on Music Search Operation :
The search functions operates by detecting
comparatively long, blank sections approximately 4
to 5 seconds long, in between recorded selections.
Therefore, the system may not operate normally in
the following cases :
• Recordings with discontinuous speech or
conversation.
2
)
• Recordings with long periods of pianissimo
or
) button
(softly played music).
1
• Blank sections with a high level of noise.
• Blank sections shorter than 4 seconds.
• If noise-emitting appliances, such as electric
razors, drills, refrigerators, etc., are operated
nearby.
• REVIEW close to the beginning of the program or
CUE close to the ending.
RECORDING
11
• Switch on the source component (tuner, amplifier,
etc.).
• Set the TAPE MONITOR switch on your amplifier or
receiver to the SOURCE position.
NOTE :
• It is not possible to use both the BALANCED
INPUT and UNBALANCED INPUT jacks at the
same time. Use the input selected with the
INPUT SELECT switch.
0
)
1. POWER
6
)
• Push the switch q to turn "ON" (
NOTE :
• The display lights when the deck mechanism is
being initialized. The deck will not operated
during initialization.
2. EJECT
)
) button @7 to open the
0
• Press the eject (
5
cassette compartment.
3. Cassette compartment cover @8
• Make sure the erasure prevention tab has not
been removed from the cassette shell half.
4. DOLBY NR switch @2
• Select the Dolby NR type that suits the
recording.
5. REV. MODE switch @0
: To record on only one side
: To continuously record on both sides
6. INPUT switch @1
• Select the recording source.
) button @9
7. Rec/Rec mute (
4
• When pressed, the tape deck goes into the
record standby mode. The "
,
" will light. Initial
4
3
setting of recording levels should be made in the
record standby mode.
8. INPUT LEVEL control @6
• Used to set the recording level.
) button @9
9. Play (
or
0
1
• Recording starts when the play (
@9 for the direction indicated by the lighting tape
travel indicator (
0
or
1
) is pressed. If the other
) button @9 is pressed, the direction
play (
or
0
1
of tape travel changes.
The play (
0
or
1
) and the "
4
" indicator will light
during recording.
✽ When recording is finished, press the stop (
button @9 .
CAUTION :
In the recording mode, the variable speed mode
cannot be selected, and the mode is automatically
switched to the fixed speed mode.
Be careful not to erase important recordings by
mistake. Mis-erasing can be avoided by following
the two steps below :
1. If the play (
or
) while the "
0
1
tape will be recorded.
2. If the play (
0
or
1
) and rec/rec mute (
are pressed at the same time, the tape will be
recorded.
¢
) the power.
3. Performing the record pause or the stop
operation during recording will create a
discontinuous portion in the recording signal.
The previously recorded signal may remain after
erasure at this connecting portion. Also, a very
small amount of the end portion of the previous
song may be erased.
CAUTION :
• Do not turn off the power while the deck is
operating or being initialized. Doing so could
cause damage.
CAUTION :
• This set has a quick reverse function. When
recording on an already recorded tape, some of
the old recording at the beginning of the reverse
side of the tape is not erased, so erase it before
starting to record.
0
or
1
) button
2
)
" will light, the
4
4
) button
Hide quick links:
Advertisement
Table of Contents
