Panasonic BT-4LH310P Operating Instructions Manual page 40

Main Menu
(Continued)
Setting
SDI DISPLAY MODE [SDI DISPLAY MODE SINGLE] → [SDI DISPLAY MODE QUAD]
ZOOM MODE [ZOOM MODE OFF] → [ZOOM MODE ON]
ZOOM POSITION [ZOOM POSITION CENTER] → [ZOOM POSITION LT] → [ZOOM POSITION RT] →
[ZOOM POSITION RB] → [ZOOM POSITION LB]
PIXEL TO PIXEL [PIXEL TO PIXEL OFF] → [PIXEL TO PIXEL ON]
FRAME GRAB [FRAME GRAB OFF] → [FRAME GRAB ON]
DISPLAY SELECT The displayed items differ depending on the mode.
• When normal mode of QUAD mode
[ DISPLAY SELECT SDI1] → [DISPLAY SELECT SDI2] → [DISPLAY SELECT SDI3] →
• When PICTURE ASSIST mode of QUAD mode
[AREA2] → [AREA3] → [AREA4]
MULTI FUNCTION [MULTI FUNCTION OFF] → [MULTI FUNCTION ON]
PICTURE ASSIST [PICTURE ASSIST OFF] → [PICTURE ASSIST ON]
WFM LINE SELECT [SETTING]
AUDIO MUTE [AUDIO MUTE OFF] → [AUDIO MUTE ON]
LEVEL METER [METER OFF] → [METER 2CH/4CH/8CH]
TIME CODE [TC OFF] → [LTC/VTC/LUB/VUB/LTC+LUB/VTC+VUB]
CLOSED CAPTION The displayed items differ depending on the [CC TYPE] selection.
• When the [CC TYPE] setting is [CEA-608(708)]:
[CC OFF] → [CC1/2/3/4]
• When the [CC TYPE] setting is [CEA-708]:
[CC OFF] → [SRV1/2/3/4/5/6]
• When the [CC TYPE] setting is [OP-47]:
[CC OFF] → [OP-47]
MARKER [MARKER OFF] → [RATIO Aspect Marker Type and Area Marker Type]
Splits each of the RATIO/Aspect Marker Type/Area Marker Type into the two lines Aspect Marker 1 and
Aspect Marker 2, and displays the current setting values.
• RATIO
• Aspect Marker Type
• Area Marker Type
*
*
*
*
FRAME MARKER [FRAME MARKER OFF] → [FRAME MARKER ON]
OUTER LINE [OUTER LINE MARKER OFF] → [OUTER LINE MARKER ON]
MARKER
CROSS HATCH [CROSS HATCH OFF] → [CROSS HATCH LOW] → [CROSS HATCH HIGH]
FOCUS-IN-RED [FOCUS-IN-RED OFF] → [FOCUS-IN-RED RED/BLUE/MONO]
Y MAP [Y MAP OFF] → [Y MAP ON]
ZEBRA [ZEBRA OFF] → [ZEBRA INT.] → [ZEBRA EXT.] → [ZEBRA INT.+EXT.]
ZEBRA LEVEL [SETTING]
SCREEN SAVER [SCREEN SAVER OFF] → [SCREEN SAVER ON]
LUT [STANDARD] → [USER1] → [USER2] → [USER3]
<Note>
• [WHITE BALANCE] and [ZEBRA LEVEL] are switched to the adjustment mode with a <FUNCTION> button but the operating status
is not displayed.
• [/] indications (for example, [CC1/2/3/4]) vary depending on the menu setting.
40
[DISPLAY SELECT SDI4]
17:9/16:9
17:9/16:9/4:3/13:9/14:9/CNSCO 2.39/CNESCO 2.35/2:1/VISTA
95%/93%/90%/88%/80%/xx%
If an area marker is displayed when aspect marker is off, the aspect marker type is displayed.
1
xx% indicates an 80% to 100% USER setting.
2
yy%/zz% indicates the VAR setting when an 80% to 100% aspect ratio is specified.
3
hhhh/xxxx indicates the H direction setting when the area marker DOTLINE is specified, and vvvv/yyyy
4
indicates the V direction setting.
Display
/yy%/zz% /DOThhhh/xxxx/LINEvvvv/yyyy
* *
2 3
*
1
*
4