Denon AVR-4810 Owner's Manual page 87

Setting items
Tone Tone Control : Sets the tone control function ON and OFF.
Adjust the tonal quality of
• ON : Allow tone adjustment (treble, bass).
the sound.
• OFF : Playback without tone adjustment.
• This can be set when "Dynamic EQ" (vpage 83) is set to "OFF".
• The tone cannot be adjusted in the direct mode.
Bass : Adjust low frequency range (bass).
• –6dB ~ +6dB
This can be set when "Tone Control" is set to "ON".
Treble : Adjust high frequency range (treble).
• –6dB ~ +6dB
This can be set when "Tone Control" is set to "ON".
MultEQ XT : Corrects both time and frequency response problems in the
Audyssey Settings
Set MultEQ XT, Dynamic EQ listening area.
and Dynamic Volume. • Audyssey : Optimize the frequency response of all speakers.
• Audyssey Byp.L/R : Optimize frequency response of speakers except
NOTE
front L and R speakers.
If you have not performed
• Audyssey Flat : Optimize frequency response of all speakers to flat
Auto Setup, or if you change
response.
the speaker settings after
• Manual : Apply frequency response set with "Manual EQ" (vpage
performing Auto Setup, you
85).
may not be able to select
• OFF : Turn "MultEQ XT" equalizer off.
Dynamic EQ/Dynamic Volume,
and "Run Audyssey" may be
displayed. • "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
In this case, either perform selected after Audyssey Auto Setup has been performed. "Audyssey"
Audyssey Auto Setup over is automatically selected after performing Audyssey Auto Setup. "When
again or perform "Restore" "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, "
(vpage 37) to return to the lights.
settings after Audyssey Auto • After running Audyssey Auto Setup, if the Speaker Configuration,
Setup was run. Distance, Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only "
• If "Dynamic EQ" or "Dynamic Volume" is set to "ON" when "MultEQ
XT" is set to either "OFF" or "Manual" , "MultEQ XT" is automatically
set to "Audyssey" .
• You can also press
NOTE
• "MultEQ XT" and "Manual" cannot be selected when "EQ Customize"
is set to "Not Used" (vpage 44).
• When using headphones, "MultEQ XT" is set to "OFF".
Main remote control unit
operation buttons
Setting contents
" lights.
MULTEQ XT
on the main remote control unit to set.
:Displaying the menu
Cancel the menu
Setting items
Dynamic EQ : Solves the problem of deteriorating sound quality as
Audyssey Settings
volume is decreased by taking into account human perception and room
(Continued)
acoustics.
• ON : Use the Dynamic EQ equalizer.
• OFF : Do not use the Dynamic EQ equalizer.
• After performing "Audyssey Auto Setup", the "Dynamic EQ" setting
automatically becomes "ON".
• "
• When "MultEQ XT" is set to "OFF" or "Manual", "Dynamic EQ" is
automatically set to "OFF".
• If "Dynamic Volume" is set to "ON", "Dynamic EQ" is automatically
set to "ON".
• When you set "Dynamic EQ" to "ON", "Tone Control" is switched
"OFF".
• You can also press
set.
Audyssey Dynamic EQ™ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
"
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ ® XT to provide well-balanced sound for every listener
at any volume level.
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting contents
" is displayed when set to "ON".
DYNAMIC EQ
on the main remote control unit to
Dynamic EQ / Volume : OFF
Dynamic EQ : ON/Volume : OFF
"Green" "Red" "OFF" "Off"
About Dynamic EQ
:Return to previous menu
ENGLISH
See overleaf