Denon AVR-4810 Owner's Manual page 38

ENGLISH
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)
d Perform Audyssey Auto Setup
• Audyssey Auto Setup detects the presence of each speaker and
automatically calculates the speaker size, channel level, distance and
crossover frequency settings. In addition, acoustical distortions are
corrected within the listening area.
• When measuring begins, a test tone is output from each speaker.
• Position and connect all speakers before commencing Audyssey
Auto Setup.
STEP2 Speaker Detection
1
Select "Measure" and
then press ENTER .
STEP2 Speaker Detection
Please place the microphone at ear
height at main listening position.
q M easure the subwoofer
level
To stop measuring, select
b
Start measurement. Output large test tone during measuring
"Cancel" and then press
ENTER
.
When "Subwoofer" is set to "Skip" with "Channel Skip", this
b
measurement is not taken, and the process proceeds to "w
Measure each speaker".
w M easure each speaker
Once the measurements in step q are complete, the
b
measurements in step w start automatically.
The measuring channel changes depending on the setting of "Amp
b
Assign" (vpage 38 ~ 40) and "Channel Skip" (vpage 33).
When an error message is displayed, check "Error Messages" for
details (vpage 36).
e C heck the speaker detection results
When measuring ends, the speaker detection results are
displayed.
Select "Next → Measurement" and press
b
" STEP3 ".
Press u to select "Retry", and when you press
b
at the main listening position starts again.

Main remote control unit
operation buttons
STEP3 Measurement
2
Move
microphone
position
"Measure", and then
press
The measurement of the
2nd position starts.
To skip this step, select "Next → Calculation" and proceed to
b
STEP4 .
AUDYSSEY AUTO SETUP
3
Repeat
1 2 3 4 5 6
measuring positions
3 ~ 8.
Measure
When measurement of
position 8 is completed,
Enter Cancel
RETURN
a
finished."
displayed.
To skip this step, select "Next → Calculation" and proceed to
b
STEP4 .
Measure in at least 6 positions in and around the main listening
b
position. Even though you can complete measurement with at
least 6 positions, it is advisable to use more than 6 (a maximum
of 8 positions).
ENTER
to proceed to
ENTER
, measuring
:Displaying the menu
Cancel the menu
the setup
AUDYSSEY AUTO SETUP
to
STEP3 Measurement
Please place the microphone at ear
2, select
height at 2nd listening position.
ENTER . Measure
Next Calculation
Enter
Start measurement. Output large test tone during measuring
step 2,
AUDYSSEY AUTO SETUP
STEP3 Measurement
Please place the microphone at ear
height at 3rd listening position.
Measure
Retry
"Measurements
Next Calculation
message is Enter
Start measurement. Output large test tone during measuring
:Moves the cursor
(Up/Down/Left/Right)
STEP4 Calculation
4
On the STEP3
screen, select "Next
1 2 3 4 5 6
→ Calculation", and
then press ENTER .
Measuring results
are analyzed, and the
Cancel
RETURN
frequency response
of each speaker in
the listening room is
determined.
Analysis takes several minutes to complete. The time required for
b
this analysis depends on the number of speakers connected.
1 2 3 4 5 6
The more connected speakers there are, the longer it takes to
perform analysis.
STEP5 Check
5
On the STEP5
Cancel
RETURN
screen, press
ui
to select the item you
want to check, and
then press ENTER .
Speaker Config. Check
Distance Check
Channel Level Check
Crossover Freq. Check
b Subwoofers may measure a greater reported distance than
the actual distance due to added electrical delay common in
subwoofers.
6
Press to select the channel you want to check.
ui
The measurement result of each speaker is displayed.
If you want to check another item, press
b
Select "Next → Store" and press
b
:Confirm the setting
AUDYSSEY AUTO SETUP
STEP4 Calculation 1 2 3 4 5 6
Now calculating... Please wait.
50%
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
STEP5 Check
Check processing results.
To proceed, press "Next".
Spkr Config Check
Distance Check
Ch. Level Check
Crossover Check
Next Store
Enter Cancel
RETURN
Select item to check
RETURN
.
ENTER
to proceed to " STEP6 ".
:Return to previous menu