Playing An Ipod ® Connected Directly To The Avr-4810'S; Usb Port - Denon AVR-4810 Owner's Manual

ENGLISH
Playing Components
Symbols used to indicate buttons in this manual
Button located on both the main unit
and the remote control unit
Button only on the main unit
Button only on the remote control unit
ENTER <STATUS>
uio p
[ NET/USB]
[SEARCH]
uio p
ENTER
[SOURCE
SELECT]
(MAIN mode)
[iPod]
(MAIN mode)
[TUNER]
[SHIFT]
Sub remote control unit
When no control dock for iPod is connected, this operation is also
b
possible in the "iPod" mode.

Playing an iPod ® Connected Directly to
the AVR-4810's USB Port
BUTTON
• Music stored on an iPod can be played on the AVR-4810 when the
<BUTTON>
AVR-4810 and iPod are connected by USB cable.
[BUTTON]
• The AVR-4810 supports iPod (5th generation and later), iPod nano,
iPod classic, and iPod touch audio (it is not compatible with iPod
shuffle). However, some functions may be limited on certain
models.
• The operation may not work properly if the iPod's software is old. Be
sure to use the latest version of iPod software.
• With iPods, non-copyrighted material and material for which
duplication and playback is authorized by law can be duplicated and
played by individuals for their personal enjoyment. Infringement of
copyrights is prohibited by law.
• Note that DENON will accept no responsibility whatsoever for any
problems arising with the data on an iPod when using the AVR-4810
in conjunction with the iPod.
Listening to music on an iPod ®
1 Connect the iPod ® to the AVR-4810's USB port using
[ TUNER]
the USB cable included with the iPod (vpage 23

"USB Port").

2
[A ~ G]
Turn the AVR-4810 power on.
[TU ]
f
(vpage 27 "Turning the Power On")
[TU ]
d
3 [SOURCE SELECT]
Press
[MEMO]
Select menu, then select "
[MODE]
[BAND]
– GUI screen –
uio p
DENON's iPod
ENTER
Playlistes
[SOURCE
Artists
SELECT]
Albums
Songs
(MAIN mode)
Podcasts
Genres
[CHANNEL]
Composers
[TUNER]
(MAIN mode)
[1 ~ 8]
b When the iPod is connected directly to the USB port, menus under
"Music" are displayed.
If the screens above are not displayed, the iPod may not be
b
properly connected. Try connecting again.
b When no control dock for iPod is connected, this can also be
[iPod]
selected by pressing
4
b
5
b
to display the GUI Source
" (vpage 30).
[1/9]
Search
SEARCH
6
7
.
Set the main remote control unit to the "NET/USB"
mode (vpage 99 "Operating the Main Remote
Control Unit").
When no control dock for iPod is connected, this operation is also
possible in the "iPod" mode.
[SEARCH]
Press and hold it down for a 2 seconds or
more to select the display mode.
There are two modes for display the contents recorded on the
iPod.
Browse mode
:
This is the mode for displaying the iPod information on the GUI
screen to operate the iPod. In this mode, you cannot perform
operations directly on the iPod itself.
z With the AVR-4810's display, only English letters and numbers
and certain symbols can be displayed. Any characters that
cannot be displayed are replaced with ". (period)".
Remote mode
:
This is the mode for performing operations directly on the iPod
itself while watching the screen displayed on the iPod. In this
mode, the GUI screen is not displayed.
z "Remote iPod" is displayed on the AVR-4810's display.
The Remote mode is not supported on 5th generation iPods or
b
iPod nanos.
Display mode Browse mode
Audio file S
Playable
Picture file A
files
Movie file A
Main remote
control unit
S
Active
(AVR-4810)
buttons
iPod ®
A
z : Only the sound is played.
ui
Use to select the item, then press
select the file to be played.
Press ENTER or .
p
Playback starts.
Remote mode
S
A
z
A
S
S
ENTER
p
or to