Denon AVR-4810 Owner's Manual page 47

Setting items
HDMI Control Control
External devices can be • ON : Use HDMI control function
controlled from the AVR- • OFF : Do not use HDMI control function
4810 and the AVR-4810 can
When a device that is not compatible with the HDMI control function
be controlled from external
is connected, set "Control" to "OFF".
devices.
NOTE
• When "Control" is set to "ON", it consumes more standby power.
• Please consult the
• When not using this unit for a long period, we recommend that you
operating instructions for
POWER
press
each connected device to
• "HDMI Control" does not work when the power to the equipment is off.
check the settings.
Either power on or set to standby.
• Refer to "HDMI Control
Standby Source : Set the HDMI connector for HDMI signal input during
Function" (vpage 90) for
standby.
more information about the
• Last : Standby with last used input source during power on.
HDMI control function.
• HDMI1 / HDMI2 / HDMI3 / HDMI4 / HDMI5 / HDMI6 : The standby mode
• When the "Control"
is set at the input source assigned to the respective.
setting has been changed,
always turn off the power
This can be set when "Control" is set to "ON".
to the connecting devices
Control Monitor : Set the HDMI MONITOR terminal to output the HDMI
afterwards and then turn
control signal.
back on.
• Monitor 1 : Output from the MONITOR 1 terminal.
• Monitor 2 : Output from the MONITOR 2 terminal.
NOTE
The HDMI control function
This can be set when "Control" is set to "ON".
controls operations of a
Power Off Control : The power of the AVR-4810 and external device turn
TV that is compatible with
off together.
the HDMI control function.
• ON : Interlock.
Make sure that the TV and
• OFF : Do not interlock.
HDMI are connected when
you perform HDMI control.
This can be set when "Control" is set to "ON".
Main remote control unit
operation buttons
Setting contents
on the main unit to turn off the power.
:Displaying the menu
Cancel the menu
Making the Audio Settings (Audio Setup)
Make settings for audio playback.
Setting items
EXT. IN Setup Subwoofer Level : Set playback level of subwoofer signal input from the
Setup playback method for external input connector (EXT. IN).
analog signals inputted from • +15dB : This is the recommended level.
external input connectors • +10dB / +5dB / 0dB : Select the level according to the player being
(EXT. IN). used.
Setting : Select the method for setting the speakers used in the 2-channel
2ch Direct/Stereo
Make speaker settings for 2- direct and stereo playback modes.
channel mode playback. • Basic : The settings at "Speaker Setup" (vpage 40) are applied.
• Custom : Make separate settings for 2-channel.
Front : Set the front speaker size.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Configuration" – "Subwoofer" (vpage 40) is set to
"No", the setting is automatically set to "Large".
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
If "Speaker Configuration" – "Subwoofer" (vpage 40) is set to
"No", the setting is automatically set to "No". If the "Front" setting is
"Small", the setting is automatically "Yes".
SW Mode : Select low range signal to be reproduced by subwoofer.
• LFE : When the "2ch Direct/Stereo" – "Front" setting is set to "Large",
the LFE signal alone is output from the subwoofer. Also, when the "2ch
Direct/Stereo" – "Front" setting is set to "Small", the front channel low
range signal is added to the LFE signal output from the subwoofer.
• LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This can be set when "2ch Direct/Stereo" – "Subwoofer" is set to
"Yes".
:Moves the cursor
:Confirm the setting
(Up/Down/Left/Right)
ENGLISH
Making Detailed Settings (Manual Setup)
Default settings are underlined.
Setting contents
See overleaf

:Return to previous menu