Program Mode - Starter Settings; Special Door Lock/ Unlock Operations; Gas/ Diesel Mode; Rearm Output - Ultra Start 1500 SERIES Installation Manual

PROGRAM MODE - STARTER SETTINGS

Enter STARTER Program Mode - See Page 7 for details on entering program mode
Setting 1- Special Door Lock/ Unlock Operations
1 Chrysler / VW Re-Arm
2 GM Auto Re-Lock
3* Normal Operation
Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 2- Gas/ Diesel Mode-
1 Diesel Glow Plug
2 Timed Delay
3* Gas Mode operation
Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 3- Rearm Output-
1 Type 1
2 Type 2
3* Factory Re-arm
Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
1 30 Min Run Time
2 45 Min Run Time
3* 15 Min Run Time
Press the Program Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 5-Maximum Crank Time
1 10 Seconds
2 3 Seconds
3* 5 seconds
Press the Program Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 6- Starter Kill/ Bypass Module Output-
1 Active Starter Kill
2 Passive Starter Kill
3* Bypass Module
Press the Program Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
Setting 7- Safety Start Mode
1 Safety ON
2* Safety OFF
Press the Program Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.
1 Flash Unlock pulse before start and a lock pulse after start
2 Flashes Lock pulse after remote starter shuts off
3 Flashes No additional re-lock pulses
1 Flash W
2 Flashes Ignition ON for 10 seconds before engaging remote starter
3 Flashes Waits 2 seconds before engaging starter output
1 Flash Pulse after start and with lock
2 Flashes Pulse after start only
3 Flashes
1 Flash Remote Starter runs for 30min when activated
2 Flashes Remote Starter runs for 45min when activated
3 Flashes Remote Starter runs for 15 min when activated
1 Flash 10 sec Max time that starter will stay engaged
2 Flashes 3 sec Max time that starter will stay engaged
3 Flashes 5 sec Max time that starter will stay engaged
1 Flash On when locked, Before ignition and 2 seconds after ignition turns off.
2 Flashes Same as setting 1 but will arm 60sec after the ignition turns off.
3 Flashes Output before ignition. Stays on 2 seconds after ignition turns off.
1 Flash Must press the start button twice to remote start vehicle
2 Flashes Press the start button once to remote start vehicle.
PROGRAMMING
aits a Maximum of 3:20 second before starting.
0.75 second pulse with lock and after shutdown
9