1. Manuals
  2. Brands
  3. Ultra Start Manuals
  4. Remote Starter
  5. 1172 SERIES
  6. Installation manual

Ultra Start 1172 Series Installation Manual

Advanced remote starters & vehicle security systems
Hide thumbs Also See for 1172 Series:

Advertisement

Table of Contents

See also: Owner's Manual
REV.2007.11.14A
1172 SERIES
Advanced Remote Starters &
Vehicle Security Systems
TM
TM
INSTALLATION GUIDE
www.ultrastarters.com
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user's authority to operate
this devise.

Advertisement

Table of Contents
loading

Related Manuals for Ultra Start 1172 Series

Summary of Contents for Ultra Start 1172 Series

  • Page 1 REV.2007.11.14A 1172 SERIES Advanced Remote Starters & Vehicle Security Systems INSTALLATION GUIDE www.ultrastarters.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation.

  • Page 2: Table Of Contents

    1172 SERIES PAGE 2 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TABLE OF CONTENTS QUICK VIEW WIRING DIAGRAM............3-4 Connector Pin Configuration Antenna Connector Park Light Jumper QUICK VIEW PROGRAMMING..............5-9 Enter Program Mode System Reset Transmitter Programming Menu 1,2,3 & 4 Quick View...
  • Page 3 1172 SERIES PAGE 3 QUICK VIEW WIRE DIAGRAM INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT YELLOW OUTPUT TO ACTIVATE THE VEHICLES ACCESSORY CIRCUIT GREEN 12VOLT/ 30 AMP MAIN POWER INPUT 12VOLT/ 30 AMP MAIN POWER INPUT...
  • Page 4 1172 SERIES PAGE 4 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 QUICK VIEW WIRE DIAGRAM OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-) GREEN N/A* OUTPUT FOR VOLTAGE INVERTER* OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-) BLUE (-) WHILE RUNNING OUTPUT (BYPASS TURN ON) / STARTER DISABLE...

  • Page 5: Quick View Programming

    1172 SERIES PAGE 5 QUICK VIEW PROGRAMMING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch located on the antenna 1 time.
  • Page 6 OPTIONS SINGLE LOCK UNLOCK UNLOCK BLUE & GREEN DOOR LOCK / 0.25 SEC PULSES 3 SEC PULSES 0.1172 SEC PULSES (DOOR LOCK HARNESS) UNLOCK PULSES BLACK (-) ACCESSORY OUTPUT (-) START OUTPUT AUX OUTPUT 1 AUX CHANNEL (#) (9 PIN CONNECTOR)
  • Page 7 1172 SERIES PAGE 6 QUICK VIEW PROGRAMMING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE 3 - see page 21 for detailed instructions SETTING # SETTING OPTION 1 OPTION 2 OPTION 3 WIRE COLOR DESCRIPTION 1 CHIRP 2 CHIRPS...
  • Page 8 1172 SERIES PAGE 8 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 TACH / TACHLESS LEARNING TACH NOTES * If the vehicle does not have a starter wire a manual tach learn must be preformed. (See Page 8) ** If Tach does not learn check for proper connection on the starter wire, ignition wire and at the Tach connection.

  • Page 9: Auto Tach Learning

    1172 SERIES PAGE 9 TACH / TACHLESS LEARNING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 AUTO TACH/ TACHLESS LEARNING 2 CHIRPS Horn will chip to confirm that Start the vehicle with the Tach/ Tachless has been programmed. 4 CHIRPS the ignition key.

  • Page 10: System Wiring Details

    1172 SERIES PAGE 11 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 6-PIN CONNECTOR OUTPUT TO ACTIVATE START CIRCUIT YELLOW OUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT GREEN 30A HIGH CURRENT 12VOLT INPUT 30A HIGH CURRENT 12VOLT INPUT SELECTABLE OUTPUT (DEFAULT SECOND IGNITION)
  • Page 11 1172 SERIES PAGE 10 SYSTEM WIRING DETAILS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 STARTER This wire will test 0V with the key off, in the Accessory position and when the YELLOW PIN 1 OUTPUT Ignition is in the on. This wire is 12volts during the start/ crank position only.
  • Page 12 1172 SERIES PAGE 12 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 9 PIN CONNECTOR OUTPUT FOR FACTORY ALARM RE-ARM YELLOW OUTPUT FOR FACTORY ALARM DIS-ARM BROWN AUX OUTPUT 1 - NEG STARTER - PROGRAMMABLE BLACK AUX OUTPUT 2 - NEG TRUNK - PROGRAMMABLE...
  • Page 13 1172 SERIES PAGE 13 SYSTEM WIRING DETAILS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 Supplies one .75 second pulse when locked and one .75 second pulse RE-ARM (-) YELLOW PIN 1 after remote start shutdown. Factory alarm re-arm/ RAP shutdown.
  • Page 14 1172 SERIES PAGE 14 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM WIRING DETAILS 3 PIN BYPASS CONNECTOR GROUND WHEN RUNNING OUTPUT WHITE/VIOLET SYSTEM CHASSIS GROUND INPUT BLACK CONSTANT 12 VOLT INPUT (20AMP) 1- WHITE/VIOLET Wire- Ground When Running (-) Connect this wire to the your bypass modules negative turn on wire.

  • Page 15: Program Menus

    1172 SERIES PAGE 15 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON) 2 - Press and release the Program Switch 1 time. (The Park lights will turn on and the Horn will chip to confirm that program mode was entered) 3 - Select the Program Menu by pressing...
  • Page 16 1172 SERIES PAGE 16 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAMMING ENTERING PROGRAM MODE 1 SYSTEM PROGRAMMING - Menu 1 PROGRAM SWITCH HORN CHIRP PROGRAM SWITCH IGNITION KEY Press and release the 1 CHIRP antenna 1 time or press...
  • Page 17 # Activates Car Finder Mode. SETS OPTION 3 –AUXILIARY CHANNEL OUTPUT- Press and hold the # button to 3 CHIRPS activate auxiliary with unlock and disarm pulse. (DEFAULT) Not Available on 1172 Series SETTING 6- AUX CHANNEL 2 PRESS 6 CHIRPS...

  • Page 18: Program Mode

    1172 SERIES PAGE 18 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE ENTERING PROGRAM MODE 2 IGNITION KEY PROGRAM SWITCH HORN CHIRP REMOTE BUTTON Press UNLOCK 1 CHIRP Button to ON/OFF - ON/OFF - ON Confirming Select Menu 2...
  • Page 19 1172 SERIES PAGE 19 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 3 SYSTEM PROGRAMMING - Menu 1 PROGRAM SWITCH HORN CHIRP REMOTE BUTTON IGNITION KEY Press START 1 CHIRP Button to ON/OFF - ON/OFF - ON...
  • Page 20 1172 SERIES PAGE 20 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE CON'T FROM PREVIOUS PAGE SETTING 3- (+) GLOW PLUG/ INPUT TRIGGER TO START PRESS 3 CHIRP THE HORN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED...
  • Page 21 1172 SERIES PAGE 21 PROGRAM MODE INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 ENTERING PROGRAM MODE 4 PROGRAM SWITCH HORN CHIRP REMOTE BUTTON IGNITION KEY Press # 1 CHIRP Button to ON/OFF - ON/OFF - ON Confirming Select Menu 4...

  • Page 22: Tach Modes

    1172 SERIES PAGE 22 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 PROGRAM MODE TACH / TACHLESS & HYBRID MODES Connect the Tach wire to a Fuel Injector, Coil Pack, Coil or Crank Position Sensor. The system will Tach Learn the first time the car is started.
  • Page 23 1172 SERIES PAGE 23 TRANSMITTER PROGRAMMING INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 SYSTEM PROGRAMMING - Menu 1 The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed together during the same sequence. For security, when a new remote is programmed all previous remote’s are deleted.

  • Page 24: Door Lock Diagrams

    1172 SERIES PAGE 24 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 RELAY DIAGRAMS DOOR LOCK DIAGRAMS Vehicle's Lock/Unlock Switch Door lock Output To Control Relay or Actuators Green Blue Ground Vehicle's Lock/ Unlock Switch Door lock Output 12volts Green Blue...
  • Page 25 1172 SERIES PAGE 25 RELAY DIAGRAMS INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 DOOR LOCK DIAGRAMS Ground Vehicle's Lock/ Unlock Switch Door lock Output 12volts Green Blue Ground Lock Resistor 12volts Unlock Resistor USE SPDT 12v Relay 12volts Lock/ Unlock Switch...

  • Page 26: Diagnostics

    1172 SERIES PAGE 26 INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1 DIAGNOSTICS DIAGNOSTICS CHART If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the start button is pressed the park lights flash 3 times slowly.

  • Page 27: Notes

    1172 SERIES PAGE 27 NOTES INSTALL MANUAL SYSTEM PROGRAMMING - Menu 1...
  • Page 28 1172 SERIES PAGE 28 INSTALL MANUAL **FOR DETAILED VEHICLE WIRING INFORMATION GO TO: http://www.ultrastarters.com/wiring_diagrams.html This site is for registered and authorized dealer only. If you are an authorized dealer but have been registered, please fill out the service request form at http://www.ultrastarters.com/wiring_diagrams.html...

This manual is also suitable for:

1272 series

Table of Contents