Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
ATTENTION
!
-The system must be placed into Service Mode before any service work is started on
the vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done.
The manufacturer accepts no liability or responsibility for accidental starting of the
vehicle.
- CARBON MONOXIDE - Never Start In A Enclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch Must Always Be Installed!
- Never Install Automatic Transmission Remote Starters On Manual Transmission
Vehicles!
Advanced Remote Vehicle
Starting System
AUTOMATIC AND MANUAL
TRANSMISSION MODELS
WWW.ULTRASTARTERS.COM
1350
1350
1350m
1350m
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by
the part responsible for compliance void the user's authority to
operate this devise.
Advertisement
Table of Contents
Related Manuals for Ultra Start 1350
Summary of Contents for Ultra Start 1350
-
Page 1: Installation Guide
(2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate this devise. 1350 1350 1350m 1350m FCC/ID Notice... - Page 2 TABLE OF CONTENTS 1350 Wiring Diagram Pre-Installation Components Pre Installation Check Installation Procedures Wire Connectors 6 Pin Connector 11 Pin Connector 5 Pin Connector 4 Pin Connector Jumper Positions Installation Basic Installation - Quick start Plug-In The Module Auto Tach Learn Programming Program Overview &...
-
Page 3: Wiring Diagram
Installation Guide 30amp Output Starter Heater 30amp Output 30amp Input Power 30amp Input Power Jumper Selectable 30amp Output 30amp Output Ignition 1 (-)500ma Output Factory Re-arm (-)500ma Output Trunk Release (-)500ma Output Factory Disarm (-)500ma Output (-) When Running/Armed (-)500ma Output (-) Horn Honk Park Brake* Negative Input... - Page 4 INSTALLATION TIPS Components - Control module - Remote transmitter(s) - Antenna with built in Program Button and LED’s - 6 pin main harness with dual 30amp power inputs. - 11 pin harness - 5 pin harness - 3 pin keyless entry harness - Hood pin safety switch - Cold Start Temperature Sensor - Installation and Owners Manual...
- Page 5 Installation Guide 6 Pin Power Connector Yellow Starter Green Heater 12 power 12 power Blue Ignition 1 White Select Out 11 Pin Connector Yellow Re-Arm Red/White 3rd CH Brown Disarm Orange (-) Out White/Blue Horn Black/White Park Brake Purple (+) Door White Park Lights Green/White...
- Page 6 QUICK START INSTALL Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow Starter Output Green Heater Output 12 power Input 12 power Input Blue Ignition 1 Output White Selectable Output 11 Pin Power Connector Black System Ground White Park Lights...
- Page 7 Installation Guide Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 4 menus with numerous options and settings that can be easily adjusted for custom installations and applications.
- Page 8 PROGRAMMING PROGRAM MODE 1 - USER SETTINGS Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 2 Ignition Lock Only *3 Ignition Auto Lock Disabled Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Button until you receive the appropriate # of park light flashes and/or horn honks.
- Page 9 Installation Guide PROGRAM MODE 3 - STARTER SETTINGS Setting 1- Special Door Lock/ Unlock 1 Type 1 1 Flash 2 Type 2 2 Flashes Normal Operation 3 Flashes Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
- Page 10 OPERATIONS PROGRAM MODE 4 - TACH SETTINGS Setting 1- Auto Tach Learn. 1) Make all the required wire connections and plug-in the Unit. **The park lights should flash twice upon power up. 2) Turn the Ignition Key ON. (Park Lights will turn on). 3) Start the vehicle, LED’s on antenna will come when proper tach signal is detected**, then after 30-35 seconds the park lights will turn off then flash twice to confirm tach learning.
- Page 11 Installation Guide Transmitter Programming Step 1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if park-lights do not come on at this point, turn key off for 5 seconds, then repeat step 1. Step 3 - Continue to hold the Program Switch, the park lights go out.
-
Page 12: Relay Diagrams
RELAY DIAGRAMS Negative Type Door Locks Vehicle Lock/Unlock Switch Green Positive Type Door Locks Fused +12V Green Blue Note: Always install a in-line fuse when suppling 12volts to relays. Never use the center pin of the keyless entry harness to power relays. 5 Wire / Reverse Polarity Type Door Locks Fused +12V Vehicle...