Page 1
INSTALL GUIDE Covers All 12xx and 13xx Series Advanced Remote Starters www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning!! The system must be placed into Service Mode before any service work is started on the CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH! vehicle.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 4 Recommended Installation Procedures Remote car starters and alarms should be professionally installed. Review the installation and owner manuals and acquire a vehicle wiring diagram for the vehicle to be worked on. Take a few moments to walk around the vehicle looking for any damages and make note if any are found.
Page 5
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 5 Recommended Installation Procedures Mounting The Control Module - Never mount the module in the engine compartment. Select a location under the dash to install the main module. Be certain that the module is securely attached and does not obstruct any serviceable areas.
Page 7
WHITE/VIOLET Ground Output (-)250ma BLACK 12Volt Output (+)250ma NOTE: The 2 pin white and 3 pin white auxiliary connectors are not available on the 12xx series. Jumpers Output on White wire Jumper position 1 2 3 Second Starter Position 1...
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 8 Wiring Descriptions MAIN CONNECTOR (6pin) Function Description 1-YELLOW Starter Output This wire will test 0V in OFF, ACCESSORY and in the ON key positions. 12v during START ONLY. 2-GREEN Heater/Acc Output This wire will test 0V in the OFF and START key positions.
Page 9
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 9 Wiring Descriptions Function Description 9-GREEN/ Hood Pin(-) Input to detect ground when hood is open. WHITE MUST BE CONNECTED. 10-GREEN Door Pin(-) Input to detect (-) when door is open. (“M” series) 11-BLACK Ground(-) System chassis ground input.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 10 Step 1 - Connect All Of the Following Wires Main Connector (6pin) YELLOW Starter Output - 12volts during start position only. GREEN Heater/Acc Output - 12volts in the accessory position off during start and 14volts during run. 12volt 30amp Input - 12volts from ignition harness or battery.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 11 Manual Transmission “M” Models Never install an automatic transmission remote starter into a manual transmission vehicle!!! Doing so may result in serious injury or death. Do not install remote starters in convertible vehicles! The following wires must be connected in addition to the basic remote starter installation.
Page 12
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 12 Auto Tach (Tachless) Learn IMPORTANT! The system must be Tach Learned before remote starting. The Auto Tach Learn is the same for the TL (tachless) series. 1) Turn the ignition key to the “ON” position. The park lights* will turn “ON” 2) Start the vehicle with the key.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 13 Important Tach Notes Tach Learning the remote starter is one of the most important steps in the installation process. Do not tach learn vehicle while the engine is in high idle. To ensure the best possible tach setting, ensure that the vehicle is at low idle/ normal operating RPM.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 14 Entering Program Mode For Menu 1, For Menu 2, Ignition 3x Press and For Menu 3, For Menu 4, press the press the On/Off Release the press the press the On/Off On Program Button button button button...
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 15 Quick View Programming Menu 1 - Press 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Horn Honk Type 1 Type 2 All Honks 3 Lock&Unlock Options Double Unlock 3 second 3/4 second 4 Unlock/Disarm...
Page 16
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 16 Menu 1- User Settings Press and Hold Press and Press and Press and Release Ignition 3x the Program Button Release the Release the the Program Button On/Off to Change Option Program button for # of Times for On/Off On Button...
Page 17
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 17 Menu 2- Additional Settings Press and Press and Release Press and Hold Press and Ignition 3x Release the the Program Button Release the the Program Button On/Off Program # of Times for to Change Option button for On/Off On Button...
Page 18
Press & Hold the Program Button until the appropriate # of park lights/horn (optional) honks, then release. Press & Release the Program Button to proceed to the next step. Setting 2 Gas/Diesel Mode (Auxiliary Connector Pin 12, 12xx series) 1) (+) Input 1 Flash/Honk (+) Glow Plug input.
Page 19
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 19 Menu 3- Starter Settings - continued Setting 4 Run Time 1) 4 Minutes 1 Flash/Honk Runs for approx. 4 minutes when activated. 2) 45 Minutes 2 Flashes/Honks Runs for approx. 45 minutes when activated. *3) 15 Minutes 3 Flashes/Honks Runs for approx.
Page 20
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 20 Menu 4- Tach Settings Press and Press and Press and Release Press and Hold Ignition 3x Release the Release the the Program Button the Program Button On/Off Program # of Times for to Change Option button for On/Off On Button...
“UNLOCK” the remote transmitter the button must be pressed simultaneously with the function chosen. 2nd Car function allows the operation of two Ultra Start systems (in two separate vehicles) with one remote transmitter. Example: Press and release simultaneously to remote start.
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 22 Door Lock Relay Wiring Diagrams Negative Type Door Locks 250ma Vehicle Lock To Control Lock/Unlock Relay or Switch Actuators lock Green Blue Negative Door Locks (More Than 250ma) Fused +12V Vehicle Ground Lock/Unlock Lock lock Switch...
Page 23
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 23 Door Lock Relay Wiring Diagrams 5 Wire / Reverse Polarity Type Door Locks Fused +12V Green Blue Lock Vehicle To Actuator Lock/Unlock Switch lock Aftermarket Doorlock Actuators Ground Vacuum Type Door Locks DIAGNOSTICS Ground Fused +12V Green...
INSTALL MANUAL REMOTE VEHICLE STARTER PAGE 24 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the button is pressed the park lights flash 3 times slowly.