Table of Contents
Advertisement
Maintenance
Turn off the power before performing
0
maintenance.
Wipe using a soft cloth.
0
Wiping with thinner or benzene may melt or
tarnish its surface. For tough stains, wipe using
a cloth that is dipped into a neutral detergent
diluted with water, followed by wiping with a dry
cloth.
When the same position is monitored
0
continuously over a long period, the increased
contact resistance on the horizontal rotation
section may cause noise interferences in the
images and operation from the computer may
become unstable. As such, this product is
equipped with an auto cleaning function that
performs cleaning once a week.
Handling microSD Cards
Do not place any object inside the camera.
0
Inserting an object other than a microSD card
into the microSD card slot may cause fire,
electric shock, or malfunction of the product.
Do not disassemble or modify the microSD card.
0
Before you turn off the power of the camera or
0
remove the microSD card from the card slot,
make sure to press the [Unmount] button on the
[microSD Card Recording] page.
While writing to the microSD card is in progress,
turning off the power or removing the card may
damage the data stored inside it.
(A p.63 [[microSD Card Recording] Page] )
If there is a likelihood that data stored in the
0
microSD card is damaged, remove the microSD
card from the camera, and back up the
necessary data. Next, make use of the SD
Formatter (version 3.1 or later) distributed by the
SD Association to format the microSD card,
followed by inserting the card into the camera.
The SD Formatter is available on the following
website.
https://www.sdcard.org/downloads/
There is a maximum limit to the number of times
0
data on the microSD card can be rewritten.
When approaching to the limit, data recording
and playback may not function properly. In the
event that the recorded data is damaged or
when a playback error occurs, replace the
microSD card with a new one.
Do not use or store the card at a place that is
0
subject to static electricity or electrical noise.
Make sure that the orientation is correct when
0
you insert the microSD card. Inserting the card
forcibly in the wrong orientation may damage the
camera or the microSD card.
(A p.29 [Insert a microSD card. (VN-H657BU)] )
(A p.33 [Insert a microSD card.
(VN-H657WPBU)] )
Our company shall not be liable for any
0
accidental damage caused to the data stored in
the card. Please back up important data on
devices such as a computer.
(A p.104 [[Export(Y/M/D-h:m:s)] Menu] )
To erase data stored in the microSD card
0
completely, it is recommended that you make
use of a commercially-available data erasure
software program, or destroy the microSD card
physically such as by using a hammer.
Use the card within the operational
0
requirements. Do not use it at the following
locations.
Places exposed to direct sunlight
0
Places near thermal equipment
0
In a car under the sun with the windows
0
closed
Places subject to high humidity, corrosion,
0
etc.
Do not bend or drop the card, or subject it to
0
strong impact or vibrations.
Do not wet the card.
0
Do not touch the connection terminals.
0
Prevent dust, dirt, moisture or other foreign
0
substances from being attached to the
connection terminals.
Do not peel off the label attached to the microSD
0
card, or attach another label of sticker over it.
This may cause the equipment to malfunction.
To write characters on a microSD card, do not
0
use a pencil or ballpoint pen. Make sure that a
felt-tip pen is used.
It may be difficult to remove some microSD
0
cards from the slot of the camera.
When removing the microSD card from the card
0
slot, it may sometimes pop out forcefully. Be
careful not to lose it.
Disclaimer
The motion detection, tampering detection, and
0
audio detection features are not intended to
prevent theft or fire. Our company shall not be
liable for any inconveniences or failures that
occur.
We shall not be responsible for any losses
0
incurred in the event of privacy invasion caused
by the videos captured by the camera or audio
of this product.
Saving Energy
If the camera is not to be used for a long time,
0
turn off the power of the system for safety and
energy conservation reasons.
Precautions
11
Advertisement
Table of Contents
