Services Routers SIP and SPA Hardware Installation Guide November 26, 2013 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices. Text Part Number: OL-14126-15...
Page 2
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
Cisco ASR 1013 Router and Slot Numbering for SIP 2-11 Overview: Cisco ASR 1000 Series Aggregation Services Routers SPAs C H A P T E R SPA Summary Checking Hardware and Software Compatibility Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 4
3-25 SFP Module Connections 3-25 SFP Module and Cabling Specifications for Gigabit Ethernet SPAs 3-25 SFP Module Specifications 3-25 SFP Module Cabling and Connection Equipment 3-28 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 5
2-Port, 4-Port, and 8-Port OC-12c/STM-4 Multirate POS SPA Optical Transceiver Modules, Connectors, and Cables 3-50 OC-12 Module Connections 3-51 1-Port OC-192c/STM-64 POS/RPR XFP SPA Overview 3-52 1-Port OC-192c/STM-64 POS/RPR XFP SPA LEDs 3-52 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 7
Verifying the Deactivation and Activation of a SPA Deactivation and Activation Configuration Examples Deactivation of a SIP Configuration Example Activation of a SIP Configuration Example Deactivation of a SPA Configuration Example Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 8
Feature Change to CPU-Usage show Command 7-15 Using debug Commands 7-17 Packing a SPA for Shipment 7-17 Packing a SIP for Shipment 7-20 N D E X Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide viii OL-14126-15...
Document Revision History The Document Revision History records technical changes to this document. The table shows the Cisco IOS XE software release number and document revision number for the change, the date of the change, and a brief summary of the change.
Page 10
Added information about the following Release 3.3.0S SPAs: 1-Port 10-Gigabit Ethernet • LAN/WAN-PHY SPA • 1-Port Channelized OC-3 STM1 ATM Circuit Emulation over Packet (CEoP) SPA (Circuit Emulation Mode only) Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 11
Correction to show support for additional modules for the 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA. Added descriptions for the services • SPAs and double-height SPAs. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 12
Information added for the following Release 2.2 SPAs: 2-Port and 4-Port OC-48c/STM-16 • POS SPA 1-Port Channelized STM-1/OC-3 • Cisco IOS XE OL-14126-01 April 25, 2008 First release. Release 2.1 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
You can also refer to the specific Cisco IOS XE software document for a particular feature. To see if a feature is supported by a Cisco IOS XE release, to locate the software document for –...
Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
SIP and SPA Compatibility, page 1-3 Modular Optics Compatibility, page 1-5 • For software details for the specific SIPs and SPAs that are supported on the Cisco ASR 1000 Series Aggregation Services Routers, refer to the companion publication, Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide.
Double-height SPA Caution SIP subslot 0 is not available on the Cisco ASR 1002 Router as that is the slot occupied by the integrated Route Processor with native Gigabit Ethernet ports. Each SPA provides a certain number of connectors, or ports, that are the interfaces to one or more •...
For more information about the support for different SIPs and SPAs, refer to the “Release History” Note section in the “Overview of the SIP” chapter of the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide.
Chapter 1 SIP and SPA Product Overview SIP and SPA Compatibility 1. The 10-Port Gigabit Ethernet SPA is a double-height SPA. The 10-Port Gigabit Ethernet SPA is not supported on Cisco ASR 1001 or Cisco ASR 1002-F Routers. Table 1-3...
(PPP) over ATM is not supported. IETF RFC 1577 support for classical IP and Address Resolution Protocol (ARP) over ATM is not supported. ATM Forum UNI 3.0, 3.1, and 4.0 is not supported. Effective from Cisco IOS XE Release 3.5.0S, the SPA-2CHT3-CE-ATM supports ATM on clear-channel E3 SPA.
SPA. For more information about any of the supported transceivers for SPAs in these tables, refer to the Cisco Transceiver Modules site for that module on Cisco.com at: http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_installation_guides_list.html...
Page 23
CWDM Optics Compatibility for Built-in Gigabit Ethernet Ports (4x1GE) and All Gigabit Ethernet SPAs Supported on the Cisco ASR 1000 Series Routers Qualified Optics Modules (Cisco Part Numbers) CWDM-SFP-1470= CWDM-SFP-1490= CWDM-SFP-1510= CWDM-SFP-1530= CWDM-SFP-1550= CWDM-SFP-1570= CWDM-SFP-1590= CWDM-SFP-1610= Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
SIP40G Release 3.1S 1. The Cisco ASR1000-SIP40 carrier card supports four half-height SPAs, two full-height SPAs, or a combination of two half-height and one full-height SPAs. Double-wide SPAs are not supported. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide...
ASR1000-ESP40 3.2S 1. The Cisco ASR 1013 Router has limitation to support ASR1000-SIP40 at slots 4 and 5 at 40G mode. If a ASR1000-SIP40 is installed at slots 4 or 5, it will work as a SIP10 at 10G mode.
Identifying Slots and Subslots for SIPs and SPAs This section describes how to specify the physical locations of a SIP and SPA on the Cisco ASR 1000 Series Routers within the command-line interface (CLI) to configure or monitor the devices.
Page 30
Identifying Slots and Subslots for SIPs and SPAs Figure 2-1 shows an example of a SIP installed on a Cisco ASR 1006 Router. The router has three chassis slots for SIPs, and can accommodate a total of twelve SPAs. Figure 2-1...
SPA Product Overview” chapter of the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide. The Cisco ASR 1000 series SIP supports four subslots for the installation of SPAs. As shown in Figure 2-2, the subslot locations are oriented as follows: SIP subslot 0—Top-left subslot...
Page 32
SIP subslot 3—Bottom-right subslot • On the Cisco ASR 1002 Router and Cisco ASR 1002-X Router, SIP subslot 0 is not available for SPA Note insertion. It is the slot that is used for the integrated Route Processor and Gigabit Ethernet ports.
07051650 12.2(33r)XN2 Cisco ASR 1000 Series SPA Interface Processor Overview This section provides an overview of the SPA Interface Processor (SIP) supported on the Cisco ASR 1000 Series Routers. This section contains the following topics: • Cisco ASR1000-SIP10 Overview, page 2-7 •...
Physical dimension (HxWxD) 1.630 inches (41.4 mm) x 16.725 inches (424.8 mm) x 14.187 inches (360.3 mm) Shipping weight 8.5 lb (3.9 kg) Operating temperature Nominal—40.9°F to 104°F (5 to 40°C) Short Term—40.9°F to 131°F (5 to 55°C) Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
–40°F to 158°F (–40°C to 70°C) Cisco ASR1000-SIP40 Overview The Cisco ASR1000-SIP40 supports up to 40 Gbps total bandwidth for the four SPA bays and 46 Gbps sustained through carrier card when utilizing two four-link 6.25GHz ESIs. Following are the features of the Cisco ASR1000-SIP40: Supports 40 Gbps of non oversubscribed throughput.
Green The Cisco ASR1000-SIP40 is online. The Cisco ASR1000-SIP40 is powered off. Green The Cisco ASR1000-SIP40 is powered on. The Cisco ASR1000-SIP40 is powered off. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 2-10 OL-14126-15...
• Two half-height and one full-height SPA combination that does not exceed 96 ports • The Cisco ASR 1013 Router uses the same SPA subslot numbering as the Cisco ASR 1006 Router and Cisco ASR 1004 Router. Figure 2-5 Cisco ASR 1013 Router SPA Interface Slot Numbering...
Cisco ASR 1013 Routers. The Cisco ASR1000-ESP10 and Cisco ASR1000-ESP20 will not plug into the Cisco ASR 1013 Router Note ESP slots. The Cisco ASR 1013 Router supports six SIP slots only with the combination of Cisco ASR1000-ESP40 and RP2. Figure 2-6...
Page 39
Cisco ASR 1000 Series SPA Interface Processor Overview SPA—Slot 0 SPA—Slot 5 SPA—Slot 1 RP-2—R1 SPA—Slot 2 ESP-40/ESP-100—F1 SPA—Slot 3 RP-Filler—F0 SPA—Slot 4 10 RP-2—R0 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 2-13 OL-14126-15...
Page 40
Chapter 2 Overview: Cisco ASR 1000 Series Aggregation Services Routers SIPs Cisco ASR 1000 Series SPA Interface Processor Overview Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 2-14 OL-14126-15...
Page 41
C H A P T E R Overview: Cisco ASR 1000 Series Aggregation Services Routers SPAs This chapter describes the shared port adapters (SPAs) that are supported on the Cisco ASR 1000 Series Aggregation Services Routers and contains the following sections: •...
2-Port Channelized T3/E3 ATM CEoP SPA Overview, page 3-78 • 24-Port Channelized T1/E1/J1 ATM CEoP SPA Overview, page 3-80 • SPA Summary Summary descriptions of the SPAs that are supported on the Cisco ASR 1000 Series Routers are provided in Table 3-1. Table 3-1...
To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SIPs or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for individual hardware modules or components.
Cisco ASR1000-SIP10. Each Cisco ASR1000-SIP10 supports 4 single-height SPAs. The chassis models of the Cisco ASR 1000 Series Aggregation Services Routers support a different maximum number of SIPs as follows: Cisco ASR 1002 Router, Cisco ASR1002-Fixed Router, and Cisco ASR1002-X Router—1...
• Double-wide SPAs are not supported on Cisco ASR1000-SIP40. Warning The chassis models of the Cisco ASR 1000 Series Aggregation Services routers support a different maximum number of Cisco ASR1000-SIP40 as follows: Cisco ASR 1006 Router — three SIPs •...
SONET and SDH single-mode and multimode optical fiber connection (see Figure 3-2). Each SPA port accepts an SFP module with a duplex LC-type receptacle that allows connection to single-mode or multimode optical fiber. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
SONET and SDH network connectivity with a per-port bandwidth of 622.08 Mbps. For more information about SPA bandwidth, see the “Bandwidth Oversubscription” section in this chapter. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Port is enabled by software, and loopback is on. Amber STATUS SPA power is off. Amber SPA power is on and good, and SPA is being configured. Green SPA is ready and operational. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-10 OL-14126-15...
Multimode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4) • Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns. Single-mode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4) • Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-11 OL-14126-15...
The 4-Port and 8-Port Fast Ethernet SPA has two types of LEDs: an A/L LED for each port on the SPA, and one STATUS LED, as shown in Figure 3-7. Figure 3-7 8-Port Fast Ethernet SPA Faceplate A/L (Active/Link) LED STATUS LED Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-12 OL-14126-15...
(EMI) and susceptibility to common-mode sources. Wire pairs 4/5 and 7/8 are actively terminated in the RJ-45 port circuitry in the 4-Port and 8-Port Fast Ethernet SPA. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-13 OL-14126-15...
Port is enabled by software and the link is down. STATUS SPA power is off. Green SPA is ready and operational. Amber SPA power is on and good, and the SPA is being configured. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-15 OL-14126-15...
• Single-mode very-long-reach (ZR) XFP module—XFP-10GZR-OC192LR Cisco qualifies the optics that are approved for use with its SPAs. The above-listed small form-factor pluggable modules (XFPs) are the only optical transceiver modules qualified for use. Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network.
Page 57
10GLR SR-1: 0.5 dBm 10GER IR-2: –1.0 dBm 10GZR LR-2: –7.0 dBm Maximum receiver power damage 10GLR SR-1: 5 dBm 10GER IR-2: 5 dBm 10GZR LR-2: 5 dBm Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-17 OL-14126-15...
Port is not enabled. Green Port is enabled and the link is up. Amber Port is enabled and the link is down. STATUS SPA power is off. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-18 OL-14126-15...
RJ-45 receptacles. You can use both interface connectors simultaneously. Each connection supports IEEE 802.3 and Ethernet 10/100BASE-T interfaces compliant with appropriate standards. Cisco does not supply Category 5 unshielded twisted pair (UTP) RJ-45 cables; these cables are available commercially.
The 5-Port Gigabit Ethernet SPA has two types of LEDs: an A/L LED for each port on the SPA, and one STATUS LED, as shown in Figure 3-17. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-20 OL-14126-15...
Page 61
Overview: Cisco ASR 1000 Series Aggregation Services Routers SPAs 5-Port Gigabit Ethernet SPA Overview Figure 3-17 5-Port Gigabit Ethernet SPA Faceplate A/L (Active/Link) LED STATUS LED Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-21 OL-14126-15...
SFP modules exist for technologies other than Gigabit Ethernet and for products other than the 8-Port Gigabit Ethernet SPA. However, the information in this document pertains only to SFP modules that plug into the 8-Port Gigabit Ethernet SPA ports. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-23 OL-14126-15...
Port is not enabled. Green Port is enabled and the link is up. Amber Port is enabled and the link is down. STATUS SPA power is off. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-24 OL-14126-15...
The SFP module has a receiver port (RX) and a transmitter port (TX) that compose one optical interface. Table 3-15, Table 3-16, Table 3-17, Table 3-18, and Table 3-19 provide SFP module information and specifications. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-25 OL-14126-15...
Page 66
(SMF) of up to 10-Km link length with 1310 nm wavelength. GLC-ZX-SMD 1000BASE-ZX SFP Contains a Class 1 laser of 1550 nm for transceiver module 1000BASE-ZX (extended-wavelength) applications. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-26 OL-14126-15...
Page 67
802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach 6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-27...
SFP-GE-Z is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the SFP-GE-Z is 24.9 miles (40 km). Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-28...
(DWDM) SFP modules are given in the following sections: CWDM SFP Module Specifications for All Gigabit Ethernet SPAs Using SFP Modules, page 3-30 • DWDM SFP Module Specifications, page 3-31 • Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-29 OL-14126-15...
Port is enabled by the software, and the link is valid. Amber and This state is unused and its meaning is undefined. green Debug LED Green Indicates a SPA OK status to the host. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-32 OL-14126-15...
Interface Type and Density 2x1 GE Local Timing Interfaces Input; Output Local Timing Frequency 1.544 MHz / 2.048 MHz BITS Interface Support In; Out SSM Support Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-33 OL-14126-15...
Figure 3-21 SFP Optics Module Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-34 OL-14126-15...
SPA, and one STATUS LED, as shown in Figure 3-22. Figure 3-22 4-Port OC-3c/STM-1 POS SPA Faceplate C/A (Carrier/Alarm) LED STATUS LED A/L (Active/Loopback) LED Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-35 OL-14126-15...
SONET and SDH single-mode and multimode optical fiber connection (see Figure 3-23). Cisco qualifies the optics that are approved for use with its SPAs. The 2-Port and 4-Port OC-3c/STM-1 POS SPA supports the following types of optical transceiver modules: Multimode (MM) SFP module—SFP-OC3-MM •...
Page 77
2-Port and 4-Port OC-3c/STM-1 POS SPA-equipped routers back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between them. Figure 3-24 LC-Type Cables Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-37 OL-14126-15...
The 1-Port OC-48c/STM-16 POS SPA provides Packet over SONET (POS) network connectivity with a bandwidth of 9.95 Gbps. The following sections describe the 1-Port OC-48c/STM-16 POS SPA: Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-38 OL-14126-15...
Green Port is enabled by software. Amber Port is enabled by software, and there is at least one alarm. Port is not enabled by software. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-39 OL-14126-15...
OC-48c/STM-64 line rates (9.95 Gbps). Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]), and is mapped into the STS-48/STM-64 frame. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-40 OL-14126-15...
Port is not enabled by software. Green Port is enabled by software, and loopback is off. Amber Port is enabled by software, and loopback is on. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-42 OL-14126-15...
LC-type cable (see Figure 3-28) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX). Figure 3-28 LC-Type Cables Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-43 OL-14126-15...
The 1-Port OC-12c/STM-4 POS SPA has three types of LEDs: two LEDs for each port on the SPA, and one STATUS LED, as shown in Figure 3-29. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-44 OL-14126-15...
RFC 1155, Structure and Identification of Management Information for TCP/IP-based Internets • RFC 1156, Management Information Base for Network Management of TCP/IP-Based Internets • RFC 1157, Simple Network Management Protocol (SNMP) • Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-45 OL-14126-15...
SONET and SDH single-mode and multimode optical fiber connection (see Figure 3-30). Cisco qualifies the optics that are approved for use with its SPAs. The 1-Port OC-12c/STM-4 POS SPA supports the following types of optical transceiver modules: • Multimode (MM) SFP module—SFP-OC12-MM •...
Three different faceplates exist for the 2-Port, 4-Port, and 8-Port OC-12c/STM-4 Multirate POS SPAs. Note They each contain the same LEDs and the number of ports are 2, 4, and 8 respectively. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-48 OL-14126-15...
The 2-Port, 4-Port, and 8-Port OC-12c/STM-4 Multirate POS SPA interface complies with the following IETF RFCs: RFC 1662, PPP in HDLC-like Framing • RFC 2427, Multiprotocol Interconnect over Frame Relay Encapsulation • RFC 2615, PPP over SONET/SDH • Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-49 OL-14126-15...
OC-3-equipped or OC-12-equipped routers back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-50 OL-14126-15...
The 1-Port OC-192c/STM-64 POS/RPR XFP SPA has six LEDs, as shown in Figure 3-35. Figure 3-35 1-Port OC-192c/STM-64 POS/RPR XFP SPA Faceplate SPA-0C192POS-XFP WRAP LED CARRIER LED PASSTHRU LED ACTIVE LED MATESYNC LED STATUS LED Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-52 OL-14126-15...
Page 93
The 1-Port OC-192c/STM-64 POS/RPR XFP SPA uses a single-mode, 9.95 Gbps, OC-192c optical fiber (SONET STS-192c or SDH STM-64) optical transceiver module for SONET and SDH connection to the network. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-53 OL-14126-15...
Figure 3-37. Figure 3-37 4-Port Clear-Channel T3/E3 Serial SPA Faceplate SPA-4XT3/E3 C/A (Carrier/Alarm) LED RX (Receive) connector A/L (Active/Loopback) LED STATUS LED TX (Transmit) connector Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-55 OL-14126-15...
The interface connectors on the 2-Port, 4-Port, and 8-Port Clear-Channel T3/E3 SPA are 75-ohm coaxial 1.0/2.3 cables that are specific to the T3/E3 SPA, with one connector and cable for transmit (TX) and one for receive (RX). Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-56 OL-14126-15...
CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to mini BNC-Female, 10 feet) • • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) The Cisco cable part numbers are 72-4124-01 (with male BNC end) and 72-4131-01 (with female BNC Note end). Figure 3-37...
STATUS LED, as shown in Figure 3-38. Figure 3-38 4-Port Channelized T3 SPA Faceplate SPA-4XCT3/DS0 C/A (Carrier/Alarm) LED RX (Receive) connector A/L (Active/Loopback) LED STATUS LED TX (Transmit) connector Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-58 OL-14126-15...
CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to mini BNC-Female, 10 feet) CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • The Cisco cable part numbers are 72-4124-01 (with Male BNC end) and 72-4131-01 (with Female BNC Note end).
The 4-Port Serial Interface SPA has three types of LEDs: two LEDs for each port on the SPA, and one STATUS LED, as shown in Figure 3-39. Figure 3-39 4-Port Serial Interface SPA Faceplate SPA-4XT-SERIAL ACTIVE LED STATUS LED CD/LB (Carrier Detect/Loopback) LED Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-60 OL-14126-15...
4-Port Serial Interface SPA Interface Specifications The 4-Port Serial Interface SPA supports six interfaces in DCE and DTE mode: V.35 • • EIA/TIA-232 EIA/TIA-449 • Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-61 OL-14126-15...
Port is enabled by software, and there is a valid T1 or E1 signal without any alarms. Amber Port is enabled by software, and there is at least one alarm. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-64 OL-14126-15...
Table 3-41 RJ-45 Connector Pinouts Signal Description RX– Receive ring – Receive tip + No connection TX– Transmit ring – Transmit tip + No connection Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-65 OL-14126-15...
OC-3c/STM-1 line rates (155.52 Mbps). Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]), and is mapped into the STS-3c/STM-1 frame. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-67 OL-14126-15...
1-Port Channelized STM-1/OC-3 SPA-equipped routers back-to-back. Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-68 OL-14126-15...
1-Port Channelized OC-12/STM-4 SPA Faceplate SPA-1XCHOC12/DS0 C/A (Carrier/Alarm) LED STATUS LED A/L (Active/Loopback) LED The 1-Port Channelized OC-12/STM-4 SPA LEDs are described in Table 3-43. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-69 OL-14126-15...
The 1-Port Channelized OC-12/STM-4 SPA uses a small form-factor pluggable (SFP) optical transceiver module installed in each port for SONET and SDH single-mode and multimode optical fiber connection (see Figure 3-47). Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-70 OL-14126-15...
Page 111
Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Figure 3-48 LC Type Cables Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-71 OL-14126-15...
Cisco WebEx Node for ASR 1000 Series Overview The Cisco WebEx Node for Cisco ASR 1000 Series SPA (also referred to as the Cisco WebEx Node SPA) is a double-height SPA that improves the functionality of WebEx meeting services. The traffic between the enterprise network and the WebEx Data Center is decreased, greatly reducing Internet bandwidth requirements.
SPA power is on and good, and SPA is being configured. Blinking SPA is undergoing FPD upgrade operation. Because the Cisco WebEx Node SPA is a services type of SPA, it does not support routable interfaces. Note Cisco DSP SPA for ASR 1000 Series Overview To provide voice transcoding and transrating functionalities on Cisco ASR 1000 Series Routers, Cisco SPA-DSP (also referred to as SPA-DSP) has been introduced from Cisco IOS XE Release 3.2S.
SPA-DSPs have only one type of LED, which is the STATUS LED type, as shown in Figure 3-50. Figure 3-50 SPA-DSP Faceplate STATUS LED Table 3-48 describes the SPA-DSP LED. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-75 OL-14126-15...
1-Port Channelized OC-3 ATM CEoP SPA Optical Transceiver Modules and Cables Cisco Systems, Inc. qualifies the optics that are approved for use with its SPAs. The 1-Port Channelized OC-3 ATM CEoP SPA supports the following types of optical transceiver modules: Multimode (MM) SFP module (500m)—SFP-OC3-MM...
Port is enabled by software, loopback is on. STATUS SPA power is off. Amber SPA power is on and the SPA is being configured. Green SPA is ready and operational. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-78 OL-14126-15...
CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • The Cisco cable part numbers are 72-4124-01 (for the male BNC end) and 72-4131-01 (for the female Note BNC end). A SPA can receive data over the cable up to a maximum distance of 1350 ft (411.5 meters).
The 24-Port Channelized T1/E1/J1 CEoP SPA has two types of LEDs, as shown in the following figure: Figure 3-53 24-Port Channelized T1/E1/J1 CEoP SPA Faceplate TX / RX A/C (Alarm/Carrier) LEDs STATUS LED Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-80 OL-14126-15...
The 24-Port Channelized T1/E1/J1 CEoP SPA requires a Cisco cable (part number CABLE-24T1E1J1), which is shown in Figure 3-54. Figure 3-54 24-Port Channelized T1/E1/J1 CEoP SPA High-Density Cable Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-81 OL-14126-15...
TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 3 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-82 OL-14126-15...
Page 123
TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 13 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-83 OL-14126-15...
Page 124
TX Tip Not connected TX Ring RX Tip Not connected RX Ring Line 23 TX Tip Not connected TX Ring RX Tip Not connected RX Ring Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-84 OL-14126-15...
A 24-port channelized T1/E1/J1 CEoP SPA patch panel with the DCC2484/25T1-S part number is available from Optical Cable Corporation (OCC) at: http://www.occfiber.com/main/index.php This is a shielded rack mount 24-port patch panel, 2RU, accessory component for the Cisco PID SPA-24CHT1-CE-ATM. You can view the image of patch panel with the DCC2484/25T1-S part number http://www.occfiber.com/main/index.php?m=1&p=2&s=Y&l=en&it=54&i=193...
Page 126
Chapter 3 Overview: Cisco ASR 1000 Series Aggregation Services Routers SPAs 24-Port Channelized T1/E1/J1 ATM CEoP SPA Overview Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 3-86 OL-14126-15...
Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might harm you. A warning symbol precedes each warning statement. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 129
Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 130
Chapter 4 Preparing to Install a SIP or a SPA Safety Guidelines Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 131
Chapter 4 Preparing to Install a SIP or a SPA Safety Guidelines Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 132
Statement 1029 Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 133
Statement 1043 The covers are an integral part of the safety design of the product. Do not operate the unit without the Warning covers installed. Statement 1077 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Handle carriers by available handles or edges only; avoid touching the printed circuit boards or • connectors. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Warning Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 136
Chapter 4 Preparing to Install a SIP or a SPA Laser/LED Safety Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 4-10 OL-14126-15...
C H A P T E R Installing and Removing a SIP This chapter describes how to install or remove SIPs on the Cisco ASR 1000 Series Aggregation Services Routers. This chapter contains the following sections: Handling SIPs, page 5-1 •...
Preparing for Online Removal of a SIP The Cisco 7600 series router support OIR of the SIP. To perform an OIR, power down a SIP which automatically deactivates any installed SPAs and remove the SIP with the SPAs still intact.
SIP in the Cisco ASR 1000 Series Router. For example, consider the case where you remove a SIP from the Cisco ASR 1000 Series Router to replace it with another SIP. You reinstall the same SPAs into the new SIP. When you enter the hw-module slot start command on the Cisco ASR 1000 Series Router, the SPAs automatically reactivate with the new SIP.
03:19:46 ASR1006-PWR-AC 03:19:14 ASR1006-FAN 03:19:14 The following example shows the Cisco ASR 1000-SIP10 installed in slot 0 and Cisco ASR1000-SIP40 installed in slots 1,2,3, and 4 of the Cisco ASR 1013 Router: Router# show platform Chassis type: ASR1013 Slot Type...
The Cisco 7600 series router support the OIR of a SPA independent of removing the SIP. This means that a SIP can remain installed in the Cisco ASR 1000 Series Router with one SPA remaining active, while you remove another SPA from one of the SIP subslots. If you are not planning to immediately replace a SPA into the SIP, ensure that you install a blank filler plate in the subslot.
Page 142
If you choose to use the hw-module subslot stop command in EXEC mode, you cause the SPA to gracefully shut down. However, the SPA will come up again when executing the hw-module subslot start command. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
SPA prior to removal when using the hw-module subslot command in global configuration mode. If the Cisco ASR 1000 Series Router is running, then the SPAs automatically start upon insertion into the SIP or with insertion of a SIP into the Cisco ASR 1000 Series Router.
EXEC configuration mode. Observe the Operational Status field associated with the SPA that you want to verify. In the following example, the SPA located in subslot 1 of the SIP in slot 2 of the Cisco ASR 1000 Series Router is administratively down from the hw-module subslot shutdown command:...
Deactivate a SPA when you want to perform OIR of that SPA. The following example deactivates the SPA (and its interfaces) that is installed in subslot 0 of the SIP located in slot 1 of the Cisco ASR 1000 Series Router and removes power to the SPA.
Page 146
Slide the SIP out of the router slot. If you are removing a blank filler plate, pull the blank filler plate Step 3 completely out of the router slot. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 5-10 OL-14126-15...
Page 147
Chapter 5 Installing and Removing a SIP SIP Installation and Removal Figure 5-2 illustrates how to install and remove a SIP in Cisco ASR 1000 Series Routers. Figure 5-2 SIP Installation and Removal -SI P1 0 AS R1 000 PW R STA...
Page 148
Chapter 5 Installing and Removing a SIP SIP Installation and Removal Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 5-12 OL-14126-15...
C H A P T E R Installing and Removing a SPA This chapter describes how to install or remove SPAs on the Cisco 7600 series router. This chapter contains the following sections: Handling SPAs, page 6-1 • • SPA Installation and Removal, page 6-2 Online Insertion and Removal, page 6-6 •...
Before you remove a SPA from the SIP, read this important information about SPA cable clips that will help to make removing the SPA easier. The SPA accessory kit is shipped with three different versions of cable clips, as shown in Figure 6-3. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 151
To install a cable clip to each side of the SPA, follow these steps: Step 1 Select one set of cable clips from the SPA accessory kit. Figure 6-3 shows the cable clip options. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Page 152
SPA, as shown in Figure 6-4. Figure 6-4 Installing a Cisco ASR 1000 Series Cable Clip into the SPA Plastic Pull Tab Portion of the cable clip that locks into position SPA plastic pull tab...
Page 153
To remove the SPA from the SIP, unfasten the captive installation screws on either side of the SPA. Step 6 Figure 6-6 illustrates how to remove a SPA in a SIP. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
This completes the procedure for removing a SPA from the SIP. Online Insertion and Removal Cisco 7600 series router SIPs and SPAs support online insertion and removal (OIR). SPAs can be inserted or removed independently from the SIP. OIR of a SIP with installed SPAs is also supported.
When the SIP and SPA STATUS LEDs are green, all associated interfaces are configurable. Note Refer to the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide for configuration instructions. If a SIP or SPA is replaced with a module of the same type (as in an OIR or hardware swap), the •...
For more information about FPD upgrades, refer to the “Upgrading Field-Programmable Devices” chapter of the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide. Use the show version command to obtain a few details on the installed SIPs and interfaces.
SPAs. If you plan to install a new SPA in a subslot that is not in use, you must first remove the SPA blank filler plate. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
To remove the cable management bracket, depress the button on the bracket and pull it out. Step 3 Blank filler plugs are provided if no cable management brackets are installed. Note Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 6-10 OL-14126-15...
C H A P T E R Troubleshooting the Installation This chapter describes how to troubleshoot the installation of SIPs and SPAs on the Cisco ASR 1000 Series Aggregation Services Routers. This chapter contains the following sections: Troubleshooting the Hardware, page 7-1 •...
Refer to the configuration section of the SPA installation and configuration guide. Also, refer to the Cisco IOS software configuration documentation listed in the “Related Documentation” section on page xiii. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
This section describes some of the possible hardware problems that can occur with the Cisco WebEx Node for ASR 1000 Series (also called the Cisco WebEx Node SPA) hardware and DSP SPA for Cisco ASR 1000 Series. It includes the following problems: Cisco WebEx Node SPA and SPA-DSP is in Out-of-Service State, page 7-3 •...
Page 162
Cisco WebEx Node SPA or SPA-DSP in the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide. Table 7-3 Possible Problems and Solutions for Hardware-Based Out-of-Service States on the Cisco WebEx Node SPA and SPA-DSP Possible Problem Observations and Comments...
Page 163
Chapter 7 Troubleshooting the Installation Troubleshooting the Hardware Table 7-3 Possible Problems and Solutions for Hardware-Based Out-of-Service States on the Cisco WebEx Node SPA and SPA-DSP (continued) Possible Problem Observations and Comments Solutions Temperature or • The show hw-module subslot all oir command...
Page 164
Chapter 7 Troubleshooting the Installation Troubleshooting the Hardware Table 7-3 Possible Problems and Solutions for Hardware-Based Out-of-Service States on the Cisco WebEx Node SPA and SPA-DSP (continued) Possible Problem Observations and Comments Solutions Temperature or Execute the show hw-module subslot sensors command...
Troubleshooting the Installation Troubleshooting the Hardware Cisco WebEx Node SPA Has Issued Hardware Error Messages There are several different error messages for the Cisco WebEx Node SPA that might appear in the output of the show logging command. Table 7-4 provides an example of error messages of the SPA_CPU_ERR type.
Troubleshooting the Hardware Hard Disk Drive Errors on the Cisco WebEx Node SPA The Cisco WebEx Node SPA has a hard disk drive (HDD) used by the Cisco WebEx Node application. It stores logs and provides a cache for meeting data.
Page 167
Exit the SPA console using the exit command, as shown in the following example: service-spa# exit Router# Reload the Cisco WebEx Node SPA using the hw-module subslot reload command. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide OL-14126-15...
Collecting the show tech-support Output from the Cisco WebEx Node SPA Console When reporting a problem to Cisco technical support, you should first obtain the output of the show tech-support command from the WebEx Node SPA console. The following example show how to run the command and redirect the output to a file on a TFTP server: service-spa# show tech-support >...
Prerequisites Before you can format the hard disk on a Cisco WebEx Node SPA, the disk must be unmounted not in use. If you attempt to format the disk while the disk is mounted, you will receive a warning as shown in...
Page 170
180 days, whichever comes first. Use tune2fs -c or -i to override. Creating CONFIG partition on /dev/sda2 ... mke2fs 1.40 (29-Jun-2007) Filesystem label=CONFIG OS type: Linux Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 7-12 OL-14126-15...
Page 171
The SPA-DSP has neither a CPU nor a hard disk as compared to the WebEx Node SPA. Hence, there are no CPU error messages or hard disk error messages for a SPA-DSP. Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 7-13...
6-2. Note Caution The Cisco original packaging is to be used for the shipment of all SPAs and cable management brackets. Failure to properly use Cisco packaging can result in damage or loss of a product. Caution During this procedure, wear grounding wrist straps to avoid ESD damage to the card.
Page 176
Step 6 Close the exterior carton. Step 7 Apply tape over the exterior carton flap to ensure that the carton stays closed during shipping. Step 8 Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 7-18 OL-14126-15...
Page 177
Chapter 7 Troubleshooting the Installation Packing a SPA for Shipment Figure 7-1 Packing a SPA for Shipment Clamshell Cushion foam Exterior carton Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 7-19 OL-14126-15...
“SIP Installation and Removal” section on page 5-9. Note The Cisco original packaging is to be used for the shipment of all SIPs. Failure to properly use Cisco Caution packaging can result in damage or loss of a product. During this procedure, wear grounding wrist straps to avoid ESD damage to the card.
Page 179
Packing a SIP for Shipment Figure 7-2 Packing a SIP for Shipment Corrugated spacer Bottom support for inner carton Inner carton Foam packing cushions Exterior carton Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 7-21 OL-14126-15...
Page 180
Chapter 7 Troubleshooting the Installation Packing a SIP for Shipment Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware Installation Guide 7-22 OL-14126-15...