Denon Link Setup; Pure Direct Setup - Denon DVD-A1UD Owner's Manual

ENGLISH
Setting items
XLR GTerminal PolarityH : Set the polarity of the XLR terminal.
Set the signal to be output
• Normal : Normal polarity.
from the XLR terminal. • Inversion : Reverse the polarity.
GGain UpH : Can increase output gain when the input sensitivity of a
device connected via XLR is low.
• Off : Outputs at standard gain from the XLR terminal.
• On : Increase the output gain of the XLR terminal. Set when the input
sensitity of the connected device is low.
The default DVD-A1UD balance model XLR audio connectors pin
alignment is as shown.

DENON LINK Setup

Set the audio signal to be output from the DENON LINK terminal.
Setting items
DENON LINK Mode
GOffH : Do not use DENON LINK.
Set the audio output of
G2ndH : Output digital audio using DENON LINK 2nd Edition.
DENON LINK. G3rdH : Output digital audio using DENON LINK 3rd Edition.
G4thH : Output digital audio using DENON LINK 4th Edition.
Compatible with jitter-free connection. For more information, refer to
"DENON LINK Connection q Making a Jitter-free Connection" (vpage
18).
• HDMI 1 : Improve HDMI1 digital signal jitter.
• HDMI 2 : Improve HDMI2 digital signal jitter.
• When set to "4th", the HDMI control function becomes available from
the connected device.
• When "4th" is set and jitter-free connection is set up, audio affected
by the jitter-free function is output from the HDMI terminal during
BD playback. When playing back media other than that, video signal
is output from the HDMI terminal and audio signal is output from the
DENON LINK terminal, respectively.
• To play DENON LINK 4th signals, connect to a DENON LINK 4th-
compatible AV Amp using an HDMI and a DENON LINK cable.
• About the 4th setting of the AV Amp, see the owner's manual of the
AV Amp.
Remote control operation
0 buttons
Setting contents
q GROUND w HOT e COLD
Default settings are underlined.
Setting contents
Displaying the menu
:
Cancel the menu
Signals Compatible with DENON LINK Setting and Transmission
n
Audio Setup
The DENON LINK setting for the DENON LINK version of the connected AV Amp is as follows:
DENON LINK version of
AV Amp
2nd Edition
("S.E." displayed near
terminal)
3rd Edition
("3rd" displayed near
terminal)
4th Edition
("4th" displayed near
terminal)
NOTE
With DENON LINK connections, no audio signals other than those of BD are output from the HDMI
terminal.
(When "DENON LINK Mode" is set to "2nd" and "HDMI Setup" – "SA-CD Audio Out" (vpage 26) is set
to "On", the audio signals of Super Audio CD are output from the HDMI terminal.)

Pure Direct Setup

Makes settings regarding digital audio and video output modes during Pure Direct mode,
as well as display messages. Two types of setting can be registered.
Setting items
User Preset 1/
User Preset 2
This sets the operating mode
for "User Preset 1" or "User
Preset 2" selected by
Setting each of these items
to "Off" enables output of
high quality analog signals
free of interference from the
associated circuits.
Moves the cursor
:
(Up/Down/Left/Right)
Media
The DENON
BD
LINK setting
(During DVD- DVD-
of the DVD-
jitter-free Video Audio
A1UD
connection)
"2nd"
A S S
"3rd"
A S S
"4th"
S S S
Default settings are underlined.
Setting contents
GDigital OutH : Set whether to output signals to the digital audio output
terminal.
• On : Enable digital audio output.
Off : Disable digital audio output.
•
.
GVideo OutH : Set option of video output.
• On : Enable video output.
Off : Disable video output. This setting also disables audio output from
•
the HDMI terminal.
GDisplayH : Set option for front panel display.
• On : Turn on display.
Off : Turn off display.
•
For more information, see "Playing Back High-quality Audio (Pure Direct
Function)" (vpage 40).
:Decision the setting :Return to previous menu
Super
audio CD SD
CD
A S S
S S S
S S S