7 • Completing Your Installation With or Without a Light Fixture....... 11 • To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state speed control with this fan. Use only Hunter speed 8 • Operating and Cleaning controls.
Page 3
Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation fl exibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profi le, Standard, or Angle mounting. e steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Do not over tighten. Steps 2-2 – 2-4 Step 2-3 (Angled Ceiling Only) Flat Washer 3” Screw For Angled Ceilings: Be sure to orient the hanger bracket with the large opening towards the ceiling peak. 42027-01 • 12/09/05 Hunter Fan Company...
Go to 4 • Wiring the Fan. WARNING: Fan may fall if not assembled as directed in these Canopy (with Washer) installation instructions. Canopy Trim Ring Adapter Set Screw Indent Steps 3-5 – 3-6 Hunter Fan Company 42027-01 • 12/09/05...
Page 7
You will remove it after the last step on page 13. (Not Actual Size) Hook Hanger Bracket Round Hole Low Profi le Washer Step 3-11 Step 3-10 (Detail) 42027-01 • 12/09/05 Hunter Fan Company...
CAUTION: Be sure no bare wire or wire strands are visible after Wire Nut making connections. 4-6. Push all wires and wire nuts back into the hanger bracket. Hunter Fan Company 42027-01 • 12/09/05...
2. Press fi rmly on opposite sides of the ring towards the canopy. e tabs will fl ex out releasing the trim ring from the canopy Step 5-3 Steps 5-4 – 5-5 Canopy Screw 42027-01 • 12/09/05 Hunter Fan Company...
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, Step 6-1 (Detail) insert them by hand into the holes on the blades.
Housing Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. is feature gives you the option of installing the fan with OR without the included light fixture.
Page 12
#6-32 x 3/8” housing assembly screws. You will Step 7-5 need to rotate the blade irons out of the way for each screw. Plug Connector Detail Housing Assembly Screw Step 7-6 Hunter Fan Company 42027-01 • 12/09/05...
Page 13
Insert the end of the fan pull chain between the hooks on the pull chain pendant. Pull tight to capture the link between the hooks. Repeat for light pull chain. Pipe Glass Bowl Pull Chain Cap Finial Steps 4 – 6 42027-01 • 12/09/05 Hunter Fan Company...
Page 14
Nut and Insert the end of the fan pull chain between Washer the hooks on the pull chain pendant. Pull tight Lower to capture the link between the hooks. Switch Housing No-light Assembly Step 5 Hunter Fan Company 42027-01 • 12/09/05...
To Change Airfl ow Direction Turn the fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position. Restart fan. Reversing Switch 42027-01 • 12/09/05 Hunter Fan Company...
3. Turn power off , support fan very carefully, and check that the hanger ball is properly seated. If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 Hunter Fan Company 42027-01 • 12/09/05...