Hunter 42013-01 Installation And Operation Manual

Hunter fan fan user manual

Advertisement

Quick Links

42013-01 • 02/02/05

Advertisement

Table of Contents
loading

Summary of Contents for Hunter 42013-01

  • Page 1 42013-01 • 02/02/05...
  • Page 2: Table Of Contents

    • Read this entire manual carefully before beginning installation. Save these instructions. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied.
  • Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation fl exibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profi le, Standard, or Angle mounting.  e steps in this manual include instructions for all three Installer’s Choice mounting methods.
  • Page 4: Getting Ready

    • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
  • Page 5: Installing The Hanger Bracket

    For proper alignment use slotted holes directly across from each other. If you are installing the fan on an angled ceiling, be sure to orient the hanger bracket with the large opening towards the ceiling peak.
  • Page 6: Assembling And Hanging The Fan

    Leave the washer in place. (Note: You will not use the washer included in the parts sack.) 3-2. To assemble fan to hang down from a flat or angled ceiling, place the canopy with washer, and canopy trim ring around the adapter so that they rest on the fan assembly.
  • Page 7 3-10. Align the screw holes in the washer with the holes in the adapter. Assemble securely with three #8-32 x 1/2” screws. 3-11. Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy.
  • Page 8: Wiring The Fan

    4-1. Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. 4-2. Decide how you want to set up the fan and light controls. You can control the fan and/or lights together or separately using one or two wall switches.
  • Page 9: Installing The Canopy And Canopy Trim Ring

    2. Press fi rmly on opposite sides of the ring towards the canopy.  e tabs will fl ex out releasing the trim ring from the canopy 42013-01 • 02/02/05 5 • Installing the Canopy and Canopy Trim Ring Steps 5-1 – 5-2 Canopy Steps 5-4 –...
  • Page 10: Assembling The Blades

    Blade Mounting Screw Hunter Fan Company Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
  • Page 11: Installing The Light Kit

    WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two #6-32 x 3/8” housing assembly screws into the switch housing mounting plate. 7-2. Feed the upper plug connector through the center opening of the housing.
  • Page 12 Insert each glass shade in a shade cup. 7-8. Install and tighten the three thumb screws. Do not overtighten. 7-9. Install medium base incandescent light bulbs, maximum 60 Watt. Shade Cup Silencer Band Glass Shade 42013-01 • 02/02/05...
  • Page 13: Operating And Cleaning Your Ceiling Fan

    8-1. Turn on electrical power to the fan. 8-2.  e fan pull chain controls power to the fan.  e pull chain has four settings in sequence: High, Medium, Low and Off . • Pull the chain slowly to change settings.
  • Page 14: Troubleshooting

    1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade iron screws. 3. Turn power off , support fan very carefully, and check that the hanger ball is properly seated. If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com.

Table of Contents