Specifications - Integra DTR-30.5 Instruction Manual

Specifications

Amplifier Section
Rated Output Power
All channels: 95 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of
0.08% (FTC)
115 watts minimum continuous power
per channel, 6 ohm loads, 2 channels
driven at 1 kHz, with a maximum total
harmonic distortion of 0.7% (FTC)
(North American)
7 ch × 160 W at 6 ohms, 1 kHz, 1 ch
driven of 1% (IEC)
(Australian)
Maximum Effective Output Power
7 ch × 175 W at 6 ohms, 1 kHz, 1 ch
driven (JEITA) (Australian)
Dynamic Power *
* IEC60268-Short-term maximum output power
240 W (3 Ω, Front)
210 W (4 Ω, Front)
120 W (8 Ω, Front)
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz - 20 kHz, half power)
60 (Front, 1 kHz, 8 Ω)
Damping Factor
Input Sensitivity and Impedance (Unbalance)
200 mV/47 kΩ (LINE)
2.5 mV/47 kΩ (PHONO MM)
Rated RCA Output Level and Impedance
200 mV/470 Ω (PRE OUT/LINE OUT)
Maximum RCA Output Level and Impedance
4.6 V/470 Ω (PRE OUT/LINE OUT)
Phono Overload 70 mV (MM 1 kHz 0.5% Direct)
Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (Direct
mode)
Tone Control Characteristics
±10 dB, 30 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio 106 dB (LINE, IHF-A)
80 dB (PHONO MM, IHF-A)
6 Ω - 16 Ω (North American)
Speaker Impedance
4 Ω - 16 Ω (Australian)
Video Section
Input Sensitivity/Output Level and Impedance
1 Vp-p/75 Ω (Component Y)
0.7 Vp-p/75 Ω (Component P
P /C )
R R
1 Vp-p/75 Ω (Composite)
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz (North American)
87.5 MHz - 108.0 MHz, RDS (Australian)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel 40
Network Section
Ethernet LAN 10BASE-T/100BASE-TX
Wireless LAN
Compatible standards:
IEEE 802.11 b/g/n standard (Wi-Fi
standard)
Security: WEP 64 bit, WEP 128 bit, WPA/WPA2-
PSK (AES), WPA/WPA2-PSK (TKIP)
Transmission frequency
1 - 11 ch (North American)
1 - 13 ch (Australian)
(Wi-Fi ® standard)
Radio frequency 2.4 GHz
Bluetooth Section
Communication system
Bluetooth Specification version 2.1 +
EDR (Enhanced Data Rate)
Maximum communication range
Line of sight approx. 15 m
Frequency band 2.4 GHz band (2.4000 GHz –
2.4835 GHz)
Modulation method FHSS (Freq Hopping Spread Spectrum)
En-93
Compatible Bluetooth profiles
/C ,
B B
Supported Codecs
Transmission range (A2DP)
*1
The actual range will vary depending on factors such as
obstacles between devices, magnetic fields around a
microwave oven, static electricity, cordless phone,
reception sensitivity, antenna's performance, operating
system, software application, etc.
General
Power Supply
Power Consumption
No-sound Power Consumption
®
Stand-by Power Consumption
Dimensions (W × H × D)
Weight
■
HDMI
Input
Output
Video Resolution
Audio Format
*1
Supported
Appendix
A2DP 1.2 (Advanced Audio Distribution
Profile)
AVRCP 1.3 (Audio Video Remote
Control Profile)
SBC
20 Hz – 20,000 Hz (Sampling frequency
44.1 kHz)
AC 120 V, 60 Hz (North American)
AC 220 - 240 V, 50/60 Hz (Australian)
6.3 A (North American)
600 W (Australian)
85 W (North American)
240 V: 80 W
230 V: 70 W
(Australian)
0.15 W (North American)
0.2 W (Australian)
435 mm × 174.5 mm × 326.5 mm
17-1/8" × 6-7/8" × 12-7/8"
10.1 kg (22.3 lbs.) (North American)
10.3 kg (22.7 lbs.) (Australian)
IN 1, IN 2, IN 3, IN 4, IN 5, IN 6
OUT MAIN, OUT SUB
4K
Dolby TrueHD, DTS-HD Master Audio,
DVD-Audio, DSD
3D, Audio Return Channel, DeepColor,
x.v.Color, LipSync, CEC (RIHD), 4K (up-
scaling and Passthrough)