Panasonic SCMAX650 Owner's Manual page 14

The total number of tracks displayed is incorrect.
The disc cannot be read.
Distorted sound is heard.
• You put in a disc that the system cannot play. Change
to a playable disc.
• You put in a disc that has not been finalized.
Radio
Sound is distorted.
• Use an optional FM outdoor antenna. The antenna
should be installed by a competent technician.
A beat sound is heard.
• Switch off the TV or move it away from the system.
• When in AM tuner mode, select from "BP 1" to "BP 8"
that provides the best reception.
A low hum is heard during AM broadcasts.
• Move the antenna away from other cables and cords.
USB
Depending on the USB device, power may be supplied
to the USB device connected to USB A port when "USB
A" is selected.
The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it is/are
not compatible with the system.
• USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
Slow operation of the USB device.
• Large content size or large memory USB device takes
longer time to read.
Main unit displays
"A NO DEV"
"B NO DEV"
• The USB device is not connected. Examine the
connection.
"AC LOW"
• The household AC power supply is fluctuating. The
sound level of the system will reduce gradually to
protect the system.
"ERROR"
14
• An incorrect operation was done. Read the instructions
and try again.
"F61"
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and
then switch it on again.
"NO PLAY"
"UNSUPPORT"
• Examine the content. You can only play supported
format.
• The files in the USB device can be corrupted. Format
the USB device and try again.
"NO TRACK"
• There is no album or track in the USB device.
"NOT MP3 = ERROR"
• Examine the content. You can only play supported
format.
"PLAYERROR"
• You played an unsupported MP3 file. The system will
skip that track and play the next one.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using
different codes. Change the code of the remote
control.
– When "REMOTE 1" is shown, press and hold [OK]
and [1] for a minimum of 4 seconds.
– When "REMOTE 2" is shown, press and hold [OK]
and [2] for a minimum of 4 seconds.
"TEMP NG"
• The temperature protection circuit has been activated,
and the system will switch off. Let the unit cool down
before switching it on again.
• Check that the ventilation opening of the unit is not
obstructed.
• Ensure this unit is well ventilated.
"USB OVER CURRENT ERROR"
• The USB device is using too much power. Disconnect
the USB device, switch off the system and then switch
on again.
"VBR–"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Memory reset (initialization)
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
2
While you press and hold [1] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button
(approximately 10 seconds) until "– – – – – – – –" is
shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [RADIO, EXT-IN] (main unit: [EXT-IN]) to select
"MUSIC PORT" or "AUX".
To set the code to "REMOTE 2"
1
Press and hold [EXT-IN] on the main unit and [2]
on the remote control until "REMOTE 2" is
shown.
2
Press and hold [OK] and [2] for a minimum of 4
seconds.
To set the code to "REMOTE 1"
1
Press and hold [EXT-IN] on the main unit and [1]
on the remote control until "REMOTE 1" is
shown.
2
Press and hold [OK] and [1] for a minimum of 4
seconds.