Horizon Fitness GOAL GS 1035T User Manual page 5

P R E- ASSE MBLY
DO NOT ATTEMPT TO LIFT THE TREADMILL!*
WARNING
from packaging until specified to do so in the assembly instructions. Failure to do
so may result in injury! Remove plastic wrap from console masts.
NOTE:
During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware.
Any grease, such as lithium bike grease is recommended.
AS SE MB LY S TEP 1
HARDWARE BAG 1 CONTENTS :
LEFT CONSOLE MAST
WAVY WASHER (F)
FLAT WASHER (E)
BOLT (D)
LEFT LINKAGE ARM
BOLT (A)
FLAT WASHER
TEFLON WASHER
A Open HARDWARE BAG 1.
B Cut banding straps. Do not move or lift treadmill from packaging.
C Move LEFT LINKAGE ARM into position. Insert 1 BOLT (A) and 1 FLAT WASHER (B) into LEFT
LINKAGE ARM followed by 1 TEFLON WASHER (C) and attach to ELEVATION FRAME.
D Lift LEFT CONSOLE MAST into upright position. Be sure to hold the console mast firmly, as
it will not stay in the upright position on its own.
E Insert 1 BOLT (D) and 1 FLAT WASHER (E) through LEFT CONSOLE MAST followed by
1 WAVY WASHER (F) and attach to MAIN FRAME.
8
GS_1035T_Treadmill_Rev.2.3.indd 8-9
Do not move or lift treadmill
BOLT (A) FLAT WASHER (B) TEFLON WASHER (C)
15 mm 20 mm 18 mm
Qty: 1 Qty: 1 Qty: 1
BOLT (D) FLAT WASHER (E) WAVY WASHER (F)
Qty: 1 27 mm 29 mm
Qty: 1 Qty: 1
MAIN FRAME
(B)
(C) ELEVATION FRAME
ASS EMBLY STEP 2
HARDWARE BAG 2 CONTENTS :
BOLT (D)
Qty: 1
LEAD WIRE
RIGHT CONSOLE MAST
CONSOLE CABLES
ELEVATION FRAME CONSOLE CABLES
A ull LEAD WIRE through RIGHT CONSOLE MAST. After
P
pulling the LEAD WIRE through the mast, the top of the
CONSOLE CABLE should be located at the top of the
mast. Detach and discard LEAD WIRE.
B Open HARDWARE BAG 2.
C Move RIGHT LINKAGE ARM into position and attach to
ELEVATION FRAME.
NOTE: While holding RIGHT CONSOLE MAST in the
upright position, tighten PRE-ATTACHED BOLT using
T-wrench to attach RIGHT LINKAGE ARM.
D Insert 1 BOLT (D) and 1 FLAT WASHER (E) through
RIGHT CONSOLE MAST followed by 1 WAVY WASHER (F)
and attach to MAIN FRAME.
E Lift the RUNNING DECK until lock latch on side of
treadmill is fully engaged.
F Remove CONSOLE from box and place out of the way.
G Lower the treadmill RUNNING DECK from the folded
position by stepping on LOCK LATCH on lower right side.
FLAT WASHER (E) WAVY WASHER (F)
27 mm 29 mm
Qty: 1 Qty: 1
RIGHT CONSOLE MAST
MAIN FRAME
WAVY WASHER (F) FLAT WASHER (E)
BOLT (D)
RIGHT LINKAGE ARM
FOOT LOCK LATCH
PRE-ATTACHED BOLT
NOTE: If you have attempted to
move the treadmill from the box
and the machine has sprung
*
open and cannot be assembled,
refer to the troubleshooting
section in order to restore the
treadmill to its proper position.
1
3
2
9
6/13/07 11:18:12 AM