Dimplex DF3215 Service Manual page 4

Heat function On or press the Purifire™ On/Off button
to turn the Purifire™ function ON.
Frequency Interference
If the fireplace does not respond properly to the remote
control, the remote operating frequency may have to be
reset. The remote control can send another frequency code
to the circuit board to eliminate
interference.
1. Simultaneously press the "Slow Start" button and the
"Purifire™ Low Speed" button on the remote control.
2. "CODE" will appear.
3. Release the "Slow Start" button and the "Purifire™ Low
Speed" button.
4. Press and hold the initialization button on the unit.
5. Press the button on the remote and release the
initialization button.
Your remote will now have a different frequency
communicating with the fireplace.
Remote Control Functions (Figure 3)
Figure 3
2
7
9
4
11
13
15
6
17
1. Room Temperature
2. Set Temperature*
3. Dimmer
4. Flame Speed Control
5. Slow Start/Fading
Embers Control
6. Purifier™ Speed
7. Temperature Down*
8. Temperature Up*
9. Dimmer Down/
Firelight Off
1
8
3
10
12
14
5
16
18
10. Dimmer Up/Firelight
On
11. Flame Speed Down
12. Flame Speed Up
13. Slow Start/Fading
Embers Off
14. Fading Embers On/
Timer Cycle
15. Purifier™ Low Speed
16. Purifier™ High Speed
17. Flame & Heat On/Off
18. Purifier™ On/Off
2. Set Temperature*
1. Press 17. Flame Heat On/Off button to turn fireplace on.
2. Press 8. Temperature Up to raise thermostat.
3. Press 7. Temperature Down to lower thermostat.
4. Press both 8. Temperature Up and 7. Temperature
Down to change °F to °C.
!
* NOTE: The set temperature buttons are not operational
on the DF3215NH model fireplaces.
3. Light Dimmer Firelight
1. Press the 17. Flame/Heat On/Off button to turn the
Flame/Heat On.
2. Repeatedly press the 10. Light Dimmer Up or 9. Light
Dimmer Down button to decrease or increase the
brightness of the upper lights.
3. To activate the "Firelight", continue pressing 10. Light
Dimmer Up until the "Firelight On" icon
the display screen.
4. To shut the "Firelight" off, turn the 9. Light Dimmer
Down button until the "Firelight" icon off
the display.
4. Flame Speed
1. Press the 17. Flame/Heat On/Off button to turn the
Flame/Heat On.
2. Press the 12. Flame Speed Up to increase the speed of
the flame.
3. Press the 11. Flame Speed Down to decrease the speed
of the flame.
5. Slow Start / Fading Embers
The slow start function simulates a starting fire. The slow
start function is automatically programmed for 30 seconds.
The slow start timer setting cannot be changed. The fading
embers function simulates a fire going out. The fading
embers timer can be set to 1, 5 or 10 minutes.
1. Press the 14. Slow Start Fading Embers On button to
turn the Slow Start/Fading Embers function on.
2. Press the 14. Fading Embers On button repeatedly to
set the fading embers timer time to 1, 5 or 10 minutes.
3. Press the 13. Fading Embers Off button to turn the
Fading Embers timer function off.
6. Purifier™ Speed
Press the 18. Purifire™ On/Off button to turn the Purifire™
function On. When the Purifire™ function is On the
Purifire™ Speed symbol will flash. When off the symbol
will be solid. The default setting for the Purifire™ is set at
low speed. Press the 16. Purifier™ High Speed button
to switch to the high speed level and the Purifier™ Speed
symbol will flash more quickly. Press the 15. Purifier™ Low
Speed button to switch back to the lower speed, or Press the
18. Purifire™ On/Off button to turn the Purifire™ function
Off.
4
is shown on
is shown on