Gemini GEM-P9600 Installation Instructions Manual page 37

WI742E 2/04
Dial-Tone Detection
Skip Automatic Dial-Tone Detect
The panel features automatic dial-tone detection to ensure that a dial tone is present before the communicator dials. To skip this
feature, program an "8" in Location 4084.
When an "E" is programmed before the first digit of an outside telephone number, the communicator dial-tone detection circuit is
set to detect the standard 440Hz dial tone. The "E" is generally entered in the location immediately preceding the telephone number.
It may be necessary to program at least one 4-second pre-dial delay before a dial-tone detection "E". With certain nonstandard
exchanges, pre-dial delay "D"s may be used without a dial-tone detection "E". (See Access Number for Outside Line; Pre-Dial Delay;
Telephone Numbers.)
Digital Dialer Report Enter/Exit Test Mode
Initiation Report. At the initiation of a test, the control panel sends a message to the central station that a test is in progress. The
"Fault Find" function (a Function Menu selection) is enabled, and normally causes all zones to give a 7-second beep at the keypad(s)
when any zone is faulted or restored. As required by SIA CP-01, Fault Find is expanded with the following features when Digital Di-
aler Report Enter/Exit Test Mode is programmed. This option is programmed when "Enable CP-01 Feature" is selected in the Easy
Program Menu:
When Fault Find is entered, it reports to Central Station that "Test Mode" is in progress. On completion of the report, a Ring-
Back will be given.
Fault Find can not be initiated from an armed panel, and all digital dialer reporting is inhibited while in Fault Find.
Fault Find Central Station Reporting Code is located at address 0907.
Keypad will display the following warning that the system is in Fault Find: "FAULT FIND RF SIG POWER - - "
If 24-hour zone is open at end of test, no report is sent (GEM-P9600). If a 24-hour zone is tripped and not restored during
Fault Find, when the mode is exited the zone will display as "Faulted" on the keypad display.
When Fault Find is exited by pressing
Ring-Back will be given.
Digital Dialer Test
Activating the digital dialer test from the Function Menu (ACTIVATE DIALER TEST) will send the programmed report code to the
central station. Program DD TEST for SYSTEM-TROUBLE REPORTS and enter a DD TEST Report Code. Note that in this case
the report code received is not indicative of a system trouble, but is an indication of a successful transmission. Should the transmis-
sion fail, the keypad will display "E03-00 COMM FAIL". This system trouble may be reset by pressing the
subsequent report will also clear the system trouble.
Disable Answering Machine Download See Callback-Method Download
Disable Auto-Reset on Day Zone See Day Zone
Disable Zone Fault Scrolling (Auto Status)
Non 24-Hour Zones that are open (or shorted) normally display "ZONE FAULTS" (while disarmed) followed by the zone number(s)
and description(s). In high-security applications, program Disable Zone Fault Scrolling (Auto Status). Unsecured zones will then be
indicated by a "CHECK STATUS" display. Status may be displayed manually using the DISPLAY STATUS function, however a valid user
code will be required.
Disable Auto-Unbypass on Disarming
Normally, manually bypassed zones revert to active (disarmed) zones on disarming. Select this feature to maintain bypassed
zones on disarming until manually unbypassed.
Disable Call Waiting (TouchTone® Dialing Only)
A digital communicator connected to a telephone line with Call Waiting may be disrupted by this feature. However, most lines
with Call Waiting also have Selective Call Waiting, which permits the feature to be turned off by dialing a "*70" just before the tele-
phone number. A "*" will be dialed by programming a "B".
If the installation has the Call Waiting feature, be sure that it also has Selective Call Waiting, and confirm the disable code with
the telephone company. Then program this code ("B70") directly before the phone numbers (after dial-tone detection or pre-dial de-
lay) in the telephone-number locations. See Telephone Numbers.
Caution: Should the user cancel his Call Waiting service, the communicator will dial a wrong number unless the phone number
is corrected.
st
Disable Call Waiting on 1
st
Cancel "*70" after the 1 dial attempt. Default is disabled. When enabled, this option will dial the Central Station telephone number
as it is programmed in the panel. If the first communication is unsuccessful, the next and remaining dial attempts will remove the
star button (entered as a "B" from the keypad) and the 2 subsequent digits from the Central Station telephone number.
Disable Callback Download See Callback-Method Download
Disable Code Required for EZ Bypass See Selective Bypass (Do not program in UL Installations)
L
NAPCO Security Systems
(SIA CP-01 Requirement: 4.6.4.2)
, a Fault Find Restore Report will be sent, and upon completion of the report a
C
Attempt
(Address 3905, Bit 6)
C
X
GEM-P9600 Installation Instructions
!
Page 37
button. Any successful
*