Korg TRITON proX Manual page 8

0–1c: Program Information
Information on the selected program is displayed here. This
shows the functions that are assigned to the [SW1] and
[SW2] keys and to the B mode of REALTIME CONTROL
knobs [1], [2], [3], [4], and the names of the effects that are
selected for the insertion effects and the master effects.
0–1d: Performance Editor
The Performance Editor lets you edit major program param-
eters without moving to the Program P1–P9 Edit pages.
This edits multiple program parameters within the currently
selected program, allowing you to make broad adjustments
easily. You can use the Performance Editor when you wish
to adjust the depth of effects etc. while you are playing, or to
make the initial rough settings to begin the process of creat-
ing a new sound.
Editing that you do here will affect the values of the pro-
gram parameters in the edit buffer.
If you wish to keep the results of your editing, you must
write (save) the program ( p.38 in the Basic Guide ).
Editing done by the Performance Editor takes place
within the valid range of the applicable parameters. If
you use the Performance Editor to modify a value, then
move to another page or mode, and finally return to
Program mode, the previously-edited state will be
maintained, but the Performance Editor sliders in the
LCD screen will return to a value of +00 .
Since the Performance Editor is provided as a way of
making approximate edits, the balance between param-
eters may be lost in some cases.
If the "Enable Exclusive" (Global P1: 1–1b) setting is
checked, MIDI exclusive parameter changes will be
transmitted whenever you operate the Performance
Editor. If these messages are received by a TRITON
whose "Enable Exclusive" setting is checked, the Per-
formance Editor corresponding to that message will be
modified.
Octave
An adjustment of +01 will raise the pitch one octave.
An adjustment of –01 will lower the pitch one octave.
However, this setting cannot adjust the pitch higher than 4'
(feet) or lower than 32' (feet).
Pitch Stretch
This simultaneously adjusts the Transpose and Tune of the
oscillator. This lets you produce a variety of tonal changes
and variations without loosing the character of the original
sound.
At the +00 setting, the value of the program parameters will
be unchanged.
An adjustment of +01 will lower the Transpose value by 1,
and simultaneously raise the Tune value by 100.
An adjustment of –01 will raise the Transpose value by 1,
and simultaneously lower the Tune value by 100.
However, it is not possible for the Transpose value to exceed
the range of ± 12, nor the Tune value to exceed the range of
± 1200.
This Performance Editor function cannot be used with
bank F .
2
OSC Balance
This adjusts the level balance between oscillators 1 and 2.
At the +00 setting, the value of the program parameters will
be unchanged.
Positive (+) settings will lower the oscillator 2 level.
With an adjustment of +10 , the oscillator 2 level will be 0.
The oscillator 1 level will not change.
Negative (–) settings will lower the oscillator 1 level.
With an adjustment of –10 , the oscillator 1 level will be 0.
The oscillator 2 level will not change.
Amp Level
This adjusts the amp level.
With an adjustment of +00 , the value of the program param-
eters will be unchanged.
Positive (+) settings will increase the amp level above the
value that was set.
With an adjustment of +10 , the amp level will be 127 (maxi-
mum).
Negative (–) settings will lower the amp level below the
value that was set.
With an adjustment of –10 , the amp level will be 0.
Attack Time
This adjusts the amp times of the filter EG and amp EG.
With an adjustment of +00 , the value of the program param-
eters will be unchanged.
Positive (+) settings will lengthen the attack times beyond
the values that were set.
With an adjustment of +10 , the attack times will be 90.
Negative (–) settings will shorten the attack times.
With an adjustment of –10 , the attack times will be 0.
Decay Time
[–03...00...+03]
This adjusts the Decay Time and Slope Time of the filter EG
and amp EG.
With an adjustment of +00 , the value of the program param-
eters will be unchanged.
Positive (+) settings will lengthen the Decay Time and Slope
[–12...+00...+12]
Time beyond the values that were set. With an adjustment of
+10, the times will be 99.
Negative (–) settings will shorten the Decay Time and Slope
Time. With an adjustment of –10, the times will be 0.
IFX Balance
This adjusts the "Wet/Dry" setting of insertion effects 1–5 as
a whole.
With an adjustment of +00, the value of the program param-
eters will be unchanged.
Positive (+) settings will raise the Wet levels above the pro-
gram setting, and lower the Dry levels. With an adjustment
of +10, the setting will be "Wet."
Negative (–) settings will lower the Wet levels below the
program setting, and raise the Dry levels. With an adjust-
ment of –10, the setting will be "Dry."
MFX Balance
This adjusts the master effect "Return 1" and "Return 2" (9–
1c) settings as a whole.
With an adjustment of +00, the value of the program param-
eters will be unchanged.
For programs whose "Oscillator Mode" (1–1a) setting is
Single , oscillator 2 will not sound. Only the level of
oscillator 1 will change. For a Drums program, this per-
formance editor will have no effect.
When you modify "Attack Time," the EG Start Level,
Attack Level, Start Level Modulation, and Attack Time
Modulation of the amp EG will also be adjusted simul-
taneously, to allow the maximum effect to be obtained.
[–10...0...+10]
[–10...0...+10]
[–10...0...+10]
[–10...0...+10]
[–10...0...+10]
[–10...0...+10]