Korg TRITON proX Manual page 108

0–1(2)j: PLAY/MUTE, SOLO ON/OFF
PLAY/MUTE
This sets the play/mute status of each track. The setting will
alternate each time you press the PLAY/MUTE button.
PLAY: The track will play.
MUTE: The track will be muted.
SOLO ON/OFF
Switch the Solo function on/off. Only the track set to SOLO
ON will be heard. All other tracks will be muted.
If a track muted by the Mute or Solo function has a
"Status" (1–1a, 2a) of EXT or BTH, the MIDI note-on/
off messages of that track will not be transmitted.
(However, the track selected by "Play Track Select" (0–
1g) is an exception.)
If the page menu command "Solo Selected Track" (0–
1B) is ON, its solo settings will take priority (when ON).
When you press "SOLO ON/OFF" or press a parame-
ter of another track, only that track will be soloed and
will sound.
0–1: Page Menu Command
M
Parameter
P0 Bank/Program
Pan
Volume
P1 Status
Use Program's Scale
P7 Arpeggiator Assign
Other Arpeggiator parameters
P8 IFX/Indiv.Out BUS Select
Send1(MFX1)
Send2(MFX2)
IFX1–5
Pan(CC#8)
BUS Select
Send1
Send2
Other Insert Effect parameters
P9 MFX1
MFX2
Return1
Return2
Other Master Effect and Master EQ parameters
102
[PLAY, MUTE]
[SOLO ON, SOLO OFF]
0–1A
0–1B
0–1C
0–1D
0–1E
Track1–9, 11–16
G000:*A.Piano
C064
100
–
–
–
–
L/R
0
40
–
–
–
–
–
–
–
–
–
–
–
0–1A: GM Initialize
This command transmits a GM System On message to Song
Play mode, resetting all tracks to the GM settings (refer to
the table below).
In Song Play mode when a GM System On message is
received from an external device or if the SMF contains
a GM System On message, the tone generator will be
reset to the GM settings in the same way as when this
command is executed (However even in these cases, the
parameters of the P9: Master Effect will not be reset).
0–1B: Solo Selected Track
When you select this command and check the menu page,
only the selected track will sound and the remaining tracks
will be muted (the Solo function). To solo a different track,
select one of the parameters of that track ( Sequencer P0: 0–
1B).
If a track muted by the Mute or Solo function has a
"Status" (1–1a, 2a) of EXT or BTH, the MIDI note-on/
off messages of that track will not be transmitted.
0–1C: Load Template Song
This command loads a preset template song (one of sixteen
types P00–15) or a user template song (one of sixteen types
U00–15) into the song ( Sequencer P0: 0–1G).
0–1D: Save Template Song
This command saves the programs, the track parameters,
and the effect settings etc. as a user template song U00–15
( Sequencer P0: 0–1H).
The settings that are saved here can also be loaded in
Sequencer mode.
0–1E: Set Location
By pressing the [LOCATE] key you can move to the location
specified here ( Sequencer P0: 0–1J).
Track10
g(d)000:STANDARD KIT
C064
100
–
–
–
–
DKit
0
40
–
–
–
–
–
–
–
–
–
–
–
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
The setting remains unchanged
016: Stereo Chorus
053: Reverb Smooth Hall
127
050
Default settings