088: Phaser - Cho/Flng; (Phaser - Chorus/Flanger); 089: Reverb - Gate - Korg TRITON proX Manual

088: Phaser – Cho/Flng
(Phaser – Chorus/Flanger)
This effect combines a mono-type phaser and a chorus/
flanger.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Phaser Chorus/Flanger
+
Phaser
EQ
LEQ HEQ
Trim
Phaser
Resonance Feedback
Wet / Dry
Right
LFO: Tri / Sine
LFO: Tri / Sine
[P] LFO Frequency [Hz]
Sets the LFO speed
a
LFO Waveform
Selects LFO Waveform
[P] Manual
Sets the frequency to which the effect is applied
Depth
b
Sets the depth of LFO modulation
Resonance
Sets the resonance amount
[P] Phaser Wet/Dry
c
Sets the phaser effect balance
[F] LFO Frequency [Hz]
Sets the LFO speed
d
LFO Waveform
Selects LFO Waveform
[F] Delay Time [msec]
Sets the delay time
Depth
e
Sets the depth of LFO modulation
Feedback
Sets the feedback amount
[F] EQ Trim
f
Sets the EQ input level
[F] Pre LEQ Gain [dB]
Sets the gain of Low EQ
g
Pre HEQ Gain [dB]
Sets the gain of High EQ
[F] Cho/Flng Wet/Dry
Sets the effect balance of the chorus/flanger
h
Output Mode
Selects the output mode for the chorus/flanger
Wet/Dry
Sets the balance between the effect and dry sounds
Src
i
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
Wet / Dry
Chorus/Flanger
Normal
+
Output Mode
–
Wet Invert
Cho/Flng
Wet / Dry
Wet / Dry
0.02...20.00Hz
Triangle, Sine
0...100
0...100
–100...+100
Fx:023
–Wet...–2:98, Dry, 2:98...Wet
Fx:010, 023
0.02...20.00Hz
Triangle, Sine
0.0...50.0msec
0...100
–100...+100
Fx:020
0...100
–15...+15dB
–15...+15dB
–Wet...–2:98, Dry, 2:98...Wet
Fx:010, 020
Normal, Wet Invert
Fx:060
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
089: Reverb – Gate
This effect combines a mono-type reverb and a gate.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Reverb
EQ Trim
+
Pre Delay Reverb
LEQ HEQ
Right
Input Reverb Mix
Input
Envelope - Control
Gate+Dmpr D-mod
Envelope Select
[R] Reverb Time [sec]
Sets the reverberation time
a
High Damp [%]
Sets the damping amount in the high range
[R] Pre Delay [msec]
b
Sets the delay time of the reverb sound and gate control signal
[R] EQ Trim
c
Sets the EQ input level
[R] Pre LEQ Gain [dB]
Sets the gain of Low EQ
d
Pre HEQ Gain [dB]
Sets the gain of High EQ
[R] Reverb Balance
e
Sets the reverb effect balance
[G] Envelope Select
Switches between modulation source control and input signal control
f
Src
Selects the modulation source that controls the gate when Envelope
Select is set to D-mod
[G] Input Reverb Mix
Sets the balance between the dry and reverb sounds of the gate con-
trol signal.
g
Threshold
Sets the gate threshold level
[G] Polarity
h Switches between non-invert and invert of the gate on/off state
[G] Attack
Sets the attack time
i
Release
Sets the release time
Wet/Dry
Sets the balance between the effect and dry sounds
Src
j
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
f: Envelope Select, f: Src, g: Input Reverb Mix, g: Threshold
The "Envelope Select" parameter enables you to select whether
turning the gate on and off is triggered by the input signal level or
controlled directly by the modulation source. You can select from
Off to Gate2+Dmpr for the Src parameter to specify the modula-
tion source.
When "Envelope Select" is set to Input, the gate is controlled by
the level of signals that are the combination of the dry sound and
the reverb sound. When the signal level exceeds the threshold, the
gate opens and the reverb sound is output.
Normally, set "Input Reverb Mix" to Dry (the gate is controlled
only by the dry sound). If you wish to extend the gate time, set the
"Input Reverb Mix" value higher and adjust the "Threshold"
value.
Wet / Dry
Gate
Reverb
Balance
Wet / Dry
Gate
0.1...10.0sec
0...100%
0...200msec
0...100
–15...+15dB
–15...+15dB
Dry, 1:99...99:1, Wet
D-mod, Input
Off...Gate2+Dmpr
Dry, 1:99...99:1, Wet
0...100
+, –
Fx:005
1...100
Fx:005
1...100
Fx:005
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
199