3-4: Filter1 Eg - Korg TRITON proX Manual

Intensity to B
Specify the depth and direction of the effect that "AMS" will
have on filter 1B ( "Intensity to A").
3–3b: LFO 2
Adjust the depth of the cyclic modulation applied by OSC1
LFO2 (set by "OSC1 LFO2" 5–2) to the cutoff frequency of
filters 1A and 1B ( "LFO 1" 3–3a).
Intensity to A
Intensity to B
JS–Y Intensity to A
JS–Y Intensity to B
AMS (Alternate Modulation Source)
[Off, (PEG, FEG, AEG, KT, EXT)]
Intensity to A
Intensity to B
3–3: Page Menu Command
M
"0–1A: Write Program," "1–1A: Copy Oscillator," and "1–
1B: Swap Oscillator."
3–4: Filter1 EG
Here you can make settings for the EG that will produce
time-varying changes in the cutoff frequency of filters 1A
and 1B.
The depth of the effect that these settings will have on the
filter 1 cutoff frequency is determined by "Filter EG" (3–2b).
3–4a
3–4b
3–4a: Filter1 EG
Specify the time-varying change produced by the filter 1 EG.
Level:
The result will depend on the filter that was selected in "Fil-
ter Type" (3–1a). For example with the Low Pass Resonance
filter, positive (+) values of EG Intensity will cause the tone
to be brightened by positive (+) levels, and darkened by
negative (–) levels.
Start (Start Level)
Specify the change in cutoff frequency at the time of note-on.
Attack (Attack Level)
Specify the change in cutoff frequency after the attack time
has elapsed.
Break (Break Point Level)
Specify the change in cutoff frequency after the decay time
has elapsed.
[–99...+99] Sustain (Sustain Level)
Specify the change in cutoff frequency that will be main-
tained from after the slope time has elapsed until note-off
occurs.
Release (Release Level)
Specify the change in cutoff frequency that will occur when
the release time has elapsed.
Time:
These parameters specify the time over which each change
[–99...+99]
will occur.
[–99...+99]
Attack (Attack Time)
[–99...+99]
Specify the time over which the level will change from note-
[–99...+99]
on until the attack level is reached.
Decay (Decay Time)
[–99...+99]
Specify the time over which the level will change from the
attack level to the break point level.
[–99...+99]
Slope (Slope Time)
Specify the time over which the level will change after the
decay time has elapsed until the sustain level is reached.
Release (Release Time)
Specify the time over which the level will change after note-
on occurs until the release level is reached.
The specified
cutoff
frequency
3–4
3–4b: Level Modulation
These settings let you use alternate modulation to control
the "Level" parameters of the filter 1 EG.
3–4c
AMS (Alternate Modulation Source)
Select the source that will control the "Level" parameters of
the filter 1 EG ( p.210 "AMS (Alternate Modulation Source)
List").
Intensity
Specify the depth and direction of the effect that "AMS" will
have.
For example if "AMS" is Velocity, and you set "St," "At"
and "Br" to + and set "Intensity" to a positive (+) value, the
EG levels will rise as you play more strongly. If "Intensity"
is set to a negative (–) values, the EG levels will fall as you
play more strongly.
With a setting of 0, the levels specified by "Filter 1 EG" (3–
4a) will be used.
[–99...+99]
St (Start Level)
Specify the direction in which "AMS" will affect "Start (Start
Level)." When "Intensity" has a positive (+) value, a setting
[–99...+99]
of + for this parameter will allow "AMS" to raise the EG
level, and a setting of – will allow "AMS" to lower the EG
level. With a setting of 0 there will be no change.
[–99...+99]
Note-off
Sustain Level
Attack Level
Note-on
Break
Point
Level
Start
Level Attack Decay Slope Release
Time Time Time Time
[–99...+99]
[–99...+99]
[00...99]
[00...99]
[00...99]
[00...99]
Release
Level
Time
[Off, (KT, EXT)]
[–99...+99]
[–, 0, +]
15