Table of Contents
Advertisement
27
Timer Recording Wtth the VCR Plus+ Programming
System
POWER
Button_
VCR PLUS+/-
ENTER
Button
STATUS/-
EXIT
Button
Number -
Buttons
Button
MENU
Button
Remote Control
• If you pre._sthe VCR PLUS+/ENTER but-
ton at step 1, the VCR Plus+ Initial Screen
of the TV GUIDE Plus+ system will
appear if you have completed the TV
GUIDE Plus+ setup. In this case, follow
the steps in VCR Plus+ Recording section
of the separate TV GUIDE Plus+ manual.
• If CODE ERROR appears at step 2 a32er
you enter the PlusCode programming
number, the number you entered was
incorrect (for example, too short), lf this
happens, enter the correct number.
• CLASH mayflash on the screen at step 2.
This means that the timer recording you
just programmed and another timer
recording overlap, and thus the current
timer recording will not be carried out.
• To exit the VCR Plus+ programming sys-
tem at any time, press the STATUS/EXIT
button. The display will disappear from
the TV screen.
• If the preset time for a timer recording
comes up during an OTR, the OTR has
priority.
• To stop a started timer recording, press the
STOP/EJECT button on the VCR.
• lfthe power fails for more than one hour,
programmed timer recordings may be lost.
When you use the VCR with the auto
clock function set to OFF, repeat the
steps on page I0 before re-programming
the timer recording(s).
• Entering the TV GUIDE Plus+ system
during a recording will cancel the
recording.
See page 49 for more notes.
When you do not use the TV GUIDE
Plus+ system, follow the steps below to
program a timer recording using
PlusCode programming numbers.
Before you begin, make sure:
• Channels have been programmed.
• Guide channel numbers and user chan-
nel numbers have been programmed.
• The clock has been set.
• There is a tape in the VCR. Make sure
the tape's record tab is intact and the
tape is long enough to record the pro-
gram(s).
• The VCR is in VCR position.
• You have selected CABLE TV or TV
at the TUNER SET UP menu.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
1
Press the VCR PLUS+/ENTER button
on the remote control. The on-screen
display shown below will appear.
P, u s Co0_ .... -j
END PUSH EXIT
i2
i Press the Number buttons for the
i PlusCode programming number of the
program you wish to record (this number
: is different for every program, and it can
be four to eight digits long). Finally,
i press the VCR PLUS+/ENTER button.
/vvc_ P LU_ P._.
1
PLUS CODE: 1328_] _5.--
TO SET PUSH VCR +
• TO CORRECT PUSH CLEAR
END PUSH EXIT
To record the program once, press the
": Number 1 button to select ONCE. To
:
record the same program every day from
:
Monday through Friday, press the
:
Number 2 button to select DAILY. To
:
record the same program every week on
the same day (such as every Saturday),
:
press the Number 3 button to select
! WEEKLY.
4
Press the Number 1 button to record in
SP speed, press the Number 2 button to
record in LP speed, or press the Number
3 button to record in SLP speed. For
details, see page five. You cannot use
the (Tape) SPEED button at this time.
/'_ET,ME
_._.
1
[
PROGRAM
1
I
CHANNEL
09
I
TIME ON
10:30 PM
I
TIME OFF
11:30 PM
END PUSH EXIT
5
Press the STATUS/EXIT button. PRO-
GRAM WAS COMPLETED / PLEASE
TURN OFF VCR FOR TIMER
RECORDING should appear on the
screen. After three seconds, the on-
screen display will disappear.
6
To program additional timer recordings,
press the VCR PLUS+/ENTER
button
and repeat steps 2 - 5. When you are
finished, go to step 7.
7
Turn off the VCR power. The Timer
light will appear. The Timer light will
flash if there is not a tape in the VCR.
The VCR must be turned off for a
timer recording
to take place.
If you
forget to turn the VCR off, PLEASE
TURN OFF VCR FOR TIMER
RECORDING
flashes on your TV
screen two minutes before a timer
recording starts. You can remove it by
pressing the CLEAR button.
The VCR must be
off for a timer
recording to take
place! Make sure
there is a tape in
the VCR.
Advertisement
Table of Contents
