Table of Contents
Advertisement
7
Turning
on Your VCR
°°°_°°_**°°°°°o*-°°°°°**o°°°_°°o*o°°°°°°°°°°o°_o0e_o**°°°°°o°°o****°°°°°°°ooIeeeeee*oo*eoee_I_ee*otQ°moeeeee*eeIo**e*eeeoee*oee_e_o
TV and
VCR
Set the TV to channel
3 or 4, whichever
channel the CH3/CH4
switch on the back of
the VCR is set to.
/
Press the VCR button,
then the POWER
button.
3
Press the Number
1
button for English on-
screen displays or the
Number 2 button for
Spanish on-screen
dis-
plays.
€5&6
®
-
O
_000
00®®
®OQ®
oooo
-_
Paress the MENU
ton.
Press the CH(annel)
Up
button.
Remote Control
oe
•
ee
•
oeoeee
oe
•
oeeoooe
•
eoeoo
eeooeoeooeeeoeoooeeoeeooee
eeeeeoeeooeoeee
"
eeooe
• Whenyoupress
the POWER
button on the VCR to turn onthe
VCR_ the
remote control will beep. Press any button
on the remote control
to stop it.
LOCATING
REMOTE
will appear
on-screen
for almost
30 seconds.
See
page 38for
details.
• lfyou
do not see any on-screen
displays
when you turn on the VCR, repeat
the steps under "Hooking
Up Your VCR" on page six, then try again.
If
you still do not see any on-screen
displays, follow
the steps under "Channel
Memory'"
on page 28 and "Language
Selection"
on page 30.
• To skip this feature
andplay
a tape immediately,
insert a tape with its
record tab removed.
Playback
will start immediately.
Or, to skip step 3,
press the MENU button.
All on-screen
displays
will be in English.
To skip
step 5, press the STOP button.
Channels
will not be programmed,
and
TUNER
NOT SET will appear
on-screen.
• To program
channels
or to change
the language
at a later time, follow
the
steps on pages 28 and 30.
• lfyou
try to program
channels
when there is no antenna
or cable connected
to the VCR, programming
will appear to take place, but eventually
a NO TV
SIGNALS
message
will appear on-screen.
Connect
an antenna
or cable to
the VCR and try again.
You may need to follow
the steps on page 28.
• You cannot program
channels
ifa cable converter
box is connected
to a
VCR that is connected
to a TV. lf you have this kind of connection,
see
page 44for
details.
• Follow the steps on this page only when you plug the VCR power cord into
the wall outlet for the first time.
• The VCR distinguishes
between
standard
TV channels
and cable channels.
If you change
to TV or CABLE
TV mode, follow
the steps under "Channel
Memory"
on page 28.
i
Before turning
on your VCR, make sure
: there are batteries
in the remote control
and
the VCR and TV are connected
(see pages
:
five and six).
!1
• Turn the TV on. Set it to the same channel
:
as the CH3/CH4
switch on the back of the
VCR.
2
Press the VCR button, then the POWER
button on the remote control. The VCR
light will appear on the display panel and
the language select display screen shown
below will appear.
SELECT PUSH NO, SHOWN_
1 ENGLISH
ON
I
2 ESPANOL
/
E SELECTION OR
]
H MENU TO CONTINUE/
Press the Number 1 button to select English
on-screen displays or the Number 2 button
to select Spanish on-screen displays.
4
Press the MENU
button.
The channel pro-
i
gram display
shown below will appear.
The
i
display
will disappear
after about 60 sec-
i
onds if you do not press any buttons.
i,'_NNECT
ANTENNAOR CABLE_ k
I °vc"
/
THEN-.
/
I uS"c"uP * /
!5
: Press the CH(annel)
Up button to begin auto-
•_ matic channel
programming.
AUTO SET
: PROCEEDING
PLEASE
WAIT will appear
: on-screen.
The VCR will place all of the
: channels
you receive into its memory,
so
: when you scan through
channels
using the
i
CH(annel)
Up/Down
buttons,
you'll
only scan
: through
channels
that you receive.
The chan-
:
nel numbers
will appear briefly
on the display
i
panel.
When all channels
are programmed,
:
AUTO SET COMPLETED
will appear on-
screen briefly.
Then the TV GUIDE
Plus+ set
i
up screen appears
automatically.
Follow the
! steps in TV GUIDE
Plus+ Setup section of the
i
separate
TV GUIDE
Plus+ manual.
Advertisement
Table of Contents
