Table of Contents
Advertisement
24
Timer Recording
With VCR Plus+
Read steps 1-7 to program a timer
recording using VCR Plus+ numbers.
Before you begin make sure:
:_ Channels
have been programmed.
@ The clock has been set.
There is a tape in the VCR (make
sure the tape's record tab is intact
and the tape is long enough to record
the program(s).
The VCR is in VCR position.
O You have selected CABLE
TV or
TV at the TUNER
SET UP menu.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
Press the VCR Plus+ button on the
remote control.
The on-screen
display
shown below will appear.
_VCR
PLUS+
PROG
1
PLUS CODE
: L
K,_
END PUSH MENU
j
2
Press the Number buttons for the VCR
Plus+ number of the program you wish
to record (this number is different
for
every program).
Finally, press the
VCR Plus+ button.
VooCpR LUS+ PROG
"_
LUS
CODE
: 13285 _'
/
J
TO SET PUSH VCR
+
CORRECT
PUSH CLEAR
"_T_.O END PUSH MENU
3
To record the program
once, press the
Number
I button to select ONCE.
To
record the same program every day
from Monday through Friday, press the
Number
2 button to select DALLY. To
record the same program every week
on the same day (such as every
Saturday),
press the Number
3 button
to select WEEKLY.
Press the Number
1 button to record in
SP speed, or press the Number 2 but-
ton to record in SLp speed.
For
details, see page five.
You cannot use
the (Tape) SPEED
button at this time.
NE TIME
PROGRAM
1
PROGRAM
1
CHANNEL
09
TIME ON
10:30 PM
TIME OFF
11:30 PM
REC SPEED
SLP
P_I
LP--_
TUE.
_OEND
PUSH
MENU
5
Press the MENU
button.
PROGRAM
WAS COMPLETED
/ PLEASE
TURN
OFF VCR FOR TIMER
RECORDING
should appear on the screen.
After
three seconds, the on-screen
display
will disappear.
If needed, press the VCR Plus+ button
and repeat steps 2 to 5. When you are
finished,
go to step 7.
Turn off the VCR power. The Timer
light will appear. The VCR must he
turned off for a timer recording to
take place. If you forget to turn the
VCR off, PLEASE TURN OFF VCR
FOR TIMER RECORDING
flashes
on your TV screen two minutes before
a timer recording starts. You can
remove it by pressing the CLEAR but-
ton.
POWER
Button
--
The VCR
must be off for a
timer recording
to take place!
VCR
Plus+
Button
CLEAR
Button
MENU
Button ---[--
Number
Buttons
Remote
Control
_-._...J[[ > I)LY-
O (D C_
O®C
®®C
•
***************************°°******°.°***
°°
Qo
--
TES
,.;;
• If CODE ERROR
appears
at step 2
after you enter the VCR Plus+ numbel;
the number
you entered was incorrect
(for example,
too short),
lf this hap-
i
pens, waitfive
seconds,
then enter the
•
correct number.
• To quit VCR Plus+ programming
at
any step, press the MENU button.
The
on-screen
display
will disappear
from
•
the TV screen.
• Cancel a VCR Plus+ timer recording
just like you would cancel a regular
timer
recording
(see
poge
20
for
details).
• To stop a started timer recording,
press
the POWER
button on the VCR.
• lfthe
power fails for more than three
secondx,
programmed
timer
recordings
may be lost. If this case, repeat the
steps on pages seven and ten before re-
programming
the timer recordings.
See page 42 for more notes.
Advertisement
Table of Contents
