Page 1
VR401BMX VR601BMX ideo Cassette Recor ideo Cassette Recor Owner’ s Manual Owner’ s Manual...
Page 2
As a member of the Magnavox “family,” you’re entitled to protection by one of the most comprehensive warranties and outstanding ser- vice networks in the industry.
Welcome to your VCR owner’s manual. This manual describes the VR401BMX and the VR601BMX. The VR401BMX is a monaural (single sound source) system, while the VR601BMX is a stereo system. Otherwise, the two models are exactly the same. In this manual, the VR601BMX is illustrated. (The VR401BMX has single AUDIO IN/OUT jacks. Otherwise, the VR401BMX looks exactly like the VR601BMX.)
Putting Batteries in the Remote Control Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow. Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. Replace the battery compartment lid.
TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. (The VR601BMX is illustrated here. The VR401BMX has single AUDIO IN/OUT jacks.) Disconnect the antenna or cable from your TV.
Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7 Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.) Antenna or Cable...
8 Hookups With a Cable Box/Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: You may view any channel. You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR. You may not view a channel other than the one you are recording.
Hookups With a Cable Box/Direct Broadcast System (cont’d) 9 With this connection: You may watch one channel while recording another. You may not record scrambled channels. AUDIO VIDEO CH3 CH4 Cable Signal RF coaxial cable Connections Connect a Cable signal to the VCR’s ANT(enna) IN Jack. Use an RF coaxial cable (supplied) to connect the OUT Jack on the VCR to the IN Jack on the Cable Box/DBS.
AUDIO IN Jacks on your TV, again matching cable colors to the jack colors. VR401BMX: Connect an audio cable to the white AUDIO OUT Jack on the back of the VCR. Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV.
Before turning on your VCR, make sure batteries are in the remote control and the VCR and TV are connected correctly. You can not program channels if you are using a Cable Box or a Direct Broadcast System. Press the POWER button. The VCR/TV light and the POWER light will appear on the display panel.
12 Automatic Channel Setup Although your VCR may automatically memorize the channels you receive when you turn it on for the first time, this function lets you set up the channels again. Press the MENU button. SELECT op CHOOSE B PROGRAM VCR SET UP TUNER SET UP...
Adding/Deleting Channels Press the MENU button. Press the PLAY/o button or the STOP/p button to select TUNER SET UP, then press the F.FWD/B button. Press the PLAY/o button or the STOP/p button to select ADD/DELETE CH, then press the F.FWD/B button. SELECT op ADD/DELETE B DELETED DELETED...
14 Automatic Channel Setup (cont’d) Reviewing Memorized Channels Press the MENU button. SELECT op CHOOSE B PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT Press the PLAY/o button or the STOP/p button to select TUNER SET UP, then press the F.FWD/B button. SELECT op CHOOSE B AUTO PROGRAMMING ADD/DELETE CH...
Follow the steps below to set your VCR’s clock. Make sure: The VCR is on and the VCR/TV light appears on the display panel. (If it does not, press the VCR/TV button once.) You make each entry within 60 seconds of the previous entry. Press the MENU button.
16 Daylight-Savings Time You may program the VCR so its clock will automatically move forward one hour in April and turn back one hour in October. Daylight-Savings Time is set to ON when you receive your VCR. Turn Daylight-Savings Time ON or OFF by following the steps below.
Follow the steps below to change the language of the on-screen displays and menus. Press the MENU button. SELECT op CHOOSE B PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.
18 Remote Control Buttons Press to select channels at the VCR. Use to set up VCR features (such Enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay.
Page 19
Use to select the signal that your TV receives. Use to watch a tape, to watch a program while recording it, or to watch a TV broadcast using the CHANNEL o/p or Number buttons to change channels at the VCR. If the VCR/TV light appears on the dis- play panel of the VCR, it is in VCR position.
20 On-Screen Status Displays A status display will appear when you press the STATUS/EXIT but- ton or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds.
Cassette Compartment Insert a tape here. VR601BMX VIDEO L - AUDIO -R POWER POWER POWER Light This light appears when the power is on. VCR/TV Light This light appears when the VCR is in VCR position. This light does not appear when the VCR is in TV position.
VCR, or an audio source here. Details are on page 32. The VR601BMX is shown here. The VR401BMX has only one AUDIO IN jack. VCR/TV Button Press to select VCR or TV position. VCR Position...
Connect audio cables going to the AUDIO IN Jacks of a camcorder, another VCR, or an audio system here. Details are on pages 32 and 38. The VR601BMX is shown here. The VR401BMX has only one AUDIO OUT jack. Rear Panel 23...
24 Playing Read and follow the steps below to play a tape. Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to. Insert a tape in the VCR. The POWER, VCR/TV and CST. IN lights will appear on the display panel.
Read and follow the steps below to record a television program. Turn on the TV and set it to channel 3 or 4, whichever channel the CH3/CH4 switch on the back of the VCR is set to. Insert a tape with its record tab intact in the VCR. If the VCR/TV light appears on the display panel, go to step 4.
26 Recording One Channel/Watching Another Press the REC(ord)/OTR button to start a recording of the current channel. (See page 25.) Press the VCR/TV button to put the VCR in TV position. The VCR/TV light will disappear from the VCR’s display panel. Use the TV remote control to select the channel you want to watch at the TV.
The One-Touch Recording (OTR) feature allows you to set an immediate timed recording 30 minutes to eight hours long. Before you begin: Set up the channels at the VCR. Select a recording speed (SP, SLP) with the SPEED button. Put a tape in the VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program(s).
28 Timer Recording Follow the steps below to program your VCR to record TV pro- grams while you’re away from home. The VCR will turn itself on, record, and turn itself off automatically. Before you begin: Set up the channels at the VCR. Set the clock.
Page 29
Use the Number buttons (1-8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen. NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly.
30 Timer Recording (cont’d) Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. (See the chart below.) You cannot use the SPEED button at this time. ONE TIME PROGRAM PROGRAM CHANNEL TIME ON...
Page 31
Checking or Cancelling Timer Recordings With the VCR on and in VCR position (the VCR/TV light will appear on the display panel), press the MENU button. Press the PLAY/o button or the STOP/p button to select PROGRAM, then press the F.FWD/B button. Press the PLAY/o button or the STOP/p button to select PROGRAM REVIEW, then press the F.FWD/B button.
Different VCRs may operate differently. • The VCR in the figure above is the VR601BMX. If you have the VR401BMX, use a single-plug audio cable to connect the AUDIO OUT jack on VCR 1 to the AUDIO IN jack on VCR 2.
Follow the steps below to make the VCR play a tape over and over. Press the MENU button. SELECT op CHOOSE B PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.
34 Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. Play, fast forward, or rewind a tape to the location that you would like to refer to later. Press the STOP/p button to stop the tape.
Follow the steps below to program the VCR to search forward or backward on a tape a specific length of time. There must be a tape in the VCR. Press the TIME SEARCH button. TIME SEARCH 0:00 ENTER SEARCH TIME Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward.
36 Special Effects Playback Forward and Reverse Searching (SP/LP/SLP) During tape playback, press and release the F.FWD/B button or the REWIND/{ button. A fast forward or reverse picture search will begin. To return to playback, press the PLAY/o button. Super High Speed Searching (LP/SLP) During tape playback, press the F.FWD/B button or the REWIND/{ button, then press again.
The following playback features will always operate. Automatic Playback When you put a tape in the VCR, the power will come on auto- matically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automati- cally when you insert a tape with the record tab intact.
38 Multi-Channel Television Sound System (VR601BMX only) Your VCR can play recordings broadcast in Hi-Fi (high fidelity) stereo, which produces a crisp, clear sound from two sources. Your VCR also can play tapes recorded in a second audio (usually, that means your program is recorded in a second language).
Page 39
Multi-Channel Television Sound System (VR601BMX only) (cont’d) 39 Press the MENU button. SELECT op CHOOSE B PROGRAM VCR SET UP TUNER SET UP SET CLOCK TO END PUSH EXIT Press the PLAY/o button or the STOP/p button to select TUNER SET UP, then press the F.FWD/B button. SELECT op CHOOSE B AUTO PROGRAMMING ADD/DELETE CH...
40 Hi-Fi Stereo Sound System (VR601BMX only) Multi-Channel Television Sound system broadcasts are automatically recorded in Hi-Fi stereo sound. To play in Hi-Fi stereo the tapes recorded in Hi-Fi stereo, however, you’ll need to follow steps 1-5. Press the MENU button. SELECT op CHOOSE B PROGRAM VCR SET UP...
If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACK- GROUND to OFF.
42 Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call.
Tape cannot be inserted. • Insert the tape, window side up, with the record tab facing you. • Make sure a tape isn’t already in the VCR by pressing the STOP/EJECT button on the VCR. • Gently push on the center of the tape when putting it in the VCR. Never force the tape into the VCR. •...
VCR which are used to record audio from another source (IN) or to send audio to another system (OUT). The VR401BMX has a single AUDIO IN jack on the front and back of the VCR. It has a single AUDIO OUT jack on the back of the VCR.
UPPLIED The following items are supplied with your VCR; they are provided to help you use or set up your VCR. Remote Control 4835 218 37274 Two AA Batteries 4835 138 17012 PTIONAL The following additional items are not provided with your VCR, but they are designed for use with your new VCR.