Marantz SR7005 User Manual page 76

ENGLISH DEUTSCH
Audio/Video Adjust
Setting items
Height Gain Low : Reduce the front height channel volume.
Control the front height Mid : Front height channel sound is output with standard sound volume.
channel volume. High : Increase the front height channel volume.
NOTE
"Height Gain" is displayed for the following settings.
• When "Amp Assign" (vpage 74) is set to "Normal".
• When the "Speaker Config." – "F.Height" setting (vpage 75) is set
other than to "None".
• When surround mode is "PLgz" or the PLgz decoder is used.
Default Yes : Reset to the defaults.
The "Surround Parameter" No : Do not reset to the defaults.
settings are returned to the
default settings.
n Tone
Adjust the tonal quality of the sound.
Setting items
Tone Control ON : Allow tone adjustment (bass, treble).
Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.
"Tone Control" can be set when "Dynamic EQ" (vpage 71) is set to
"OFF".
NOTE
• "Tone Control" settings are not reflected to ZONE2 and ZONE3.
• The tone cannot be adjusted in the direct mode.
Bass –6dB – +6dB
Adjust low frequency range
"Bass" can be set when "Tone Control" is set to "ON".
(bass).
Treble –6dB – +6dB
Adjust high frequency range
"Treble" can be set when "Tone Control" is set to "ON".
(treble).
70
Remote control operation
buttons
FRANÇAIS ITALIANO ESPAÑOL
Setting details
Setting details
Move the cursor
(Up/Down/Left/Right)
NEDERLANDS SVENSKA
n Audyssey Settings
Set MultEQ ® XT, Dynamic EQ ® and Dynamic Volume ® . These can be selected after Audyssey ® Auto
Setup has been performed. For additional information on Audyssey technology, please see page 105.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 11) to return to
the settings after Audyssey Auto Setup was run.
Setting items
MultEQ XT Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ XT front L and R speakers.
corrects both time and Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response response.
problems in the listening Manual : Apply frequency response set with "Manual EQ" (vpage 72).
area based on Audyssey OFF : Turn "MultEQ XT" equalizer off.
Auto Setup calibration. We
recommend "Audyssey".
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
MultEQ XT is the
selected after Audyssey Auto Setup has been performed. "Audyssey"
prerequisite function for
is automatically selected after performing Audyssey Auto Setup. When
Dynamic EQ and Dynamic
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected,
Volume.
illuminates.
• After running Audyssey Auto Setup, if the
Speaker Configuration, Distance, Channel
Level, and Crossover Frequency have changed
without increasing the number of speakers
measured, only
MULTEQ
• Pressing
NOTE
• "MultEQ XT" and "Manual" cannot be selected when "EQ Customize"
is set to "Not Used" (vpage 77).
• When using headphones, "MultEQ XT" is automatically set to "OFF".
Confirm the setting
Default settings are underlined.
Setting details
illuminates.
makes this setting.
Return to previous menu