Table of Contents
Advertisement
REMOTE CONTROL MODEL LR4455
AUTO FIND MODE
Use Auto Find to automatically find the brand code needed
to operate your equipment.
NOTE: If no button is pressed for 60 seconds or more
during Auto F'md, the remote will automatically exit Auto
Fred without
storing
any brand codes.
(LEDs
will [lash 3
timesupon exiting.)
1. Turn on the equipment you wish the remote to
operate.
2.
Press and hold LEARN
until mode indicator
lights
(about 4 seconds).
3.
Use MODE
to
select the mode you wish
to
program
(TV, VCR,
CABLE
or
AUX).
In the AUX
mode
Auto Find will search
through
all TV,
VCR and
Cable brand codes.
4.
Enter "00" then press ENTER
within 2 seconds.
All
four mode indicator lights will turn ON and then OFF,
leaving the mode indicator light for the active mode ON.
5.
Point remote towards
the equipment.
SPECIAL
PWR ON
EQUIPMENT
Point
toward
equipment
Learning
Remote
6.
Press and release OFF/ON
on the remote about once
every second,
until the equipment
turns OFF. Press
ENTER before pressing
any other buttons.
If you press OFF/ON
again before pressing ENTER
Auto Find will have to be repeated.
7.
Try other buttons
to see if they operate
the equip-
ment. If they do not, you may wish to reenter
Auto
Find and try to find another
code. The remote will
begin with codes starting from where it left off prior
to exiting Auto Find.
8.
Repeat Auto Find for each piece
of equipment
you
want your remote to operate.
NOTE:
Only one brand
code can be programmed
in each of the four modes.
If no brand code has been entered after searching
through
all brand codes in any mode, the LEARNING
remote will
flash all four mode indicator lights in a chasing manner.
Wait 60 seconds or press ENTER or LF_ARN to return to
normal operation.
ERASE
MODE
If you wish to erase learned functions or programmed
brand codes. You may.
A. Re-teach
a button.
B.
Erase learned
functions
from all buttons
in an
individual
mode.
C. Erase
learned
functions
from all buttons
and
erase all programmed
brand codes.
A. Any button
except
MODE and LEARN can be re.
taught-at
any time. See "Learning
Mode" section.
B.
To Erase
Learned
Functions
from All Buttons
in
an Individual
Mode
1.
Press
and hold LEARN
until mode indicator
lights
(about
4 seconds).
The mode indicator
light for the active mode will turn ON.
2.
Use MODE
to select
the mode from which all
learned
functions
are to be erased.
3.
Enter
one of the following
codes
to erase
all
learned
functions
in an individual
mode:
198 for "IV Mode
298 for VCR Mode
398 for CABLE Mode
498 for AUX Mode
Press ENTER within two seconds
of the last digit.
NOTE:
Any brand codes
programmed
into the
remote
will remain.
4.
All
four
mode
indicator
lights
will turn on
momentarily
to indicate
that all learned
func-
tions in the selected
mode have been erased
and
that you have left the Erase mode.
C. To
Erase
All
Learned
Functions
and
All
Programmed
Brand Codes
1.
Press
and hold LEARN
until mode
indicator
lights (about 4 seconds).
2.
Enter
"911"
then
press
ENTER
within
2
seconds.
3,
All four
mode indicator
lights
will turn ON
momentarily
to indicate
that the remote ha_ left
the Erase mode.
All learned
functions
and all
programmed
codes
have been erased.
The
remote
is now
programmed
with
the
default
Zenith
brand
codes
as received
from
the factory:
101 for "IV Mode
201 for VCR Mode
301 for CABLE Mode
330 for AUX Mode (Satellite)
_
6 - 8
Advertisement
Table of Contents
