Table of Contents
Advertisement
AUDIO MENU
AUDIO
SURROUND
U:e ADJUST (ADJ) I._ft/Right to select the speaker audio
output mode. You may choose either STEREO, MONO or
2ND AUDIO/SAP.
If STEREO is selected but not •
re_eive_ the following line appears at the bottom of the
menu:
THIS PROGRAM
IS NOT IN STEREO
If 2ND AUDIO/SAP
is selected but not received, the fol-
lowing line appeazs at the bottom of the menu:
THIS PROGRAM
HAS NO 2ND AUDIO
In either of these cases, the ChanneljTime display will al-
ways show what type of AUDIO signal is being received
and has been selected default.
If you choose STEREO,
you may want to enable Surround
sound by using the SURROUND
option.
SEQ (Spatial Equalization)
Use ADJUST (ADJ) Left/Right to turn SEQ ON or OFF.
SEQ improves tonal balance and increasesapparent stereo
separation
to produce a spacious and more natural sound.
Music and sounds appear to emanate from points outside
the television set, while dialogue is localized within the pic-
ture.
SEQ is only available if a stereo signal is being received and
you have previously selected STEREO using the AUDIO
option or if STEREO is selected by default.
If no stereo signal is being received, the words NOT
AVAILABLE appear next to SEQ, and the following fine
appears at the bottom of the menu:
THIS PROGRAM
IS NOT IN STEREO
If your AUDIO selection is either MONO or 2ND
AUDIO/SAP,
the words NOT AVAILABLE
appear next
to SEO and one of the following firms appear at the bottom
of the menu:
MONO
HAS BEEN SELECTED
2ND AUDIO
HAS BEEN SELECTED
Some weak or nonstandard signals may not be suitable for
SEQ, which may make imperfections
in the audio transmis-
sion more obvious. Turn SEQ off if this condition exists.
Use ADJUST (ADJ) Left/Right
to adjust the level of Sur-
round sound you wish to obtain. To decrease
(-)
Surround
sound, press ADJUST
(ADJ) Left. To increase ( + ) Sur-
round sound, press ADJUST
(ADJ) Right.
SURROUND
sound is only available if a stereo signal is
being re_k-._
and you have previously selected STEREO
using the AUDIO
option or if STEREO is selected by
default.
When SURROUND
is activated, "SURROUND
SPEAKERS REO_"
appears at the bottom of the
menu. This is a reminder that surround sound is only avail-
able when you have optional surround speakers connected
to the SURROUND
SPEAKER jack. The TV's internal
speakers do not produce surround sound.
If no stereo signal b being received, the words NOT
AVAILABLE
appear next to SURROUND,
and the fol-
lowing line appears at the bottom of the menu:
THIS PROGRAM
IS NOT IN STEREO
If your AUDIO selection is either MONO or 2ND
AUDIO/SAP,
the words NOT AVAILABLE
appear next
to SURROUND
and one of the following lines appear at -
the bottom of the menu:
MONO HAS BEEN SELECTED
2ND AUDIO HAS BEEN SELECTED
NOTES
I.
2.
Continuously
pressing
ADJ
Left
automatically
turns Surround
speakers
OFF.
If the current program is not in stereo,
you will not
be able to change
the SURROUND
option.
The
status display shows "THIS PROGRAM
IS NOT IN
STEREO."
3.
If Surround
speakers
are
not used,
set
SUR-
ROUND
option
to OFF
for optimum
stereo sound
reproduction.
4.
If you are in the SURROUND
menu option
and
press MUTE
on the remote
control,
only the Sur-
round speakers
are muted.
NOTE: If SEO is available, you can turn SEO ON or OFF
directly by pressing SEQ on the remote control.
10-2
Advertisement
Table of Contents
