Yamaha RX-V1700 Owner's Manual page 135

•
Bi-amplification
connection
A [_i-amplification connection uses two amplifiers for a
speaker. One amplifier is connected to the woofer section
of a loudspeaker while the other is connected to the
combined mid and tweeter section. With this arrangement
each amplifier operates over a restricted frequency range.
This restricted range presents each amplifier with a much
simpler .job and each amplifier is less likely to influence
the sound in some way. The internal crossover of the
speaker consists of a LPF (low pass filter) and a HPF (high
pass filter). As its name implies, the LPF passes
frequencies beh)w a cutoff and rejects frequencies above
the cutoff frequency. Likewise, the HPF passes
frequencies above its cutoff.
•
Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the Pt_
and PR signals for the chrominance. Color can be
reproduced more faithfiflly with this system because each
of these signals is independent. The component signal is
also called the "color difference signal" because the
luminance signal is subtracted fi'om the color signal. A
monitor with component input jacks is required in order to
output component signals.
• Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite
video.jack on a video component transmits these three
elements combined.
• Dialogue normalization
Dialogue Normalization is a feature of Dolby Digital or
DTS, which is used to keep the programs at the same
average listening level so the user does not have to change
the volume control between Dolby Digital or DTS
programs.
• Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
fi'ont channels (front L/R and center), and 2 surround
stereo channels, Dolby Digital provides 5 fifll-range audio
channels. With an additional channel especially for bass
effects, called LFE (Low Frequency Effect), the system
has a total of 5.1-channels (LFE is counted as 0.1
channel). By using 2-channel stereo for the surround
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range fi'om maximum to
minimum volume reproduced by the 5 full-range channels
and the precise sound orientation generated using digital
sound processing provide listeners with unprecedented
excitement and realism. With this unit, any sound
environment fi'om monaural up to a 5.1 -channel
configuration can be freely selected for your enjoyment.
• Dolby Digital EX
Dolby Digital EX creates 6 full-bandwidth output
channels fi'om 5.1 -channel sources. This is done using a
matrix decoder that derives 3 surround channels fi'om the
2 in the original recording. For the best results, Dolby
Digital EX should be used with movie sound tracks
recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and
realistic moving sound especially with scenes with "fly-
over" and "fly-around" effects.
• Dolby Pro Logic II
Dolby Pro Logic tl is an improved technique used to
decode vast numbers of existing Dolby Surround sources.
This new technology enables a discrete 5-channel
playback with 2 fi'ont left and right channels, 1 center
channel, and 2 surround left and right channels instead of
only 1 surround channel for conventional Pro Logic
technology. There are three modes available: "Music
mode" for music sources, "Movie mode" for movie
sources and "Game mode" for game sources.
• Dolby Pro Logic IIx
Dolby Pro Logic ttx is a new technoh)gy enabling discrete
multi-channel playback fi'om 2-channel or multi-channel
sources. There are three modes aw_ilable: "Music mode"
for music sources, "Movie mode" for movie sources (for
2-channel sources only) and "Game mode" for game
sources.
131 E.