Yamaha RX-V1700 Owner's Manual page 104

Zone 2 amplifier "::={",Mi::2.":= ,"M'di:::,
Zone 3 amplifier "::=""Mi::2":i= ,"H'di:::,
Use to select how the ZONE 2 and/or ZONE 3 speakers
are amplified.
Choices: EXT, [SP1], [SP2], BOTH
• Select "EX'I"' if you want to connect your Zone 2 or
Zone 3 speakers through an external amplifier
connected to the ZONE 2 OUTPUT or ZONE 3
OUTPUT .jacks on the rear panel of this unit.
• Select "[SPIt" m use the internal surround back
amplifier of this unit when you want to connect your
Zone 2 or Zone 3 speakers directly to the SP1 speaker
terminals on the rear panel of this unit.
• Select "[SP2]" to use the internal surround amplifier of
this unit when you want to connect your Zone 2 or
Zone 3 speakers directly to the SP2 speaker terminals
on the rear panel of this unit.
• Select "BOTH" to use the internal surround and
surround back amplifiers of this unit when you want to
connect your Zone 2 or Zone 3 speakers directly to
both the SP1 and the SP2 speaker terminals on the rear
panel of this unit.
• When "BI-AMP" is set to "ON" in the "ADVANCED SETUP"
menu, "ISPI}", "{SP2I" and "BOTH" cannot be selected.
• When "BOTH" is selected for "ZONE2 AMP", only "EXT" can
be selected for "ZONE3 AMP".
• When "BOTH" is selected for "ZONE3 AMP", only "EXT" can
be selected liar "ZONE2 AMP".
• When you set "ZONE2 AMP" or "ZONE3 AMP" to "[SPI I" or
"ISP2I" and the corresponding zone is turned on, no sound is
output Dora the surround back speakers.
• When you set "ZONE2 AMP" or "ZONE3 AMP" to "BOTH"
and the corresponding zone is turned on, no sound is output
It-ore both the surround speakers and the surround back speakers
in the main zone.
• When both "ZONE2 AMP" and "ZONE3 AMP" are set to
"{SPI 1" or "[SP2I" and Zone 2 and Zone 3 are turned on, no
sound is output from both the surround speakers and the
surround back speakers in the main zone.
• When you use internal amplifiers liar Zone 2 or Zone 3, some
surround field programs may not work in the same way as when
you do not use the internal amplifiers liar Zone 2 or Zone 3.
XM Radio setting "::: "=..,_.,.i D,......., i.,-, ,:::.i::.._-
(U.S.A. and Canada models only)
i=,/A,q,_i=1==i" T=== ==i=, =
IZ,7,=i'! F,_LJ.II.I 2_i
÷ Y,I,1I-GI,43EI41,41:I:, 1,4OI417
XM Radio antenna ..... i.,._ i"ii..r'i"_::'Mi..h"l
_"d I r"ll >I _ I,,,,I 'II ><q"_
Use this feature to check the current reception level of the
XM Passport System connected to the XM .jack of this
unit (see page 61). For the best reception, orient the XM
Passport System so that a vahte of 60% or more is
displayed here.
Display stares: NONE, 0 to 100%
• "NONE" is displayed if the XM Passport System is not connected to
this unit. in this case, check the antenna connections (see page 61 ).
• The "XM ANTENNA" parameter cannot be adjusted by using
the remote control. Instead, you need to adjust the orientation of
the XM Passport System connected to the XM jack of this unit
for a beucr percentage of the reception level.
• Dock set i..J .., r '.,i-u".i...' <::'i:::'"i"
i i,,' i,,,',,,._,,,,i',, .,,,_,,,
i ]' i_ 1%" i, ' ==i_ "_
FI,,'LJLiL, r,, 2_Ci
+ STIqI'4DI_',' C:IHI_IG _I:ILITL-I
[4 ]'[ _] := S el ect
[ EIJTER] :Ret caJ f_
Charge on standby STl::iiq[:,i!!!:V(.L:Hi:;I:(!!i
Use this feature to select whether this unit charges the
battery of the stationed iPod or not when this unit is in the
standby mode (see page 73).
Choices: AUTO, OFF
• Select "AU'I'O" to charge the battery of the stationed
iPod when this unit is turned on and in the standby
mode.
• Select "'OFF" to charge the battery of the stationed
iPod only when this unit is turned on.
1 O0 En