Page 1 BlackDiamond 8800 Series Switches Hardware Installation Guide Extreme Networks, Inc. 3585 Monroe Street Santa Clara, California 95051 (888) 257-3000 (408) 579-2800 http://www.extremenetworks.com Published: August 2008 Part number: 100284-00 Rev. 02...
Page 2 Powered by ExtremeXOS logo, and the Color Purple, among others, are trademarks or registered trademarks of Extreme Networks, Inc. or its subsidiaries in the United States and/or other countries. Adobe, Flash, and Macromedia are registered trademarks of Adobe Systems Incorporated in the U.S. and/or other countries.
Page 3: Table Of Contents
Introduction ...9 Conventions...9 Related Publications ...10 Part 1: About the BlackDiamond 8800 Series Switches Chapter 1: About the BlackDiamond 8800 Series Switches... 15 Overview of the BlackDiamond 8800 Series Switches ...15 Full-Duplex Support ...16 Management Ports ...16 External Compact Flash Memory Card ...16 BlackDiamond 8806 Switch Chassis...16...
Page 4 Port LEDs on Non-PoE Modules...39 Port LEDs on PoE Modules (G48P, G48Pe, and G48Tc or G48Te2 with S-POE Card) ...40 Chapter 3: Power Supply Units for BlackDiamond 8800 Series Switches... 41 Overview of BlackDiamond 8800 Series Power Supplies ...41 Extreme Networks 700/1200 W AC PSU ...42 LEDs...42...
Page 5 Rack-Mounting the BlackDiamond 8800 Series Chassis ...80 Grounding the BlackDiamond 8800 Series Chassis ...83 Initial Management Access ...85 Chapter 6: Installing Power Supply Units in the BlackDiamond 8800 Series Switches... 87 Safety ...87 PSU Compatibility...88 Combining Different AC PSU Models...88 Minimum Software Requirements ...89...
Page 6 Connecting Equipment to the Console Port ...114 Logging In for the First Time ...114 Part 3: Installing BlackDiamond Switch Accessories Chapter 8: Installing BlackDiamond 8800 Series Module Options ... 119 Installing an S-POE Daughter Card ...119 Removing an S-POE Card...121 Installing an Option Card in the MSM-48c...122...
Page 7 GBIC, SFP (Mini-GBIC), XENPAK, and XFP Regulatory Compliance ...160 Appendix B: Technical Specifications ... 167 BlackDiamond 8810 Switch...167 BlackDiamond 8806 Switch...170 Power Supplies for BlackDiamond 8800 Series Switches ...172 Connector Pinouts ...173 Index ... 1 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 8 Table of Contents BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 9: Preface
Extreme Networks BlackDiamond 8800 series switches. NOTE If the information in the installation note or release note shipped with your Extreme Networks switch differs from the information in this guide, follow the installation or release note. Conventions...
Page 10: Related Publications
● ● Summit Family Switches Hardware Installation Guide Extreme Networks Pluggable Interface Modules Installation Guide ● Documentation for Extreme Networks products is available from the Extreme Networks website at the following location: http://www.extremenetworks.com/services/documentation Alerts you to... Important features or instructions.
Page 11 You can select and download the following Extreme Networks documentation from the Documentation Overview page: Software User Guides ● Hardware User Guides ● You can find archived user guides for software at: http://www.extremenetworks.com/services/documentation/swuserguides.asp You can also find archived installation guides for hardware at: http://www.extremenetworks.com/services/documentation/hwuserguides.asp...
Page 12 Preface BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 13: Part 1: About The Blackdiamond 8800 Series Switches
About the BlackDiamond 8800 Series Switches...
Page 15: Chapter 1: About The Blackdiamond 8800 Series Switches
About the BlackDiamond 8800 Series Switches This chapter describes the Extreme Networks BlackDiamond 8800 series switches and includes the following sections: Overview of the BlackDiamond 8800 Series Switches on page 15 ● Full-Duplex Support on page 16 ● Management Ports on page 16 ●...
Page 16: Full-Duplex Support
Most ports on an Extreme Networks switch will auto-negotiate duplex operation in the default configuration. Gigabit Ethernet fiber ports and 10-Gigabit Ethernet ports operate only in full-duplex mode in accordance with technical standards.
Page 17 Ethernet MAC address of the switch ● Symbols of safety certification ● Access to the PSU/fan controllers ● Attachment point for optional chassis ground ● BlackDiamond 8800 Series Switches Hardware Installation Guide BlackDiamond 8806 Switch Chassis Fan tray I/O module slots I/O module slots EX_127...
Page 18: Blackdiamond 8810 Switch Chassis
Figure 3: Front of the BlackDiamond 8810 Chassis ESD wrist strap connector MSM module slot Power supplies Power cord connectors Figure 2 shows the rear panel of the BlackDiamond 8810 chassis. Fan tray I/O module slots I/O module slots ASP042 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 19 ● Ethernet MAC address of the switch ● Symbols of safety certification ● Access to the PSU/fan controllers ● Attachment point for optional chassis ground ● BlackDiamond 8800 Series Switches Hardware Installation Guide BlackDiamond 8810 Switch Chassis PSU/Fan controllers ASP044B...
Page 20 About the BlackDiamond 8800 Series Switches BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 21: Chapter 2: Blackdiamond 8800 Series Modules
Do not attempt to mix modules across Extreme Networks product lines. BlackDiamond 8800 series modules are for use only in a BlackDiamond 8806 or 8810 switch. When a BlackDiamond 8800 series switch is in use, ExtremeXOS software will not recognize a module from a different product line.
Page 22: Msm Physical Features
When a switch boots with a single MSM (regardless of the slot position), it is selected as the primary ● MSM. If a second MSM is added to the switch after it has been powered up, the added MSM becomes the backup MSM. MSMs that operate as backup MSMs can be inserted and removed without disrupting network services.
Page 23 Figure 7 shows the MSM-48c. Figure 7: MSM-48c The BlackDiamond 8800 series MSMs have the following features on the front panel: Console port—DB-9 serial port used to connect a terminal and perform local management. ● Management port—A 10/100 Mbps Ethernet management port used to connect an Ethernet cable ●...
Page 24: Msm Leds
The data port LEDs on the MSM-G8X operate the same as the port status LEDs on the G24X I/O module. I/O Modules The following series of I/O modules are available for the BlackDiamond 8800 series switches: BlackDiamond 8800 original series I/O modules (see ●...
Page 25: I/O Modules
When BlackDiamond 8800 I/O modules from different series (original series, a-series, c-series, and e-series) are installed in the same BlackDiamond 8800 series chassis, limitations on feature sets may occur. See the ExtremeXOS 12.0 Concepts Guide and the ExtremeXOS 12.0 Command Reference Guide for more information about these limitations.
Page 26: G24X I/O Module
Port status ● For information about the LEDs and their activity on the G24X module, see page 38. For information about the SFP modules, see the Extreme Networks Pluggable Interface Modules Installation Guide. 10G4X I/O Module The 10G4X I/O module...
Page 27: G48T I/O Module
The G48T I/O module has the following LEDs: Module status ● Module diagnostics ● Port status ● For information about the LEDs and their activity on the G48T I/O module, see page BlackDiamond 8800 Series Switches Hardware Installation Guide ports I/O Modules ASP037A “I/O Module LEDs” on...
Page 28: G48P I/O Module
● 10G4Xa I/O Module on page 31 ● 10G4Ca I/O Module on page 31 ● 11) has 48 autosensing 10/100/1000BASE-T ports that use standard RJ-45 10/100/1000BASE-T PoE ports BlackDiamond 8800 Series Switches Hardware Installation Guide ASP039A “I/O Module LEDs” on...
Page 29: G48Ta I/O Module
The G48Ta I/O module has the following LEDs: Module status ● Module diagnostics ● Port status ● For information about the LEDs and their activity on the G48Ta I/O module, see on page BlackDiamond 8800 Series Switches Hardware Installation Guide ports I/O Modules ASP048 “I/O Module LEDs”...
Page 30: G48Xa I/O Module
● For information about the LEDs and their activity on the G48Xa module, see page 38. For information about SFPs, see the Extreme Networks Pluggable Interface Modules Installation Guide. (Figure 13) has 48 1000BASE-X ports that use SPF fiber SFP connectors.
Page 31: 10G4Xa I/O Module
● For information about the LEDs and their activity on the 10G4Xa I/O module, see on page 38. For information about the XFP interfaces, see the Extreme Networks Pluggable Interface Modules Installation Guide. 10G4Ca I/O Module The 10G4Ca I/O module...
Page 32: Blackdiamond 8800 C-Series I/O Modules
● Inherit the properties of the default VLAN (for example, protocol type and VLANid) ● Operate in autonegotiation mode ● (Figure 16) has 48 autosensing 10/100/1000BASE-T ports that use standard 10/100/1000BASE-T ports BlackDiamond 8800 Series Switches Hardware Installation Guide ASP037A...
Page 33: 10G4Xc I/O Module
● Module diagnostics ● Port status ● For information about the LEDs and their activity on the 10G4Xc I/O module, see on page BlackDiamond 8800 Series Switches Hardware Installation Guide I/O Modules “I/O Module LEDs” 10G4Xc 10G4Xc 41614 BD_155 “I/O Module LEDs”...
Page 34: 10G8Xc I/O Module
Inherit the properties of the default VLAN (for example, protocol type and VLANid) ● Figure 18 has eight unpopulated XFP-based 10-gigabit Ethernet ports. This 10 Gbs ports Figure 19 has 24 unpopulated SFP-based 1-gigabit Ethernet ports. BlackDiamond 8800 Series Switches Hardware Installation Guide 10G8Xc 10G8Xc 41615 BD_155 “I/O Module LEDs” ASP049B...
Page 35: G48Xc I/O Module
Module diagnostics ● Port status ● For information about the LEDs and their activity on the G48Xc I/O module, see on page BlackDiamond 8800 Series Switches Hardware Installation Guide 1000BASE-X ports I/O Modules “I/O Module LEDs” ASP049A “I/O Module LEDs”...
Page 36: Blackdiamond 8800 E-Series I/O Modules
G48Te I/O Module The G48Te I/O module RJ-45 connectors. When an 8800 series switch is running in dual-MSM mode, this module will be oversubscribed 2:1. When the switch is running a single MSM, this module will be oversubscribed 4:1. Figure 21: G48Te I/O Module Module status LEDs The default configuration of the G48Te I/O module is as follows.
Page 37: G48Pe I/O Module
(PoE) to an attached device, using the same cable. The G48Pe I/O module supports the IEEE 802.3af PoE specification. When an 8800 series switch is running in dual-MSM mode, this module will be oversubscribed 2:1. When the switch is running a single MSM, this module will be oversubscribed 4:1.
Page 38: G48Te2 I/O Module
I/O Module LEDs This section describes the LEDs for the module, for the port, and for inline power delivery status for I/O modules in the BlackDiamond 8800 series of switches. NOTE Inline power delivery applies only to the ports on the G48P and G48Pe I/O modules or to a G48tc or G48Te2 I/O module with an installed S-POE card.
Page 39: Module Leds
Amber Diagnostic failure Port LEDs on Non-PoE Modules This section describes the port LEDs for non-PoE BlackDiamond 8800 series I/O modules and for port option cards installed in the MSM-8c. These include the following modules and option cards: G24X ●...
Page 40: Port Leds On Poe Modules (G48P, G48Pe, And G48Tc Or G48Te2 With S-Poe Card)
BlackDiamond 8800 Series Modules Port LEDs on PoE Modules (G48P, G48Pe, and G48Tc or G48Te2 with S-POE Card) This section describes the port LEDs for BlackDiamond 8800 series I/O modules that support PoE. These include the following modules: G48P ●...
Page 41: Chapter 3: Power Supply Units For Blackdiamond 8800 Series Switches
The chapter describes the power supply units used with the BlackDiamond 8800 series switches. Overview of BlackDiamond 8800 Series Power Supplies The BlackDiamond 8800 series switches can be powered by either AC or DC power supplies (PSUs). AC power supplies in the BlackDiamond 8800 series switches are fully fault tolerant and load-sharing in an N+1 configuration.
Page 42: Extreme Networks 700/1200 W Ac Psu
Figure 24: Extreme Networks 700/1200 W AC PSU The front panel on each Extreme Networks 700/1200 W AC PSU contains two cooling fans and a handle for insertion and removal of the unit. Airflow enters the front vents on the PSU and exits through the rear vents of the switch.
Page 43: Power Supply Cords
Power Supply Cords Extreme Networks 700/1200 W AC PSUs are shipped with both 110 V AC and 220 V AC power supply cords. The 110 V AC power supply cord allows a maximum DC output power of 700 W. The 220V AC power supply cord allows a maximum DC output power of 1200 W.
Page 44: Specifications
CAUTION The 700/1200 W AC PSU does not have a switch for turning the unit on and off. Remove the plug from the electrical outlet to disconnect power to the 700/1200 W AC PSU. Make sure that this connection is easily accessible.
Page 45: Extreme Networks 600/900 W Ac Psu
Figure 25: Extreme Networks 600/900 W AC PSU The front panel on each Extreme Networks 600/900 W AC PSU contains two cooling fans and a handle for insertion and removal of the unit. Airflow enters the front vents of the PSU and exits through the rear vents of the switch.
Page 46: Leds
Power Supply Cords Extreme Networks 600/900 W AC PSU(s) are shipped with both 110 V AC and 220 V AC power supply cords. The 110 V AC power supply cord allows for a maximum DC output power of 600 W. The 220V AC power supply cord allows for a maximum DC output power of 900 W.
Page 47: Fuse
Extreme Networks 600/900 W AC PSU for a complete replacement. WARNING! Field operators must not attempt to configure or replace fuses in Extreme Networks 600/900 W AC PSUs! In the event of failure, immediately return the defective Extreme Networks 600/900 W AC PSU for a complete replacement.
Page 48: Extreme Networks 1200 W Dc Psu
Extreme Networks does not recommended using the 1200 W DC PSU in combination with any Extreme Networks AC PSU in the same BlackDiamond 8800 series system. Extreme Networks recommends that DC and AC PSU units BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 49: Minimum Software Required
Field operators must not attempt to open the 1200 W DC PSU enclosure for any reason; the PSU does not contain user-serviceable parts. In the event of failure, return the defective 1200 W DC PSU to Extreme Networks for repair or replacement.
Page 50 Power Supply Units for BlackDiamond 8800 Series Switches BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 51 Installing BlackDiamond 8800 Series Switches...
Page 52 and Modules...
Page 53: Chapter 4: Site Preparation
● After examining your physical site and verifying that all environment requirements are met, evaluate and compare your existing cable plant with the requirements of the Extreme Networks equipment to determine if you need to install new cables. BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 54: Meeting Site Requirements
The address is NEMA; 1300 N. 17th Street; Rosslyn, Virginia 22209. Electronics Industries Alliance (EIA)—a trade association that develops technical standards, ● disseminates marketing data, and maintains contact with government agencies in matters relating to 172. http://www.nfpa.org BlackDiamond 8800 Series Switches Hardware Installation Guide “Power Supplies for http://www.nema.org...
Page 55: Wiring Closet Considerations
Temperature Extreme Networks equipment generates a significant amount of heat. It is essential that you provide a temperature-controlled environment for both performance and safety. Install the equipment only in a temperature- and humidity-controlled indoor area that is free of airborne materials that can conduct electricity.
Page 56: Humidity
To ensure proper airflow through a BlackDiamond switch, refer to the following recommendations when you install the switch: BlackDiamond 8800 series switches require a minimum of 1.5 inches (4 cm) around both the left and ● right sides of the chassis from any cabinet wall or other obstruction for proper airflow.
Page 57: Electrostatic Discharge
Use electrostatically safe equipment and the ESD-preventive wrist strap that is provided with your ● equipment. All switches have ESD-preventive wrist strap connectors and are shipped with an ESD- preventive wrist strap as shown in BlackDiamond 8800 Series Switches Hardware Installation Guide Airflow through fan tray ASP045...
Page 58: Rack Specifications And Recommendations
Use a rack grounding kit and a ground conductor that is carried back to earth or to another suitable building ground. All Extreme Networks switches are designed with mounting brackets that provide solid metal-to-metal connection to the rack. If you do not use equipment racks, you can attach wiring terminals directly to the mounting brackets for appropriate grounding.
Page 59: Space Requirements For The Rack
WARNING! The chassis does not have a switch for turning power to the unit on and off. For systems using an AC power supply, power to the chassis is disconnected by removing the wall plug from the electrical outlet. For systems using a DC SSI power supply, power to the chassis can be turned off by lifting the handle on the power supply or by de- energizing the circuit that feeds the power supply, which is usually accomplished by turning off a circuit breaker.
Page 60: Evaluating And Meeting Cable Requirements
● Radio Frequency Interference ● Cabling Standards Extreme Networks recommends using the Building Industry Consulting Service International (BICSI) Registered Communications Distribution Designer (RCDD), which is globally recognized as a standard in site planning and cabling. For information, go to: http://www.bicsi.org Cable Labeling and Record Keeping A reliable cable labeling system is essential when planning and installing a network.
Page 61: Installing Cable
Assign a unique block of sequential numbers to the group of cables that run between each pair of ● wiring closets. Assign a unique identification number to each distribution rack. ● Identify all wiring closets by labeling the front panel of your Extreme Networks equipment and ● other hardware. Keep accurate and current cable identification records. ●...
Page 62 Site Preparation Figure 31: Properly Installed and Bundled Cable Cable managers supporting and directing cables Proper bundling of cables Adequate slack, and bend radius SPG_008 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 63: Fiber Optic Cable
62.5/125 μm multimode fiber 10/125 μm single-mode fiber 10/125 μm single-mode fiber* 1000BASE-LX70 10/125 μm single-mode fiber (1550 nm optical window) BlackDiamond 8800 Series Switches Hardware Installation Guide Evaluating and Meeting Cable Requirements Figure 90∞ SPG_002 Mhz•Km Maximum Distance Rating (Meters) –...
Page 64: Rj-45 Connector Jackets
Category 5 and higher UTP cable 10BASE-T Category 3 and higher UTP cable Proprietary to Extreme Networks. Connections between two Extreme Networks 1000BASE-LX interfaces that use 10/125 μm single-mode fiber can use a maximum distance of 10,000 meters. RJ-45 Connector Jackets Use RJ-45 cable with connector jackets that are flush with the connector or that have connectors with a no-snag feature.
Page 65: Radio Frequency Interference
● Routing UTP cable near electrical transformers ● In areas or applications where these situations cannot be avoided, use fiber optic cabling or shielded twisted pair cabling (STP). BlackDiamond 8800 Series Switches Hardware Installation Guide Evaluating and Meeting Cable Requirements...
Page 66: Meeting Power Requirements
If a power source fails, it will affect only the switch power supply to which it is connected. If all switch power supplies are connected to a single power source, the entire switch is vulnerable to a power source failure.
Page 67: Ac Power Cable Requirements
An uninterruptible power supply (UPS) is a device that sits between a power supply (such as a wall outlet) and a device (such as a switch) to prevent outages, sags, surges, and bad harmonics from adversely affecting the performance of the device.
Page 68: Selecting A Ups
UPS Transition Time Transition time is the time that is necessary for the UPS to transfer from utility power to full-load battery power. For Extreme Networks products, a transition time of less than 20 milliseconds is required for optimum performance.
Page 69 You can access these standards at: http://www.ansi.org http://www.tiaonline.org BlackDiamond 8800 Series Switches Hardware Installation Guide Applicable Industry Standards...
Page 70 Site Preparation BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 71: Chapter 5: Installing The Blackdiamond 8800 Series Chassis
Correct lifting of the BlackDiamond 8800 series chassis requires two people. Before you lift a BlackDiamond 8800 series chassis, make sure the chassis is empty to prevent unnecessary weight. This will also prevent damage to the system components due to possible system chassis flex when lifting.
Page 72: Unpacking The Blackdiamond 8806 Chassis
Pull the prongs outward until the clip lock is released from the carton. Repeat these steps to release each remaining clip lock. Power cord retaining bracket BlackDiamond documentation pack with ESD-preventive wrist strap Figure 35). BlackDiamond 8800 Series Switches Hardware Installation Guide EX_110...
Page 73 Figure 36: Removing the Carton from the BlackDiamond 8806 Chassis Lift box chassis Open & remove 4 clip locks to free box 5 Unwrap the chassis. BlackDiamond 8800 Series Switches Hardware Installation Guide Unpacking the BlackDiamond 8806 Chassis Open lock EX_111A Figure 36).
Page 74 BlackDiamond documentation pack with ESD-preventive wrist strap ● NOTE Save all packaging, clip locks, and box pieces for future use in the event that the BlackDiamond 8806 chassis must be moved to another location or returned to Extreme Networks, Inc. Figure 37). EX_112...
Page 75: Unpacking The Blackdiamond 8810 Chassis
Do not proceed with unpacking the chassis if either the Tilt Watch indicator or the Shock Watch indicator displays a red warning state. Immediately contact Extreme Networks if a red condition occurs. 2 Open the flaps and remove the contents from the upper shipping carton (see...
Page 76 4 Lift the BlackDiamond 8810 shipping carton up and off the chassis (see 5 Remove all four restraining bolts that hold the BlackDiamond 8810 chassis to the shipping brackets on the shipping pallet (see ASP024 Figure Open lock Figure 41). BlackDiamond 8800 Series Switches Hardware Installation Guide EX_087B Figure 41).
Page 77 7 Carefully lift the BlackDiamond 8810 chassis off the shipping pallet and onto the floor as shown in Figure Figure 42: Correct Method for Lifting the BlackDiamond 8810 Chassis BlackDiamond 8800 Series Switches Hardware Installation Guide Unpacking the BlackDiamond 8810 Chassis ASP016B Figure 37).
Page 78: Pre-Installation Requirements
Save all packaging, clip locks, and box pieces for future use in the event that the BlackDiamond 8810 chassis must be moved to another location or returned to Extreme Networks, Inc. Pre-installation Requirements The following tools, equipment, and resources are required for installing the BlackDiamond 8800 series chassis: ESD-preventive wrist strap (provided) ●...
Page 79 4 On each side of the chassis, attach the appropriate mid-mount bracket using the eight screws provided in the kit (see Figure 43 Figure 43: Attaching the Mid-mount Brackets to the BlackDiamond 8806 Chassis Second mid-mount location BlackDiamond 8800 Series Switches Hardware Installation Guide Figure 44). Mid-mount bracket...
Page 80: Rack-Mounting The Blackdiamond 8800 Series Chassis
Rack-Mounting the BlackDiamond 8800 Series Chassis To mount the BlackDiamond 8800 series chassis in a rack: 1 Locate the 19-inch helper bracket that is shipped with the BlackDiamond 8800 series chassis. 2 Identify the rack location where the chassis will be installed.
Page 81 Figure 45: Mounting the 19-inch Helper Bracket onto the System Rack 4 Lift the back of the empty BlackDiamond 8800 series chassis onto the 19-inch helper bracket. 5 Slowly guide the chassis into the system rack until the mounting brackets are flush against the rack uprights.
Page 82 Installing the BlackDiamond 8800 Series Chassis Figure 46: Securing the BlackDiamond 8806 Chassis to a Rack EX_171A BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 83: Grounding The Blackdiamond 8800 Series Chassis
Grounding the BlackDiamond 8800 Series Chassis Although grounding the BlackDiamond 8800 series chassis is optional, it is recommended. A grounding point with integrated pem-nuts is provided on the back of the chassis.
Page 84 2 Strip 0.5-inch (1.2-cm) of insulation from the stranded copper wire cable. 3 Insert the stripped wire into the cable lug. (Figure 48 Figure 49). PSU / fan controllers EX_128A PSU/Fan controllers ASP044A BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 85: Initial Management Access
6 Connect the other end of the wire to a known reliable earth ground point at your site. Initial Management Access For instructions on accessing the switch for initial management setup, see “Initial Management Access” on page 114. BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 86 Installing the BlackDiamond 8800 Series Chassis BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 87: Chapter 6: Installing Power Supply Units In The Blackdiamond 8800 Series Switches
WARNING! Field operators must not attempt to open the PSU enclosure for any reason; the PSU does not contain user-serviceable parts. In the event of failure, return the defective PSU to Extreme Networks for repair or replacement. BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 88: Psu Compatibility
WARNING! Extreme Networks DC PSUs do not have switches for turning the unit on and off. Make sure that the DC circuit is de-energized before connecting or disconnecting the DC power cord at the DC power socket on an Extreme Networks DC PSU.
Page 89: Minimum Software Requirements
Extreme Networks does not recommended using the 1200 W DC PSU in combination with any Extreme Networks AC PSU in the same BlackDiamond 8800 series system. Extreme Networks recommends that DC and AC PSU units not be used together in the same BlackDiamond switch.
Page 90: Installing An Extreme Networks Ac Psu
The wire size must be a minimum of 16 AWG (1.0 mm ● WARNING! Be sure that the source outlet is properly grounded before plugging the AC power cord into the Extreme Networks AC PSU. Installing an Extreme Networks AC PSU...
Page 91: Required Tools And Equipment
● Installing the PSU CAUTION Make sure that the Extreme Networks AC PSU circuit is not overloaded. Use proper over-current protection, such as a circuit-breaker, to prevent over-current conditions. To install an Extreme Networks AC PSU: 1 Attach an ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacle on the top-left corner of the switch front panel.
Page 92: Removing Or Replacing An Extreme Networks Ac Psu
If necessary, remove the power cord retaining bracket as described in AC Power Cord Retaining Brackets.” b Connect the new AC power cord to the AC input on the front of the switch and to the wall outlet on the other end. Then re-install the power cord retaining bracket.
Page 93: Leds On The 700/1200 W Ac Psu
6 To install a replacement PSU, follow the steps under NOTE Leave the ESD strap permanently connected to the switch, so that the strap is always available when you need to handle ESD-sensitive components. LEDs on the 700/1200 W AC PSU The front panel of the Extreme Networks 700/1200 W AC PSU provides status LEDs.
Page 94: Installing An Extreme Networks 1200 W Dc Psu
Field operators must not attempt to open the 1200 W DC PSU enclosure for any reason; the PSU does not contain user-serviceable parts. In the event of failure, return the defective 1200 W DC PSU to Extreme Networks for repair or replacement.
Page 95: Installing A 1200 W Dc Psu
CAUTION Be sure that the grounding point on the back of the switch chassis is securely connected to earth ground. For information about grounding the switch, see 2 Verify that the 1200 W DC PSU is right side up, and press the yellow locking lever to the left while...
Page 96 Installing Power Supply Units in the BlackDiamond 8800 Series Switches Figure 53: Locking Handle on the 1200 W DC PSU Open Lock 3 Carefully slide the 1200 W DC PSU all the way into the power supply bay (see Be sure that the DC PSU is fully seated in the switch.
Page 97 For example, you should route the leftmost cable harness across the switch so that it exits through the right side of the grate. Route the rightmost cable harness across the switch so that it exits through the left side of the grate. The four middle cables can route in either direction.
Page 98: Removing A 1200 W Dc Psu
Always be sure that the 1200 W DC PSU does not have the input cabled connected at any time when the DC PSU is not installed in the switch. Do not remove the DC PSU from the switch before disconnecting the input DC cable from the PSU.
Page 99: Leds
NOTE Leave the ESD strap permanently connected to the switch, so that the strap is always available when you need to handle ESD-sensitive components. LEDs The front panel of the 1200 W DC PSU provides status LEDs. describes the LED activity.
Page 100 Installing Power Supply Units in the BlackDiamond 8800 Series Switches BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 101: Chapter 7: Installing Modules And Establishing Initial Management Access
CAUTION Do not attempt to mix modules across Extreme Networks product lines. BlackDiamond 8800 series modules are for use only in a BlackDiamond 8810 or 8806 switch. When a BlackDiamond switch is in use, ExtremeXOS software will not recognize a module from a different product line.
Page 102: Distinguishing An Msm From An I/O Module
Distinguishing an MSM from an I/O Module One quick way to distinguish a BlackDiamond 8800 series MSM from an I/O module is by the color of the release latch on each injector/ejector handle. Orange injector/ejector release latches indicate that the...
Page 103 Always place PC boards on a grounded surface before working on them. To install a module in a BlackDiamond 8800 series switch: 1 Attach the ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacle at the top left corner of the chassis.
Page 104 Figure 59: Injector/ejector Handles in the Latched Position CAUTION There are two styles of ejector/injector handles on the BlackDiamond 8800 series modules. Pay careful attention to the instructions in the next step. 8 Using a #2 Phillips screwdriver, lock the module into place in one of the following ways...
Page 105 NOTE Leave the ESD-preventive wrist strap permanently connected to the chassis so that the strap is always available when you need to handle ESD-sensitive components. BlackDiamond 8800 Series Switches Hardware Installation Guide Installing a BlackDiamond 8800 Series Module Figure 61), turn each captive...
Page 106: Making Network Interface Cable Connections
Installing Modules and Establishing Initial Management Access Making Network Interface Cable Connections Use the appropriate type of cable to connect the ports of your switch to another switch or router. Working carefully, one port at a time: 1 Verify that you have identified the correct cable for the port.
Page 107 63). Figure 63: Disconnecting a cable from a 10G4Ca port BD_158A 2 Make sure the latch is pulled into the fully disengaged position. 3 Pull the cable connector straight off the port connector. BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 108: Installing A Backup Msm
Depending on the size and complexity of your network, you should install and configure a backup MSM when network disruption will be minimal. You may need to reboot your switch after you use the synchronize command. Verifying the Module Installation After you install a module, verify that it is working correctly by checking the LEDs on the front panel of the module.
Page 109: Removing A Blackdiamond 8800 Series Module
Removing a BlackDiamond 8800 Series Module CAUTION There are two styles of ejector/injector handles on the BlackDiamond 8800 series modules. Pay careful attention to the instructions in step 2. This section describes how to remove modules from a BlackDiamond 8800 series switch. BlackDiamond modules are hot-swappable.
Page 110: Blank Front Panels
CAUTION All unoccupied slots in a BlackDiamond 8800 series switch must have blank front panels correctly installed to ensure conformance to FCC requirements as well as to maintain adequate airflow through the switch. You need the following tools and equipment to install or remove a blank front panel: ESD-preventive wrist strap ●...
Page 111: Installing A Blank Front Panel
Make sure that the EMI gasket is on the top of the panel and the stenciled part number is right side Figure 66: Blank Front Panels in a BlackDiamond 8800 Series Chassis 3 Use a #2 Phillips screwdriver to tighten the captive screws at each end of the blank front panel.
Page 112 3 Remove the blank front panel from the front of the BlackDiamond switch (see Figure 68). Figure 68: Removing a Blank Front Panel from a BlackDiamond 8800 series Switch ASP020 4 Install an I/O module or MSM in the open slot as described in “Installing a BlackDiamond 8800...
Page 113: Installing Or Removing An External Compact Flash Memory Card
2 Locate the compact flash slot on the MSM (see Figure 69: Typical Compact Flash Slot Location (BlackDiamond 8800 Series MSM) 3 Hold the memory card between your thumb and forefinger. The side with the ridge faces toward the bottom of the chassis.
Page 114: Initial Management Access
● Flow control—XON/XOFF ● The terminal or PC with terminal-emulation software that you connect to an Extreme Networks switch must be configured with these settings. This procedure is described in the documentation supplied with the terminal. Appropriate cables are available from your local supplier, or you can make your own. To ensure the electromagnetic compatibility of the unit, use only shielded serial cables.
Page 115 7 Save your configuration changes so that they will be in effect after the next system reboot by typing: save The configuration is saved to the configuration database of the MSM modules in the switch. NOTE For more information about saving configuration changes, see the ExtremeXOS 12.1 Concepts Guide.
Page 116 Installing Modules and Establishing Initial Management Access BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 117: Part 3: Installing Blackdiamond Switch Accessories
Installing BlackDiamond Switch Accessories...
Page 119: Chapter 8: Installing Blackdiamond 8800 Series Module Options
Installing an S-POE Daughter Card The S-POE daughter card adds PoE functionality to the ports on a G48Tc or G48Te2 I/O module. You must remove the I/O module from the BlackDiamond 8800 series switch before you install the S-POE card.
Page 120 72, carefully press the connectors into place. Make sure that all the connectors seat securely. Figure 71: Seating the S-POE Card on the I/O Module PoEcard_seat BlackDiamond 8800 Series Switches Hardware Installation Guide Daughter card connectors Figure 72). Following the sequence...
Page 121: Removing An S-Poe Card
Figure 72: Securing the S-POE Card to the I/O Module Tighten first Tighten second 7 Re-install the I/O module in the BlackDiamond 8800 series switch following the instructions in “Installing a BlackDiamond 8800 Series Module” on page Removing an S-POE Card To remove an S-POE card: 1 Attach the ESD-preventive wrist strap to your bare wrist.
Page 122: Installing An Option Card In The Msm-48C
5 At the edge of the module, rotate the hot-swap prevention latch up and hold it out of the way. Slide the option card the rest of the way into the slot “Removing a BlackDiamond 8800 Series (Figure 73) and remove the plate. ASP_051_cover (Figure 74). BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 123 8 Re-install the MSM-48c, following the instructions in Module” on page 102. Leave the ESD-preventive wrist strap permanently connected to the switch so that it is always available when you need to touch ESD-sensitive components. BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 124: Removing An Msm Option Card
1 Attach an ESD-preventive wrist strap to your bare wrist. If the metal end is not already connected, connect it to the ground receptacle at the top left corner of the chassis. 2 Remove the MSM from the BlackDiamond 8800 series switch as described in BlackDiamond 8800 Series Module” on page...
Page 125: Chapter 9: Blackdiamond Ac Power Cord Retaining Brackets
WARNING! These BlackDiamond switches do not have a switch for turning the power of the unit on and off. Power to the switch is disconnected by removing the wall plug from the electrical outlet. Always be sure that all plugs and electrical outlets are easily accessible.
Page 126 BlackDiamond AC Power Cord Retaining Brackets 3 Connect each AC power cord to a power outlet on the BlackDiamond 8810 switch as shown in Figure Figure 78: Connecting an AC Power Cord to the BlackDiamond 8810 Switch 4 Make sure that each AC power cord is firmly plugged into the power outlet as shown in...
Page 127: Disconnecting A Blackdiamond 8810 Ac Power Cord
#2 Phillips screwdriver. 4 Remove the BlackDiamond AC power cord retaining bracket from the front of the switch. 5 Remove the end of the AC power cord from the power outlet(s) on the front of the switch. NOTE Leave the ESD-preventive wrist strap permanently connected to the switch so that it is always available when you need to touch ESD-sensitive components.
Page 128: Blackdiamond 8806 Ac Power Cord Retainer Channel
2 Starting at the left, insert the plug of each AC power cord into the power connectors on the switch, and lift each installed power cord over the previous plug (see Verify that all installed AC power cords are firmly plugged into the power connectors.
Page 129 5 Starting from the left, lay the first four power cords into the channel (see Figure 85). 6 Lay the last two power cords on top of the bottom four cords (see Figure 85). BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 130: Removing The Blackdiamond 8806 Ac Power Cord Retainer Channel
From the left, lay first four power cords into channel bracket NOTE Leave the ESD-preventive wrist strap permanently connected to the switch, so that the strap is always available when you need to handle ESD-sensitive components. Removing the BlackDiamond 8806 AC Power Cord Retainer...
Page 131: Chapter 10: Blackdiamond Cable Management
Using the Cable Holders and Cable Clips When you use the cable holders and the cable clips, Extreme Networks recommends the following: Attach the cables to the holders by slipping the cable through the opening. ●...
Page 132: Connecting Cable Holders
Make sure that one locking tab at the joint is on top and the other is on the bottom. Figure 87: Connecting cable holders Interlocking cable holder and cable clips Side view Figure BlackDiamond 8800 Series Switches Hardware Installation Guide Cable clips Cable holder ENIN005A ENIN003...
Page 133: Connecting Cable Clips
1 Hold two clips next to each other with the split sides facing the same way (see Figure 89). 2 Slide the connecting grooves together (see Figure 89). Figure 89: Connecting cable clips ENIN001A BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 134 ENIN002A 4 Connect as many cable clips together as you need to manage your cable bundles. 5 To disconnect the cable clips, push on the bottom ring while holding the top ring steady. BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 135: Part 4: Blackdiamond Maintenance Procedures
BlackDiamond Maintenance Procedures BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 136 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 137: Chapter 11: Replacing Blackdiamond 8800 Series Chassis Components
Replacing BlackDiamond 8800 Series Chassis Components This chapter provides instructions for replacing components in the BlackDiamond 8800 series switches and includes the following sections: Replacing the Fan Tray on page 137 ● Replacing the PSU/Fan Controller on page 140 ●...
Page 138 5 Support the bottom of the fan tray with your free hand as you use the handle to slide the fan tray completely out from the fan tray slot. Fan Tray Captive Screws (x2) Fan Tray Handle ASP031A Fan tray captive screws (x2) Fan tray handle EX_114 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 139: Installing The Replacement Blackdiamond 8800 Series Fan Tray
2 Support the bottom of the fan tray with one hand as you lift the fan tray by the handle using the other hand. Align the spare fan tray with the fan tray slot on the switch, and then slide the fan tray...
Page 140: Replacing The Psu/Fan Controller
Leave the ESD-preventive wrist strap permanently connected to the switch so that it is always available when you need to touch ESD-sensitive components. Replacing the PSU/Fan Controller The BlackDiamond 8800 series switch has two PSU/fan controllers behind an access panel on the rear of the switch chassis. NOTE If your system is running ExtremeXOS version 11.2.1.3 or later, you can hot swap the PSU/fan controller unit.
Page 141: Removing The Psu/Fan Controller
Removing the PSU/Fan Controller To remove a PSU/fan controller from the BlackDiamond 8800 series switch: 1 Attach the ESD-preventive wrist strap to your wrist and connect the metal end to the ground receptacle on the front top-left corner of the switch.
Page 142 The PSU/fan controllers are visible in the controller recess. 5 Locate the four captive screws on the PSU/fan controller you are replacing (see Figure 97: Removing the PSU/Fan Controller (BlackDiamond 8806 Switch shown) PSU/Fan Controllers BlackDiamond 8800 Series Switches Hardware Installation Guide BD_169 Figure BD_170...
Page 143: Installing The Replacement Psu/Fan Controller
7 Pull equally on the upper and lower handles of the PSU/fan controller to disconnect the controller connector. Leave the ESD-preventive wrist strap permanently connected to the switch, so that the strap is always available when you need to handle ESD-sensitive components.
Page 144 Replacing BlackDiamond 8800 Series Chassis Components BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 145: Chapter 12: Repacking A Blackdiamond 8800 Series Chassis
CAUTION Before you lift a BlackDiamond 8800 series chassis, make sure the chassis is empty to prevent unnecessary weight. This will also prevent damage to the system components due to possible system chassis flex when lifting.
Page 146: Repacking The Blackdiamond 8810 Chassis
1 Attach the ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacle on the chassis front panel. 2 Remove all modules and power supplies from the chassis. Follow correct Extreme Networks procedures for removing components.
Page 147 Repacking the BlackDiamond 8810 Chassis Figure 98: Correct Method for Lifting the BlackDiamond 8810 Chassis ASP017A BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 148 Repeat these steps to insert each remaining clip lock. Figure 100: Clip Locks on the BlackDiamond 8810 Shipping Carton Squeeze prongs to unlock Clip lock Figure 99). Figure 100). Open lock EX_087B BlackDiamond 8800 Series Switches Hardware Installation Guide ASP016A...
Page 149 12 Close the top flaps on the shipping carton and seal them with packing tape. 13 Secure the BlackDiamond 8810 shipping carton with nylon straps (see Figure 102). Figure 102: BlackDiamond 8810 Shipping Carton with Nylon Straps ASP026 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 150: Repacking The Blackdiamond 8806 Chassis
7 Carefully lift the chassis off the helper bracket and lower it onto the foam cushion in the shipping carton base (see Figure Figure 103: Setting the BlackDiamond 8806 Chassis onto the Foam Cushion 103.) BlackDiamond 8800 Series Switches Hardware Installation Guide EX_129...
Page 151 Figure 105: Clip Locks on the BlackDiamond 8806 Chassis Shipping Carton Squeeze prongs to unlock Clip lock BlackDiamond 8800 Series Switches Hardware Installation Guide Repacking the BlackDiamond 8806 Chassis Insert & close 4 clip locks to secure box 105).
Page 152 107). NOTE Nylon straps are optional but are recommended by Extreme Networks for extra security during shipment. The installation of nylon straps requires a crimping tool. If you do not have nylon straps and a crimping tool available to secure the carton, the chassis can be shipped without the straps; however, it is critical that the clip locks be secure before shipment.
Page 153 Appendixes...
Page 155: Appendix A: Safety Information
Safety Information WARNING! Read the following safety information thoroughly before installing Extreme Networks products. Failure to follow this safety information can lead to personal injury or damage to the equipment. Only trained service personnel should perform service to Extreme Networks switches and their components.
Page 156: Maintenance Safety
WARNING! Extreme Networks DC PSUs do not have switches for turning the unit on and off. Make sure that the DC circuit is de-energized before connecting or disconnecting the DC power cord at the DC power socket on the Extreme Networks DC PSU.
Page 157: General Safety Precautions
Disconnect all power before removing the back panel of any Extreme Networks switch, unless ● otherwise instructed by a product specific maintenance procedure. Disconnect all power cords before working near power supplies, unless otherwise instructed by a ● product-specific maintenance procedure.
Page 158: Poe Devices
IEEE 802.3af. Selecting Power Supply Cords Extreme Networks provides power input cords shipped in the product box for use in the US and Canada. Power supply cords for use outside of the United States and Canada are typically provided separately by third-party distribution centers.
Page 159: Battery Replacement And Disposal
The power cord provided with the power supply, switch, or chassis is for use only with that ● specific product from Extreme Networks; it is not for use with any other product from Extreme Networks or any other vendors' equipment.
Page 160: Gbic, Sfp (Mini-Gbic), Xenpak, And Xfp Regulatory Compliance
Never look at the transmit LED/laser through a magnifying device while it is powered on. ● Never look directly at a fiber port on the switch or at the ends of a fiber cable when they are powered on. ●...
Page 161: Hinweise Zur Installation
Sicherheitshinweise Vor der Installation der Produkte von Extreme Networks sind die nachfolgenden Sicherheitshinweise aufmerksam zu lesen. Die Nichtbeachtung dieser Sicherheitshinweise kann zu Verletzungen oder Schäden an der Ausrüstung führen. Installation, Wartung und Ausbau eines Switch, einer Grundplatte oder einer seiner Komponenten dürfen nur von geschultem und qualifiziertem Servicepersonal durchgeführt werden! Geschulte und...
Page 162: Installation Von Netzteilen
Gleichspannungsquelle in Ihrem Gebäude angeschlossen werden. Extreme Networks 325 W AC Netzteile haben keinen An- Aus Schalter. Die Stromzufuhr zu einem Extreme Networks 325 W AC Netzteil wird durch das Ziehen des Netzkabels unterbrochen. Es ist sicherzustellen das diese Verbindung leicht zugänglich ist.
Page 163: Allgemeine Sicherheitsvorkehrungen
Networks entweder nur mit einem 110-VAC-Kabel oder mit einem 110-VAC-Kabel und einem 208/220- VAC-Kabel geliefert. Die von Extreme Networks gelieferten Stromkabel sind nur für den Einsatz in den Vereinigten Staaten und Kanada ausgelegt und zugelassen. Stromkabel für den Einsatz außerhalb der BlackDiamond 8800 Series Switches Hardware Installation Guide Fiber Optic Ports—Optical Safety...
Page 164 Das mit dem Netzteil, dem Switch oder der Grundplatte gelieferte Verbindungskabel ist nur ■ für den Einsatz mit dem spezifischen Produkt von Extreme Networks vorgesehen und darf nicht mit anderen Geräten von Extreme Networks oder anderen Anbietern verwendet werden. Nordamerika: Versorgungssteckdose, 15 A, NEMA 5-15 für 110-VAC-Netzteile und NEMA L6-15P ●...
Page 165 Hinweis: Die Bauvorschriften sind weltweit verschieden; Extreme Networks empfiehlt daher ausdrücklich, einen Elektroinstallateur zu beauftragen, um die sachgemäße Geräteerdung und Stromverteilung für Ihre spezifische Installation sicherzustellen. Austauschen und Entsorgen von Batterien Im Umgang mit Batterien sind folgende Hinweise zu beachten: Austauschen der Lithium-Batterie: Die in diesem Gerät enthaltenen Batterien können nicht vom...
Page 166 Safety Information BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 167: Appendix B: Technical Specifications
This appendix includes the following technical specifications: BlackDiamond 8810 Switch on page 167 ● BlackDiamond 8806 Switch on page 170 ● Power Supplies for BlackDiamond 8800 Series Switches on page 172 ● Connector Pinouts on page 173 ● BlackDiamond 8810 Switch...
Page 168 5 to 20 Hz @ 1.0 ASD w/–3 dB/oct. from 20 to 200 Hz 14 drops minimum on sides & corners @ 39.5" <22 lb (10 kg) modules @ 11.8" <110 lb (50 kg) chassis BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 169 Sound pressure in accordance Bystander sound pressure with NEBS GR-63 Issue 2 BlackDiamond 8800 Series Switches Hardware Installation Guide Normal: 70 dBA per ISO 7779 High: 75 dBA per ISO 7779 Normal: 7.2 belsA per ISO 7779 & ISO 9296 High: 7.7 belsA per ISO 7779 &...
Page 170: Blackdiamond 8806 Switch
IEC/EN 61000-4-4 Transient Burst, 1kV, Criteria A IEC/EN 61000-4-5 Surge, 2kV, 4kV, Criteria A IEC/EN 61000-4-6 Conducted Immunity, 0.15-80MHz, 10V/m unmod. RMS, Criteria A IEC/EN 61000-4-11 Power Dips & Interruptions, >30%, 25 periods, Criteria C BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 171 Declared sound power Sound pressure in accordance Bystander sound pressure with NEBS GR-63 Issue 2 BlackDiamond 8800 Series Switches Hardware Installation Guide (3 g), 11 ms, 60 shocks <50 kg 180 m/s (10 g), 6 ms, 600 shocks, modules >50 kg 100 m/s...
Page 172: Power Supplies For Blackdiamond 8800 Series Switches
Storage temperature: –40° C to 70° C Operating humidity: 10% to 90% relative humidity, non-condensing Operational shock: 30 m/s (3 g) BlackDiamond 8800 Series Switches Hardware Installation Guide ) copper stranded 158. , 60/50 Hz, 8 A max ) copper stranded (pre-approved cord set...
Page 173: Connector Pinouts
–48 V –60 V Maximum in-rush current: Not more than 80 A for 5 ms Input circuit protection: 50 A Wire harness provided by Extreme Networks with each power supply. Extreme Part# 4340-00028 Wire type: 8 AWG (10 mm minimum...
Page 174 9-pin to 9-pin (PC-AT) null-modem serial cable. Figure 109: PC-AT Serial Null-modem Cable Pinouts Switch Cable connector: 9-pin female Screen Shell Ground PC/Terminal Cable connector: 25-pin male/female Screen Ground 25pin PC/Terminal Cable connector: 25-pin male/female Screen Ground 25pin BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 175: Index
63 UTP cable, 61 BICSI standards, 60 BlackDiamond 8800 a-series I/O modules 10G4Ca, 31 BlackDiamond 8800 Series Switches Hardware Installation Guide 10G4Xa, 31 G48Ta, 29 G48Xa, 30 required software, 29 BlackDiamond 8800 e-series I/O modules...
Page 176 MSM-G8X module, 21 external memory card installing, 113 removing, 113 uses of, 16 fan tray installing, 139 removing, 137 fiber optic cable bend radius, 63 care, 63 connections, making, 106 first switch login, 114 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 177 G48Te2, 38 required software, 36 BlackDiamond 8800 original series 10G4X, 26 G24X, 26 G48P, 28 G48T, 27 PoE, 28 BlackDiamond 8800 Series Switches Hardware Installation Guide description, 25 G24XC, 34 G48Tc, 32 G48Xc, 35 hot-swapping, 109 injector/ejector handles, 104 installing, 103...
Page 178 S-10G1Xc option card, 23, 122 safety requirements, 155 See also environmental requirements securing rack to floor, 59 serial number BlackDiamond 8806 switch, 17 BlackDiamond 8810 switch, 19 service access to the rack, 59 BlackDiamond 8800 Series Switches Hardware Installation Guide...
Page 179 BlackDiamond 8810 AC power cord retaining bracket, 125 fan tray, BlackDiamond 8800 series switches, transition time, UPS, 68 BlackDiamond 8800 Series Switches Hardware Installation Guide troubleshooting external memory card, installing, 113 over-current conditions, 44, 47 power, turning off, 44, 46 RF interference, 65 uninterruptible power supply.
Page 180 Index BlackDiamond 8800 Series Switches Hardware Installation Guide...

This manual is also suitable for:

Blackdiamond g48te Blackdiamond g48xa Blackdiamond 8806 Blackdiamond 8810 Blackdiamond g48ta

Extreme Networks BlackDiamond 8800 Series Hardware Installation Manual

Preface

Part 1: about the Blackdiamond 8800 Series Switches

Chapter 1: About the Blackdiamond 8800 Series Switches

Chapter 2: Blackdiamond 8800 Series Modules

Chapter 3: Power Supply Units for Blackdiamond 8800 Series Switches

Chapter 4: Site Preparation

Chapter 5: Installing the Blackdiamond 8800 Series Chassis

Chapter 6: Installing Power Supply Units in the Blackdiamond 8800 Series Switches

Chapter 7: Installing Modules and Establishing Initial Management Access

Part 3: Installing Blackdiamond Switch Accessories

Chapter 8: Installing Blackdiamond 8800 Series Module Options

Chapter 9: Blackdiamond AC Power Cord Retaining Brackets

Chapter 10: Blackdiamond Cable Management

Part 4: Blackdiamond Maintenance Procedures

Chapter 11: Replacing Blackdiamond 8800 Series Chassis Components

Chapter 12: Repacking a Blackdiamond 8800 Series Chassis

Appendix A: Safety Information

Appendix B: Technical Specifications

Index

Quick Links

Related Manuals for Extreme Networks BlackDiamond 8800 Series

Summary of Contents for Extreme Networks BlackDiamond 8800 Series

This manual is also suitable for:

Table of Contents