About The Editor/Librarian Software; Adjusting The Display Contrast; Linking Effects; Switching Between Live Performance Sound And Direct Recording Sound - Zoom G7.1ut Operation Manual

Other Functions
About the editor/librarian
software
ZOOM CORPORATION makes an editor/
librarian software application available for
download on its web site.
To use the software, the computer must have a
MIDI interface, and a connection must be
established between the MIDI IN/MIDI OUT
connectors of the computer and the MIDI OUT/
MIDI IN connectors of the G7.1ut. The software
then makes it possible to store patch data of the
G7.1ut on the computer, edit the data, and copy
edited patch data back to the G7.1ut.
●
Web site of ZOOM CORPORATION
http://www.zoom.co.jp
Adjusting the display
contrast
If required, you can adjust the display contrast as
follows.
1.
In play mode, press the [AMP
SELECT/SYSTEM] key.
T h e A M P S E L E C T / S Y S T E M m e n u f o r
parameters that apply to all patches appears.
AMP Select 1/26 AMP Select 1/26
¡FRONT FRONT
2.
Turn the [TYPE] knob to bring up the
indication "Contrast" (display
contrast) on the display.
LCD LCD 2/26 2/26
¡Contrast:1 Contrast:1
50
3.
Turn parameter knob 1 to adjust the
contrast in the range from 1 – 3.
LCD LCD 2/26 2/26
¡Contrast:3 Contrast:3 é
4.
When the setting is complete, press
the [EXIT] key to exit the AMP
SELECT/SYSTEM menu.
The indication "Store...?" appears on the display,
to allow you to store the changes.
Store...? Store...?
Y[STORE] N[EXIT] Y[STORE] N[EXIT]
5.
Press the [STORE/SWAP] key to save
the changes.
The contrast setting is accepted, and the unit
returns to play mode.
In the above condition (while "Store...?" is
shown), only the [STORE/SWAP] key, [EXIT]
key, and [PAGE] key are active. By pressing the
[EXIT] key, you can abort the changes and return
to play mode without saving.
ZOOM G7.1ut

Linking Effects

The patches of the G7.1ut can be thought of as nine serially linked effect modules, as shown in the
illustration below. You can use all effect modules together or selectively set certain modules to off to use
just specific effect modules.
Pre-amp section
B Channel ZNR PRE-AMP
FD CLEAN
ZNR
COMP WAH/EFX1 ZNR PRE-AMP
A Channel
CLASS A
GATE
COMPRESSOR AUTO WAH FD CLEAN
ZNR
CLEAN
DIRTY
RACK AUTO VX CLEAN
NOISE
JC CLEAN
GATE
COMP RESONANCE
GATE
FILTER JC CLEAN
HW CLWAN
LIMITER
DIRTY
BOOSTER HW CLEAN
GATE
TREMOLO
For some effect modules, you can select an effect
type from several possible choices. For example,
the MOD/EFX2 module comprises CHORUS,
FLANGER, and other effect types from which
you can choose one.
The four-module series ZNR, PRE-AMP, EQ,
and CABINET functions as a virtual preamplifier
with two channels. The ZNR, PRE-AMP, and EQ
modules can have different settings for channels
A and B, allowing channel switching also within
the same patch.
Switching between live
performance sound and
direct recording sound
The PRE-AMP module of the G7.1ut comprises a
total of 36 effect types. In addition, each of these
effect types has two algorithms, one for live
playing and one for direct recording. This
amounts to having access to 72 effect types.
T h e r e s p e c t i v e a l g o r i t h m i s s e l e c t e d
automatically, depending on the status of the
CABINET module, as described below.
●
When CABINET module is off
The live performance algorithm is selected for
ZOOM G7.1ut
EQ
EQ
EQ CABINET MOD/EFX2 DELAY REVERB
EQ CABINET DELAY
CHORUS
PINGPONG-
STEREO
DELAY
CHORUS
ECHO
FLANGER
ANALOG
PITCH
DELAY
FILTER
t h e P R E - A M P m o d u l e . T h i s a l g o r i t h m
optimizes the sound for playing through a
guitar amp. When the G7.1ut is connected to a
guitar amp, this setting is recommended.
●
When CABINET module is on
The direct recording algorithm is selected for
t h e P R E - A M P m o d u l e . T h i s a l g o r i t h m
optimizes the sound for reproduction via a
system with flat response. When the G7.1ut is
connected to a recorder or hi-fi audio system,
this setting is recommended.
PRE-AMP EQ CABINET
Algorithm for On
direct recording
Off
Algorithm for
live performance
NOTE
When the CABINET module is off, the AMP
SELECT function for matching the G7.1ut to the
amplifier in use is also available. For details, see
the next page.
HALL
ROOM
SPRING
ARENA
51