Sending And Receiving Pedal/Switch/Key Operation Information Via Midi (Control Change) - Zoom G7.1ut Operation Manual

MIDI Usage Examples
SELECT/SYSTEM menu.
If any setting on the AMP SELECT/SYSTEM
menu has been changed, the indication "Store...?"
appears on the display, to allow you to store the
changes.
5.
Press the [STORE/SWAP] key to save
the changes.
The setting is accepted, and the unit returns to
play mode.
In the above condition (while "Store...?" is
shown), only the [STORE/SWAP], [EXIT], and
[PAGE] keys are active. By pressing the [EXIT]
key, you can abort the changes and return to play
mode without saving.
6.
To send and receive program change
(+ bank select) messages, connect
the G7.1ut and the other MIDI device
as follows.
■
Example for sending program change
(+ bank select) messages
(2) Program change (+ bank select)
message is sent
MIDI OUT MIDI IN
connector connector
(1) When a patch at the G7.1ut is switched...
■
Example for receiving program change
(+ bank select) messages
(1) When a program change (+ bank select)
message is received...
MIDI IN MIDI OUT
connector connector
(2) Patch at the G7.1ut is switched.
40
HINT
• When the program change mode of the G7.1ut
is set to "DIRECT", and the external MIDI device
sends only the MSB or LSB of the bank select
message, the most recently received complete
bank select instruction (initial values: MSB = 0,
LSB = 0) will be used.
• When the external MIDI device sends only the
program change message without bank select
MSB and LSB, the same as above applies,
namely the most recently received complete
bank select instruction (initial values: MSB = 0,
LSB = 0) will be used.
NOTE
When the external MIDI device sends only a bank
select message to the G7.1ut, no change occurs.
The next time the G7.1ut receives a program
change, the most recent bank select instruction
will be used.
■ Using mapping mode
In this mode, a program change map is used to
assign patches, allowing patches to be specified
by using program change messages only.
NOTE
Before carrying out the following steps, verify that
the send/receive MIDI channel setting of the
→
G7.1ut is as required ( p. 37), and that send/
receive of program change messages is enabled
( → p. 39).
1.
In play mode, press the [AMP
SELECT/SYSTEM] key.
AMP Select 1/26 AMP Select 1/26
¡FRONT FRONT
2.
Turn the [TYPE] knob to bring up the
"MIDI PCMODE" (program change
mode) parameter.
MIDI PCMODE 6/26 MIDI PCMODE 6/26
¡DIRECT DIRECT
ZOOM G7.1ut
3.
Turn parameter knob 1 to bring up the
indication "MAPPING".
Patches can now be specified using program
change messages according to the program
change map.
MIDI PCMODE 6/26 MIDI PCMODE 6/26
¡MAPPING MAPPING é
4.
Turn the [TYPE] knob to bring up the
"PC MAP" (program change map)
parameter.
Using this display, you can assign any patch of
the G7.1ut to a program change number from 0 –
127.
Program change number
PC MAP PC MAP ¡Prg: 0 Prg: 0
™Bnk:U0 Bnk:U0 £Pat:1 Pat:1
Group name/bank number Patch number
5.
To assign a patch to a program
change number, proceed as follows.
(1) Turn parameter knob 1 until the
program change number to use is
shown on the top line of the display.
Program change number
PC MAP PC MAP ¡Prg: 10 Prg: 10
™Bnk:U2 Bnk:U2 £Pat:3 Pat:3
Group name/bank number Patch number
(2) Use parameter knobs 2 and 3 to
select the group name/bank number
and patch number to assign to the
program change number.
ZOOM G7.1ut
MIDI Usage Examples
PC MAP PC MAP ¡Prg: 10 Prg: 10
™Bnk:A9 Bnk:A9é£ é£Pat:3 Pat:3
(3) Repeat these steps to for other
program change numbers.
6.
When the setting is complete, press
the [EXIT] key to exit the AMP
SELECT/SYSTEM menu.
The indication "Store...?" appears on the display,
to allow you to store the changes.
7.
Press the [STORE/SWAP] key to save
the changes.
The setting is accepted, and the unit returns to
play mode.
In the above condition (while "Store...?" is
shown), only the [STORE/SWAP], [EXIT], and
[PAGE] keys are active. By pressing the [EXIT]
key, you can abort the changes and return to play
mode without saving.
8.
To send and receive program change
messages, proceed as described in
step 6 of "Using direct mode" (→ p.
39).
Sending and receiving
pedal/switch/key operation
information via MIDI
(control change)
The G7.1ut allows sending and receiving control
change messages via MIDI. These messages
govern actions such as operating the built-in or an
external expression pedal and switching modules
or bypass/mute on and off with keys and foot
switches. Each action can be assigned its own
control change number (CC#).
41