Znr Module - Zoom G7.1ut Operation Manual

Effect Types and Parameters
Tremolo
This effect periodically varies the volume level.
PARM1 PARM2
Depth 0 – 100 Rate
0 – 50
Adjusts the modulation depth. Adjusts the modulation rate.
Phaser
This effect produces a swooshing sound.
PARM1 PARM2
Position
Befr, Aftr Rate
0 – 50
Selects the connection position
of the WAH/EFX1 module.
Available settings are "Befr" Adjusts the modulation rate.
(before pre-amp section) or
"Aftr" (after pre-amp section).
Ring Modulate
This effect produces a metallic ringing sound. Adjusting the "Freq" parameter results in a drastic change of sound
character.
PARM1 PARM2
Position
Befr, Aftr Frequency 1 – 50
Selects the connection position
of the WAH/EFX1 module.
Adjusts the modulation
Available settings are "Befr"
frequency.
(before pre-amp section) or
"Aftr" (after pre-amp section).
Slow Attack
This effect slows down the attack rate of the sound, resulting in a violin playing style sound.
PARM1 PARM2
Position
Time
Befr, Aftr 1 – 50
Selects the connection position
of the WAH/EFX1 module.
Available settings are "Befr" Adjusts the rise time.
(before pre-amp section) or
"Aftr" (after pre-amp section).
Pedal Vox
Simulation of the vintage Vox pedal wah.
Pedal Cry
Simulation of the vintage Crybaby pedal wah.
The above two effect types have the same parameters.
PARM1 PARM2
Position
Frequency
Befr, Aftr 1 – 50
Selects the connection position Adjusts the frequency that is
of the WAH/EFX1 module. emphasized. When the
Available settings are "Befr" expression pedal is not used,
(before pre-amp section) or the effect is similar to a half
"Aftr" (after pre-amp section). open pedal.
56
PARM3 PARM4
UP 0 – 9,
Wave DWN 0 – 9, Level 2 – 100
TRI 0 – 9
Controls the modulation
waveform. Available waveform
types are "UP" (rising
sawtooth), "DWN" (falling
Adjusts the signal level after
sawtooth), and "TRI"
passing the module.
(triangular). Higher numerical
values result in stronger
clipping, which emphasizes the
effect.
PARM3 PARM4
Color
1 – 4 Level 2 – 100
Adjusts the signal level after
Adjusts the sound color.
passing the module.
PARM3 PARM4
Balance 0 – 100 Level 2 – 100
Adjusts the balance between
Adjusts the signal level after
original sound and effect
passing the module.
sound.
PARM3 PARM4
Curve Level
0 – 10 2 – 100
Adjusts the rising volume Adjusts the signal level after
change curve. passing the module.
PARM3 PARM4
Dry Mix Level
0 – 10 2 – 100
Adjusts the level of the
Adjusts the signal level after
original sound mixed to the
passing the module.
effect sound.
ZOOM G7.1ut
P-Resonance
Pedal wah with a strong character.
PARM1 PARM2
Position
Befr, Aftr Frequency 1 – 50
Selects the connection position
of the WAH/EFX1 module.
Adjusts the modulation
Available settings are "Befr"
frequency.
(before pre-amp section) or
"Aftr" (after pre-amp section).
Octave
This effect adds a one-octave lower component to the original sound.
PARM1 PARM2
OctLevel 0 – 100 DryLevel 0 – 100
Adjusts the level of the one-
Adjusts the level of the
octave lower sound
original sound.
component.

ZNR module

This module serves for reducing noise during playing pauses. It offers a choice between
noise reduction and noise gate (muting during pauses).
ZNR (ZOOM NOISE REDUCTION)
ZOOM original noise reduction which reduces noise in playing pauses without affecting the overall tone.
Noise Gate
This is a noise gate which cuts off the sound during playing pauses.
Dirty Gate
This is a vintage type gate with special closing characteristics.
The above three effect types have the same parameter.
PARM1
Threshold
1 – 16
Adjusts the ZNR sensitivity.
For maximum noise reduction,
set the value as high as
possible without causing the
sound to decay unnaturally.
ZOOM G7.1ut
Effect Types and Parameters
PARM3 PARM4
Resonance 0 – 10 Level 2 – 100
Adjusts the resonance Adjusts the signal level after
intensity. passing the module.
PARM3 PARM4
Tone
0 – 10 Level 2 – 100
Adjusts the tonal quality of the Adjusts the signal level after
sound. passing the module.
57