Autopage RF-350 Installation & User Manual
Autopage RF-350 Installation & User Manual

Autopage RF-350 Installation & User Manual

Professional vehicle security system with keyless entry

Advertisement

RF-350
PROFESSIONAL VEHICLE SECURITY SYSTEM
WITH KEYLESS ENTRY
INSTALLATION & USERS MANUAL
(For Authorized Dealers Only)
Please register your product at
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY
1

Advertisement

Table of Contents
loading

Summary of Contents for Autopage RF-350

  • Page 1 RF-350 PROFESSIONAL VEHICLE SECURITY SYSTEM WITH KEYLESS ENTRY INSTALLATION & USERS MANUAL (For Authorized Dealers Only) Please register your product at www.autopageusa.com THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY...
  • Page 2: Wiring Diagram

    WIRING DIAGRAM...
  • Page 3: Door Lock Diagrams

    H1: MAIN 5 PIN WIRE HARNESS 1. Red / White Wire: Parking Light Relay input 2. White Wire: Parking Light Relay Output 3. Black Wire: Ground to Vehicle FRAME 4. Brown Wire: Positive output To 15A Fuse Siren 5. Red Wire: +12V To Constant Battery Source H2: 8 PIN MINI CONNECTOR WIRE HARNESS: 1.
  • Page 4 VACUUM OPERATED CENTRAL LOCKING Green Wire Door Switch +12V 3 Pin Plug To Compressor Alarm Blue Wire VACUUM OPERATED DOOR LOCKING SYSTEM: TYPICAL OF MERCEDES BENZ AND AUDI. Locate the wire under the driver's kick panel. Use the voltmeter connecting to ground, verify that you have the correct wire with the doors unlocked, the voltmeter will receive "12 volts".
  • Page 5: Programming

    2 STEP DOOR UNLOCK WIRE CONNECTION FOR POSITIVE SWITCHED DOOR LOCKS +12V OEM Door Master Lock Switch 8-Pin H2/8 Plug Gray Wire Unlock Lock From Alarm Existing Pos. Unlock Wire + 12V Existing Pos. Lock Wire H3/3 Green Wire Door Lock + 12V H3/1 Blue Wire...
  • Page 6 Note: If more than 4 transmitters are programmed, the system will only keep the last 4 transmitters and delete the others. ALARM FEATURE “A” PROGRAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 3 times and hold in on the 3 push.
  • Page 7 ALARM FEATURE “B” PROGRAMMING: Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. Push the Valet switch 5 times and hold in on the 5 push. When a long chirp is heard, release the valet switch. You are now in the Alarm feature ‘B’...
  • Page 8 ALARM FEATURE “C” PROGRAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 7 times and hold on the 7 push until Three chirps with a long chirp is heard then release the valet switch. You are now in the Alarm feature ‘C’...
  • Page 9: Transmitter Operation

    Operation Manual TRANSMITTER OPERATION: Transmitter System Function Remark Button Lock Doors & Arm System Panic function Press and Hold for 3 seconds Car Locator Under armed mode Arm and Delete The 2 Stage Shock Press twice within 3 seconds Sensor Silent Arming / Disarming Ignition in "off"...
  • Page 10 / hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed. 2. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time. PASSIVE DOOR LOCKING: The vehicle doors will automatically lock after passive arming cycle has been completed.
  • Page 11 ANTI CAR-JACKING: (OPTIONAL) If alarm option is installed. Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature “OFF”. This system is default setting Car-jacking “OFF”. 1. TRANSMITTER ACTIVATE THE CAR JACKING: Press and hold button on the transmitter for 1 second while the vehicle’s ignition is ON.
  • Page 12 TRUNK RELEASE. Press and hold button on transmitter for two seconds to remote control the trunk release or other electric devices. CAR LOCATOR Press the button on the transmitter to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, allowing you to easily locate your car. P.
  • Page 13 CHANGING THE BATTERY IN YOUR TRANSMITTERS XT-33: The XT-33 transmitter uses two (2) 3-volt lithium ion batteries (#CR2016) that are sandwiched together with the (+) side facing upward. To replace the battery, you will need to use a small flat blade screwdriver. Locate the small notch on the lower right side of the transmitter case next to the key ring.
  • Page 14 After one (1) year, the purchaser should ship the unit prepaid to Auto Page with a money order in the amount of $30.00 to cover shipping and handling charges. Note: The product needs to be registered online at time of www.autopageusa.com...
  • Page 15 You must register your product online at http://www.autopageusa.com receive any warranty service. Please go to the customer service tab and select product registration. It is the purchaser’s responsibility to register this product for any future warranty service. Warning: Some batteries may contain Perchlorate What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil.
  • Page 16 960 Knox Street Unit B, Torrance, CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com Technical Support: 800-945-2527 (For Authorized Dealers Only)

Table of Contents