Trouble-Shooting And Storage - Image 10.6 Owner's Manual

TROUBLE-SHOOTING AND STORAGE
Most treadmill problems can be solved by following the simple steps below, Rnd the symptom that
=al_plles,'and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-
736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central "rime (excluding holidays).
1. SYMPTOM: THE POWER DOES NOT TURN ON
• a. Make sure that the power cord Is plugged into a surge pmtedor, and that the surge protector is plugged into
a propedy grounded outleL (See HOW TO PLUG IN THE POWEI_ CORD on page 9.) Use only a UL-IIsted
surge protector, rated at 15 amps, with a 14-gauge cord of five feet or le_ in length.
b. After the power cord has been plugged In, make sure that the key Is fully Inseded into the console. Various
ind'zeators on the console should light.(See HOW TO TURN ON THE POWER on page 10.)
c. Check the circuit breaker located on the treadmill near the
power cord. If the switch protrudesas shown, the circuit break-
er has tdppod. To reset the circuit breaker, wait for f'we min-
utes and then press the switch back in.
d. Check the on/off switch located at the front of the treadmill
near the power cord. The switch must be in the "on"position.
Tripped _. Reset
"On=
Position
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the cimuit breaker located on the treadmill near the power cord. If the circuit breaker has tdpped (see
the drawing above), wait for rwe minutesand then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsed the key fully Into the console. Various indicators on the console
should light.
d. Check to make sure the on/off switch is in the "on"position. (See 1. d. above.)
e. If the treadmill still will not tun, please call our toll-free HELPLINE.
3. SYMPTOM: AN ERROR CODE (':'El," "E2," "E3," "E4," OR "ES") APPEARS ON THE CONSOLE
a. If error code "El" appears in the INCLINE display, a maffunotionmay have occurred in the incline system.
Remove the key, wa'_for ten seconds, and then reinsed the key. Ifthe error code appears again, call our toll-
tree HELPLINE. Do not operate the treadmilluntil the problem IScorrected.
b. Errorcode "E2" may appear in the SPEED display if the INCREASE SPEED or PROGRAM START button is
pressed and no movement of the walkingbelt is detected within seven seconds. Remove the key, wait for ten
seconds, and then reinsed the key. Make sure that you stand on the side railsof the treadmill each time you
start walking belt. If the error code appears again, call our toll-free HELPLINE. Do not operate the treadmilluntil
the problem is corrected.
c. Error code "E3" may appear in the SPEED display ifthe speed of the walking belt surges above the selected
speed setting. Remove the key, waitfor ten seconds, and then reinsed the key. If the error code appears again,
call our toll-free HELPLINE. Do not operate the treadmill until the problem is corrected.
2O
d. Error code "E4" may appear in the SPEED display if the walking belt is moving at a slow speed, and there is
excessivestress on the motor. Remove the key, wait for ten seconds, and then reinsed the key. If you weigh
over 200 pounds, it may be helpful to increase the incline of the treadmill. If the error code appealS again, call
our toll-free HELPLINE. Do net operate the treadmill until the problem is corrected.