Using The Smart Control Panel Tm - Craftsman 139.53939D Owner's Manual

Using the Wall.Mounted
Smart Control Panel
TM
SMART CONTROL PANEL
TM
Press the push button Motion Delecting
to open or close the Ught O n/Off
door. Press again to
reverse the door during Prog <Le_r>.
Hour.
the closing cycle or to stop
the door while it's opening.
This Smart Control
Panel
TM
contains a
motion detector that will , LI _tButton
automatically turn on the
light when it detects a person entering the garage.. This
feature can be easily turned off for extended work light
use,
Light Feature
Press the Light button to turn the opener light on
or off. It will not control the opener lights when the door is
in motion. If you turn it on and then activate the opener,
the light will remain on for 4-1/2 minutes.. Press again to
turn it off sooner° The 4-1/2 minute interval can be
changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows:
Press and hold the Lock button until the light blinks
(about 10 seconds). A single blink indicates that the timer
is reset to 1-1/2 minutes° Repeat the procedure and the
light will blink twice, resetting the timer to 2-1/2 minutes.
Repeat again for a 3-1/2 minute interval, etc., up to a
maximum of four blinks and 4-1/2 minutes.
When using the opener lights as working lights, we
recommend that you first disable the motion sensor.
Motion Detecting Light Feature: The opener light will
turn on automatically when a person walks in front of the
wall-mounted Smart Control PanelTM,This feature works
by detecting motion and body heat and may not work in
temperatures around 100 °F, 37 7C The opener light will
come on for 5 minutes, then shut off automatically if no
additional motion or heat differential is calculated.
To disable this feature, press the Automatic
Light On/Off button on the left side of the Smart
Control PaneF M.
We recommend that you disable the motion sensor when
using the opener lights as working lights. Otherwise, they
will turn off automatically if you are working beyond the
sensor's range.
Lock Feature
Designed to prevent operation of the door from
hand-held remote controls. However, the door will open
and close from the Smart Control Panel
TM,
the Outside
Keylock and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2
seconds. The push bar light will flash as long as the Lock
feature is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The Lock
feature will also turn off whenever the "learn" button
is activated.
•Push Bar
31
PROG <Learn> Feature
The Smart Control PaneF M is equipped with a PROG
<LEARN> button to assist in leaming remote controls to
the unit. Press the PROG <LEARN> button once to
initiate LEARN mode and the display will show 'Learn
Remote Control - Press Learn Button Again to Confirm'
Press the PROG <LEARN> button a second time and
the display will show 'Learn Mode - Press Remote
Control Button to Learn Remote.' Press the button of the
remote control to be learned and the worklight will blink
to confirm the remote control has been learned.
::yonlfzO Eo;tU:se
s,de buttons
to increment the hour or minute displayed on the LCD
display.
<LANG> Language Feature
Press this side button to toggle between the three
languages - English, Spanish, and French_
Degrees F/C Feature
Press this side button to toggle the temperature
units between Fahrenheit and Celsius.
Additional feature when used with the 3-Function
hand-held remote
To control the opener lights:
1. With the door closed, press and
hold a small remote button that
you want to control the light.
2. Press and hold the Light button
on the Smart Control PanePM.
3_While holding the Light button, press and hold the Lock
button on the Smart Control Panel
TM.
4. After the opener lights flash, release all buttons.