Zenith L26W56SA Installation And Operating Manual page 45

Detailed Descriptions of Installer Menu Items
000 -INSTALLER SEOUENCE
Specifies ent_ sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWERMANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The
POWERMANAGEfunction is for saving energy. If set to O, Power
Manage is Off. Settings range from 0 - 7, with i - 7 representing
the hours that the TV will remain On, unless there has been activity
from either the control panel or remote control.
002 - AC ON (AC Power Switchable)
If set to I, allows the L26W56XA to turn On just by applying AC
power. Pressing the On button is not necessary. This is desirable if
the L26WbCXA is plugged into a cable box or a power outlet
controlled by a wail switch. Use AD3 Left/Right arrow to choose 0 or
i where 0 is the default is Off, and I is On.
*Note: Z#set to 1 (On), the L26V/56XA does not respond to On/O[s
commands from either the remote or the display control panel, end
the SLEEPTIMER is aLso nonfunctionaL
003 - BAND/AFC (Band/Automatic Frequency Control)
SeLects the tuning band. There are 4 possible settings for this
option:
0 = Broadcast 1 = CATV
2 = HRC 3 = IRC
If some channels were not found by Auto Program, select the
appropriate Band setting here and add the channels using the
Channel List option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial channel
number when the L26W56XA is turned On. This feature is useful for
an in-house information channeL, since the L26W56XA would always
select that channel when it is turned On. Setting this to 255 causes
the Last channel viewed when the L26W56×A was turned Off, to be
the tuned to channel when the L26W56XA is turned On again.
255 = Last channel
126 Map to Channel 3.
i~125=ChX 0=Aux
127 Map to Channel 4.
*Note: Item 004 STRTCHANNELcannot be set to 0 if item 093 RJP
AVAILABLE is set to "1"
005 - CHAN LOCK (Channel Lock)
CHAN LOCKis ideal if the system must always be on the same
channeL. Changing channels with Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive if set to 0 (defauLt).
GeneraLLy, t his feature is used in connection with STARTCHANNEL
(InstaLLer item 004) where the start channel may, for example, be
set to 3 or 4. If the start channel is 3, then the L26W56XA will
remain Locked on Channel 3.
*Note: For Items 007, 008 and 009
For Legacy reasons, the scale used is 0 - 63. The PTCsoftware wiLL
translate this to the 0 - 100 scale used by the TV.
To translate a TV volume Level to the instaLLermenu value, use the
foLLowing formula:
InstaLLer VaLue = TV VaLuex 63
100
Enter only the whole number (disregard fractions).
007 - STRTVOLUME (Start Volume)
This function aLLowsthe InstaLLer to determine the initial volume
Levelsetting when the L26WbCXA is turned On. This feature is useful
for an in-house information channeL, since the L26W56XA would
always select that volume Level when it is turned On. The range of
values are 0 - 63, 255. If 255 is selected, the current volume Level
will be retained in memory when the L26W56XA is turned Off; at
turn On, the volume Level wiLLbe automatically set at the previous
or last LeveL.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume Level aLLowable with
the VOLUME (VOL) Up/Down controL. In this way, for example,
someone cannot set the volume too Low to hear. The value range is
from 0 to 63 -- change values with ADO Left!Right arrow. The
factory default is O, which provides the full range of volume controL,
if item 009 MAX VOLUMEis aLso set to 63. It may be best to set the
same value on every L26W56XA.
*Note: The minimum volume level cannot have a value setting higher
than the MAX VOLUME level (described below,).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume Level aLLowabLe with
the VOLUME (VOL) Up/Down controls. In this way, for example,
someone can not set the volume Level high enough to disturb
others.
(Continued on next page)
PAGE 45