Related Manuals for Autopage C3-RS-665
Summary of Contents for Autopage C3-RS-665
- Page 1 C3-RS-665 PROFESSIONAL REMOTE CAR STARTER & 2 CHANNEL SECURITY / ALARM SYSTEM With Two Way Data Port INSTALLATION MANUAL Compatible THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY...
-
Page 2: Table Of Contents
TABLE OF CONTENTS: HJKL INSTALLATION WARNINGS INSTALLATION DIAGRAM Wiring Diagram H7 16-Pin Wire Harness Wiring Description H1 Connector Wiring Description H2 Connector Wire Connector H3, H4, H6, H7 Connectors Wiring Description H7 Connector H3 Connector Valet Switch H5 Door Lock Connector H9 Serial Data Port connection RS-232 Remote Transmitter Programming Feature ‘A’... -
Page 3: Table Of Contents: Hjkl
INSTALLER WARNINGS This Remote Starter with Alarm and Keyless Entry System has been designed to be installed on fuel-injected vehicles with an automatic transmission ONLY. Never install this remote starter on a manual transmission vehicle. This system must be installed and wired through a safety switch so it will not start in any forward or reverse gear. -
Page 4: Installation Diagram
INSTALLATION DIAGRAM: RX-300A Violet : Starter Output FUSE Red : 12 Volt Input FUSE Red : 12 Volt Input Yellow. Ignition 1 Output Pink : Ignition 2 Output Brown ACC Output LED Indicator Shock Sensor H1 6 Pin Wht. ANT. C3-RS-665 Data H7 16 Pin White... -
Page 5: Wiring Diagram
WIRE DIAGRAM: #H1 6 PIN HEAVY GAUGE WIRE HARNESS Red: Remote Start Power 1 Red: Remote Start Power 2 Violet: Starter (+) Output Pink: Ignition 2 (+) Output Yellow: Ignition 1 (+) Output Brown: Acc/Heater (+) Output #H2 5 PIN WIRE HARNES S Red/White: Parking Light Relay Power Input White: Parking Light Relay Output Black: System Main Ground (-) -
Page 6: H7 16-Pin Wire Harness
#H7. 16 PIN MOLEX CONNECTOR: Blue Wire:(-) Zone 2 Negative Hood/Trunk trigger White / Violet Wire: (+) Brake Switch Shut Down Input Green Wire : Zone 3 (-) Negative Door Pin Trigger Violet Wire: Zone 3 (+) Positive Door Trigger White Wire: (-) 200mA Dome Light Control Output White / Black Wire: (-) Negative Hood Pin Safety Shut Down WIRING... - Page 7 installation method. In addition you will realize why the connection of the safety wire is required for all mechanical switch configurations. Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of the installing technician to test the remote start unit and assure that the vehicle can not start via RF control in any gear selection other than park or neutral.
-
Page 8: Wiring Description H2 Connector
turned “OFF”, the ignition wire should receive “0” voltage. The YELLOW wire must be connected. PINK Wire – Ignition 2 Output Some vehicles have [2] ignition wires that must be power. Connect the PINK wire to the ignition 2 wire from the ignition switch. The ignition wire should receive “12 volts”... -
Page 9: Wire Connector H3, H4, H6, H7 Connectors
damage to the alarm and parking relay will result. BLACK WIRE — SYSTEM GROUND – This is the main ground connection of the alarm module. Make this connection to a solid section of the vehicle frame. Do not connect this wire to any existing ground wires supplied by the factory wire loom, make the connection to the vehicle’s frame directly. -
Page 10: Wiring Description H7 Connector
ORANGE WIRE – (-) 500ma GROUNDED OUTPUT WHEN ARMED This wire will become grounded when the alarm is armed. The current capacity of this wire is 500mA. This output can control the starter disable. IN4003 Diode Violet wire H7/1 : ORANGE wire White wire Red wire to Starter... - Page 11 wire to terminal #87a of the relay. Connect the other side of the (#1) wire to terminal #30. 5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown). Matching Resistor VAT wire (#1) YELLOW wire To + 12 V VAT wire Ignition...
- Page 12 Forth Channel Output (-) (See Alarm Feature A- 6 Programming) Negative output provided for forth channel operation. PINK WIRE – (-) 200ma PROGRAMMING OUTPUT (See Alarm Feature C - 3 Programming) 2 STEPS UNLOCK OUTPUT (Factory Default Setting) — The 2 step unlock feature will work for the most fully electronic door lock circuit.
- Page 13 Fuse +12V Or Ground CHANNEL 2 Depending On System Requirements Gray Wire +12V Electric Device BLUE WIRE — GROUND INSTANT TRIGGER INPUT — This wire is the ground trigger input wire for hood/trunk pin switches. GREEN WIRE — NEGATIVE DOOR SWITCH SENSING INPUT — This wire is the ground trigger input wire for negative door pin switch.
- Page 14 gets +12volts. If the brake lights switch in the vehicle switches +12 volts to the brake light circuit, connect this wire to the output side of the brake switch. This will allow the remote start to shut down if an attempt is made to operate the vehicle without the key while running under the control of the remote start.
-
Page 15: H3 Connector Valet Switch
multi-coil ignition system, the system can learn individual coil wire. Individual coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the ignition coils itself, the back of the gauges, engine computers, and automatic transmission computers. -
Page 16: H5 Door Lock Connector
H5. 3 PIN DOOR LOCK CONNECTOR NEGATIVE TRIGGER DOOR LOCK SYSTEM Blue Wire Door Unlock Locking Master Green Wire Door Lock Switch To Exiting Door Lock Relay POSITIVE TRIGGER DOOR LOCK SYSTEM Blue Wire Door lock Locking Master Green Wire Door Unlock Switch + 12V To Exiting... - Page 17 2 STEP DOOR UNLOCK WIRE 5 WIRE ALTERNATING DOOR H7/12 : + 12V OEM Door Master Lock 6 - Pin Switch Plug Pink Wire From +12V Alarm Unlock Lock Green Wire Cut the Unlock Wire H5 : 3 Pin Cut the Existing Plug Lock Wire Alarm...
-
Page 18: H9 Serial Data Port Connection Rs-232
RS232 C I 3 SERIAL TWO-WAY DATA PORT CONNECTION: This connector is to be used for Serial Data communications with idatalink modules by Auto Page only! DO NOT CONNECT THIS TO ANY OTHER WIRING! This connector will transmit digital codes to operate all functions of Autopage data modules. -
Page 19: Feature 'A' Programming
2. Within 15 seconds, push the Valet switch 2 times. (Holding down on the 2nd push) until you hear a long chirp. The transmitter is ready to program. Program: 1. Press the button on the transmitter until the siren responds with a confirming chirp, the first transmitter is now programmed. -
Page 20: Feature 'B' Programming
Siren Horn All Confirmation Confirmation Confirmation Confirmation chirps on chirp on only chirp on only chirps off Lock/Arm & Lock/Arm Unlock/Disarm Confirmation Confirmation Chirp Only Chirps H7/13 White wire= 3rd H7/13 White H7/13 White Channel H7/13 White wire= wire= Factory wire= Horn Momentary Security Rearm... - Page 21 One Chirp / LED one Press Three Chirps / Four Chirps / pulse Two Chirps / Transmitter LED three LED four Factory LED two pulses Button pulses pulses Default Setting Parking light turn “on” for 30- Parking light turn Pathway second upon an “on”...
-
Page 22: Feature 'C' Programming
FEATURE “C” PROGRAMMING: 1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 7 times (holding in on the 7th push) until three chirps with a long chirp is heard then release the valet switch. You are now in the Start feature ‘C’... -
Page 23: Start Feature 'D' Programming
REMOTE START FEATURE PROGRAMMING: START FEATURE “D” PROGRAMMING: 1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 9 times (holding in on the 9TH push) until four chirps with a long chirp is heard then release the valet switch. You are now in the Start feature ‘D’... -
Page 24: Rpm Learning
this setting. 4. Once you complete step 3, you can program “RPM Learning Mode” as follows: RPM LEARNING: While the system is in Start Feature “D” programming mode, 1. Press and release the transmitter button once, [1] LED flash, [1] siren chirp indicating you are in features “RPM Learning mode”. -
Page 25: Voltage Check Type
VOLTAGE CHECKING TYPE: Enter Start Feature ‘D’ Programming Mode: 1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 9 times (holding in on the 9th push) until four chirps with a long chirp is heard then release the valet switch. You are now in the Start feature ‘D’... -
Page 26: Return To Factory Default
TIMER CHECKING TYPE: Enter Start Feature ‘D’ Programming Mode: 1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 9 times (holding in on the 9th push) until four chirps with a long chirp is heard then release the valet switch. You are now in the Start feature ‘D’... -
Page 27: Shutdown Diagnostics
3. Press the button on the transmitter together for 6 seconds. There will be a six confirmation chirps with 3 long chirps to confirm the system “Alarm Feature A, B Programming all returns to factory default setting. RETURN TO START FEATURE FACTORY DEFAULT SETTING: Press the button first, within 3 second, then press button... -
Page 28: Neutral Safety Switch Test
Caution!! The follow procedure must be performed after the installation of the Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury, property damage, or both. 1. - Page 29 connection of a safety wire from the remote start device to the vehicle PARK/NEUTRAL ECM input or the vehicle key in sensor. This connection will prevent remote start operation if the key is left in the ignition switch regardless of the gear selector position. PARK/NEUTRAL ECM INPUT: The Park/Neutral ECM input is the preferred method of installation.
- Page 30 WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available. NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down.
-
Page 31: Tech Line
H. Connect terminal 85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B. Note: A second 4003 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. - Page 32 (800) 945-2527 www.autopageusa.com...
- Page 33 960 Knox Street, Unit B Torrance CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com...