Autopage C3-RS-603 Installation Manual
  1. Manuals
  2. Brands
  3. Autopage Manuals
  4. Remote Starter
  5. C3-RS-603
  6. Installation manual

Autopage C3-RS-603 Installation Manual

Professional remote car starter with two way data port
Hide thumbs Also See for C3-RS-603:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
7/9/2008
C3-RS-603
PROFESSIONAL REMOTE CAR STARTER
With Two Way data Port
INSTALLATION MANUAL
Compatible
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY
RS-603 REV A.
1

Advertisement

Table of Contents
loading

Related Manuals for Autopage C3-RS-603

Summary of Contents for Autopage C3-RS-603

  • Page 1 7/9/2008 C3-RS-603 PROFESSIONAL REMOTE CAR STARTER With Two Way data Port INSTALLATION MANUAL Compatible THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY RS-603 REV A.

  • Page 2: Table Of Contents

    7/9/2008 TABLE OF CONTENTS Installer Warning ………………………………………. System Wiring Diagram ………………………………. H1 - Main 6 Pin Heavy Gauge Harness …………….. H2 – 6 Pin Harness …………………………………… H3 – 8 White Connector Harness …………………… Installation Factory Immobilizer Systems…………… H4 – 2 Pin Blue connector ……………………….…… H5 –...

  • Page 3: Installer Warning

    7/9/2008 INTRODUCTION INSTALLER WARNINGS This Remote Starter System is designed to be installed on fuel-injected vehicles with an automatic transmission ONLY. Never install this remote starter on a manual transmission vehicle. This system must be installed and wired through a safety switch so it will not start in any forward or reverse gear. Some automatic transmission vehicles [mainly older GM vehicles with a purple starter wire] have a mechanical-type neutral safety switch instead of electrical safety switch.

  • Page 4: System Wiring Diagram

    7/9/2008 INSTALLATION DIAGRAM RX-300A Violet : Starter Output FUSE Valet Red : 12 Volt Input Switch FUSE Red : 12 Volt Input Yellow. Ignition 1 Output Pink : Ignition 2 Output Brown ACC Output LED Indicator H1 6 Pin Wht. ANT.

  • Page 5: H1 - Main 6 Pin Heavy Gauge Harness

    7/9/2008 WIRING Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Tape wires that pass through holes on the firewall to prevent fraying. Watch out for sharp edges that may damage wires and cause a short circuit. CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete.

  • Page 6: H2 - 6 Pin Harness

    7/9/2008 H2: 5 PIN WIRE HARNESS: H2/1. RED/WHITE WIRE –PARKING LIGHT RELAY INPUT -- The RED/WHITE wire is the input to the flashing parking light relay. The connection of the RED/WHITE wire will determine the output polarity of the flashing parking light relay. If the vehicle you are working on has +12volt switched parking lights, you don’t need to connect this wire.
  • Page 7 7/9/2008 Hood Pin Switch To: White/Black Wire / Negative safety Diode To Vehicle Brake Switch BLACK/WHITE WIRE (-)Neutral Safety Switch Input H3/4 (-)Remote Start Enable Toggle Switch Input When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is disabled.

  • Page 8: Installation Factory Immobilizer Systems

    7/9/2008 This wire is designed to by-pass shock sensor module. This wire will supply an output at all times the remote start is operating plus an additional 3 seconds after the remote start unit turn off. (-) 200ma KEY SENSOR BY- PASS OUTPUT This output is for a Key sense wire by-pass that some Chrysler and Toyota vehicles us to activate the remote start.

  • Page 9: H4 - 2 Pin Blue Connector

    7/9/2008 5. Connect the previously s resistor from terminal #87 to the second(#2) wire (as shown). Matching Resistor VAT wire (#1) YELLOW wire To + 12 V VAT wire Ignition (#2) Switch VATS control Module H4. 2 PIN BLUE CONNECTOR FOR THE VALET SWITCH: Select a mounting location for the switch that is easily accessible to the driver of the vehicle.

  • Page 10: H7- Serial Data Port Connection Rs-232 Port

    7/9/2008 5-WIRE ALTERNATING DOOR LOCK +12V Green Wire Master Door Lock Switch Splice Cut the Existing 3 Pin Plug POSITIVE TRIGGER DOOR LOCK SYSTEM Unlock Wire To Alarm Splice Blue Wire Door lock +12V Locking Cut the Existing Master Green Wire Door Unlock Lock Wire Switch + 12V...

  • Page 11: Remote Transmitter Programming

    7/9/2008 PROGRAMMING A. PROGRAMMING TRANSMITTER: Note: This remote start system will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. PROGRAMMING THE REMOTE TRANSMITTER 1.

  • Page 12: Alarm Feature "Ii" Programming

    7/9/2008 FEATURE “ ” PROGRAMMING: 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in the ‘OFF’ position. 2 Push the Programming switch 2 times and hold it until the LED turns on and (*) two chirps with a long chirp is heard; then release the Programming switch.

  • Page 13: Rpm Learning

    7/9/2008 Exit : Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit. ** This will be used when connected to an Autopage CI3 compatible Two-way data module that will recognize the tach signal from the vehicle.

  • Page 14: Trouble Shooting

    7/9/2008 (-) Safety Shutdown input (Hood) 1. Close the hood. 2. Check H3/3 White/ Black wire connection. (+) Safety Shutdown input (Brake) or 3. Check H3/5 White/ Violet wire connection. Neutral Safety Switch input fail. 4. Move the Enable Toggle Switch to “ON” position.
  • Page 15 7/9/2008 than park or neutral, the mechanical function will not allow the key to be turned to the start position or be removed from the ignition cylinder. This configuration prevents mechanical operation while the vehicle is in gear but offers no consideration for electrical operation.

  • Page 16: Notes

    7/9/2008 Ignition Key In Sensor Drivers Door Pin Switch Switch Closes with Key In Ignition Cylinder Key In Chime Module + 12V + 12 V Connected to (-) Negative 1N4003 To Hood Pin Switch Safety Safety Input Wire Shut Down (H3/3) White/ Black (H3/3) To connect to the key in sensor as shown in method 1: A.
  • Page 17 7/9/2008 It is recommended to have a minimal digital service plan on your cell phone RS-603 REV A.
  • Page 18 7/9/2008 Your RS-603 is CI3 compatible and will open your world to the true power of two way communication. Complete tracking and full cell phone functionality can be added to your system. For more information please visit your local authorized Autopage dealer or go to www.autopageusa.com Winner of the BEST OF INNOVATIONS...
  • Page 19 7/9/2008 BLANK RS-603 REV A.
  • Page 20 7/9/2008 Auto Page, Inc. 960 Knox Unit #B Torrance, CA 90502 www.autopageusa.com RS-603 REV A.
  • Page 21 7/9/2008 Toll Free Tech Support Hotline: 800-945-2527 (For certified installation technicians only) RS-603 REV A.

Table of Contents