Specifications; Functional Description - Milwaukee 0612-20 Operator's Manual

3. Hold tools by insulated gripping sur-
faces when performing an operation
where the cutting tool may contact
hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed
metal parts of the tool "live" and shock
the operator.
4. Keep hands away from all cutting
edges and moving parts.
Symbology
Direct Current
Underwriters
Laboratories, Inc.,
United States and
Canada
No Load Revolutions
per Minute (RPM)
Capacities
High Speed
Flat Bit in Hole Saw
Cat. No. Steel
Wood in Wood
0602-20
3/8" 7/8" 1-1/4"
0612-20 1/2"
1" 1-3/4"

FUNCTIONAL DESCRIPTION

6
5
4
1. Speed selector
2. Tool holder
3. Trigger
4. Control switch
5. Keyless chuck
6. Torque selector collar
Specifi cations
Cat. No. Volts DC No Load RPM
0602-20 12 Low 0 - 400
High 0 - 1400
0612-20 14.4 Low 0 - 400
High 0 - 1400
Low Speed
Pathfi nder Auger Bit Screws (dia.)
Steel
Bit in Wood in Wood
3/8"
7/8" 1"
1/2"
1-1/4" 1-1/8"
1
3
4
Recharge only with the charger
specifi ed for the battery. For spe-
cifi c charging instructions, read the
operator's manual supplied with
your charger and battery.
Always lock trigger or remove
battery pack before changing or
removing accessories. Only use
accessories specifically recom-
mended for this tool. Others may
be hazardous.
Inserting Battery Pack onto Tool
Battery pack can be inserted onto the tool
in two ways.
1. For working in restricted spaces, insert
the battery pack from the front by sliding
battery pack onto the body of the tool.
1/4"
Insert the battery pack until the battery
1/4"
latches lock.
2. For optimum weight distribution and bal-
ance, insert the battery pack from the
back by sliding the battery pack onto the
body of the tool. Insert the battery pack
until the battery latches lock.
3. To remove the battery pack, press in
both battery latches and slide the battery
pack off of the tool.
Clip-Lok TM
The Clip-Lok system consists of three pieces;
the belt clip, the tool holder, and the bit
holder. The system is shipped assembled for
2
right-handed use. To change the assembly
for left-handed use:
1. Remove battery pack.
2. Remove screws holding the tool holder
and the bit holder.
3. Lift the holders at the narrow end and
pull the front tangs out of their slots.
4. Replace the pieces onto the desired
side by sliding the tangs into the slots.
Tighten the screws securely.
ASSEMBLY
Fig. 1
WARNING
Tool holder
Front tangs
WARNING
Attaching the Belt Clip
The belt clip can be mounted to tool belts,
bags, buckets, etc. To mount the belt clip:
1.
2.
3.
Using the Clip-Lok Tool Holder
1.
System
2.
Using the Clip-Lok Bit Holder
The bit holder holds two standard 1/4" hex
shank bits up to two inches long.
1.
2.
5
Bit holder
Clamp
release
Belt clip
Stud
Clamp
Pin
Tool release lever
Pull up the clamp release. The clamp
will pop out.
Slide the clamp over the tool belt, bag,
bucket, etc.
Press in the clamp to tighten.
To attach the tool to the belt clip, slide
the tool holder over the stud on the belt
clip until it is held in place by the protrud-
ing pin.
To release the tool from the belt clip,
grasp the tool handle, push down on
the tool release lever with your thumb,
and pull up on the tool.
Insert the bit by pressing it into the clip.
Remove the bit by lifting the tip of the
bit and pulling it out of the clip.