Milwaukee 0100-20 Operator's Manual
Heavy-duty close quarter drills
Hide thumbs
Also See for 0100-20:
- Operator's manual (26 pages) ,
- Service parts list (1 page) ,
- Operator's manual (24 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
HEAVY-DUTY CLOSE QUARTER DRILLS
EXTRA ROBUSTES PERCEUSES COUDÉES
MINITALADRO ANGULAR HEAVY-DUTY
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
Cat. No.
No de Cat.
0100-20
0202-20
0101-20
0299-20
0200-20
0300-20
0201-20
0302-20
Advertisement
Table of Contents
Related Manuals for Milwaukee 0100-20
Summary of Contents for Milwaukee 0100-20
- Page 1 OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. No de Cat. 0100-20 0202-20 0101-20 0299-20 0200-20 0300-20 0201-20 0302-20 HEAVY-DUTY CLOSE QUARTER DRILLS EXTRA ROBUSTES PERCEUSES COUDÉES MINITALADRO ANGULAR HEAVY-DUTY TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
-
Page 2: General Safety Rules - For All Power Tools
GENERAL SAFETY RULES — FOR ALL POWER TOOLS WARNING READ ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. -
Page 3: Specific Safety Rules
These carry important information. starting the power tool accidentally. If unreadable or missing, contact a 19. Store idle power tools out of the MILWAUKEE service facility for a free reach of children and do not allow replacement. persons unfamiliar with the power... -
Page 4: Extension Cords
If damaged, have it repaired by a objects, excessive heat and the greater the capacity of the cord. For ex- MILWAUKEE service facility before damp or wet areas. Double Insulated Tools: ample, a 14 gauge cord can carry a higher use. -
Page 5: Tool Assembly
Double sleeve Adjusting the Side Handle (Cat. No. 0201-20 Keyless 0200-20, 0202-20, 0299-20, 0300-20, Removing and Replacing Quik-Lok ® 0302-20) Cords (Cat. No. 0100-20, 0101-20, 0202- 20, 0302-20) Fig. 2 Single sleeve 0202-20 MILWAUKEE's exclusive Quik-Lok ® Cords Keyless 0302-20 provide instant fi... -
Page 6: Operation
Be sure the bit shank and chuck jaws are Be sure the bit shank and chuck jaws are OPERATION WARNING clean. Dirt particles may prevent the bit clean. Dirt particles may prevent the bit from lining up properly. from lining up properly. WARNING When using drill bits, insert the bit into When using drill bits, insert the bit into... - Page 7 Set the screw by slowing to a stop. Do not Bits Bits Saws Bits Saws Bits run screws down at excessive speeds. To 0100-20 0 - 2500 1-1/2" 1/4" remove screws, reverse the motor. 0101-20 0 - 4000 1-1/4" 1/4"...
-
Page 8: Maintenance
Subject to certain excep- tions, MILWAUKEE will repair or replace any part on a electric power tool which, after examina- tion, is determined by MILWAUKEE to be defective in material or workmanship for a period of...