Table of Contents
Advertisement
GAS HOOK-UP
NEVER
CONNECT
AN
UNREGULATED
GAS
SUPPLY
LINE
TO THE APPLIANCE.
USE
THE
REG ULA TOR/HOSE ASSEMBLY
SUPPLIED.
This is a liquid
propane
configured
grill. Do not
attempt to use a natural gas supply unless the grill
has been reconfigured
for natural gas use.
Total gas consumption
(per hour) of
this stainless
steel gas grill with all burners on "HI":
Main burner
33,000 Btu/hr.
Side burner
12,000 Btu/hr.
Total
45,000 Btu/hr.
The installation
of this appliance
must conform with
local codes or, in the absence of local codes, with
the national
fuel gas code, ANSI Z223. la-1988.
Installation
in Canada
must be in accordance
with
the
Standard
CAN/CGA-B149.1,
Natural
Gas
Installation
Code
or CAN/CGA-B149.2,
Propane
Installation
Code and local codes.
L.P. TANK REQUIREMENT
A dented or rusty L.P. tank may be hazardous
and
should be checked
by your L.P. supplier. Never use
a cylinder
with
a damaged
valve.
The
L.P. gas
cylinder
must
be
constructed
and
marked
in
accordance
with the
specifications
for
L.P. gas
cylinders
of the U.S. Department
of Transportation
(DOT)
or
the
National
Standard
of
Canada,
CAN/CSA-B339,
Cylinders,
Spheres and Tubes for
Transportation
of
Dangerous
Goods;
and
Commission,
as applicable.
Overfilling
prevention
device (OPD) shall be provided on cylinder & QCCt
connection
on the cylinder
valve, ANSI/CGA-V-1.
The cylinder
supply system
must be arrange
for
vapor
withdrawal.
The
cylinder
must
include
a
collar to protect the cylinder valve.
The cylinder
must be provided
with a shut off valve terminating
in an L.P. gas supply cylinder valve outlet specified,
as applicable,
for connection
type QCC1
in the
standard
for compressed
gas cylinder valve outlet
and inlet connection
ANSt/CGA-V-1.
Manifold
pressure:
(operating):
10" water column
(W.C.), (non-operating):
11.2" water column (W.C.).
L.P. GAS HOOK-UP
Ensure that the black plastic grommets
on the LP
cylinder valve are in place and that the hose does
not come into contact with the grease tray or the
grill head.
CONNECTION
Your stainless
steel
grill
is equipped
with
gas
supply orifices for use only with liquid propane gas.
It
is
also
equipped
with
a
high
capacity
hose/regulator
assembly
for
connection
to
a
standard
20lb. L.P. cylinder
(18-1/4" high, 12-1/4"
diameter).
To connect
the L.E gas supply
cylinder,
please
follow the steps below:
1.
Make sure tank valve is in its full off position
(turn clockwise
to stop)
2.
Check
tank
valve
to assure
it has proper
external male threads
(type 1 connection
per
ANSIZ21.81)
3.
Make sure all burner valves
are in their off
position.
4.
Inspect valve connections,
port, and regulator
assembly.
Look for any damage
or debris.
Remove any debris. Inspect hose for damage.
Never attempt to use damaged
or obstructed
equipment.
See your local L.P. gas dealer for
repair.
5.
When connecting
regulator assembly to the
valve, hand tighten the nut clockwise to a
complete stop. Do not use a wrench to
tighten. Use of a wrench may damage the
quick coupling nut and result in a hazardous
condition.
6.
Open the tank valve fully (counterclockwise).
Use a soapy water solution to check all
connections
for leaks before attempting
to
light the grill, see below. If a leak is found, turn
the tank valve off and do not use the grill until
a local L.E gas dealer can make repairs.
12
Advertisement
Table of Contents
