Drc Value; Dab Initialize; A0 Parental Lock; Network Setup - Denon TU-604CI - Multi-Zone Dual AM/FM Tuner Owner's Manual

ENGLISH
k DRC Value
Change DRC (Dynamic Range Control) value from broadcast
station setting.
The DRC (Dynamic Range Control) function lets you change the
dynamic range of the received sound depending on the content
of the broadcast so that the sound is easier to hear even when
the volume is low.
The dynamic range can be fine-adjusted in three steps.
[Display]
TUNER-6

DRC Value

[Selectable items] 1/2
OFF
l DAB Initialize
When the "DAB Initialize" procedure is performed, all the preset
memory settings for the stations and DABs are reset.
[Display]
TUNER-6

DAB Initialize

*DAB Initialize
Start:Enter
[Selectable items]
Start : Enter
: Starts initialization.
• A blinking "Initialize" is displayed during initialization.
• After the "Initialize" procedure is performed, the "Auto Tune"
procedure is conducted automatically.
• Once the "Auto Tune" procedure is completed, receivable channels
are played.
A0 Parental Lock
For any channel, set the radio reception limits.
[Display]
TUNER-5
Parental Lock
*Parental Lock
Lock setting
Enter Lock Code
[
*Lock setting
SR001:•Unlock–

Lock Setting
DAB
Set the channel radio reception limits.
ENTER
q Press
<SELECT/ENTER>
w Using
password (4 digits number) and press
e Select channel by pressing
the lock by pressing
[Selectable items]
Unlock
Lock
b When a Parental Locked channel is tuned, "Enter Lock Code : [
is displayed, then input the password.
1
• The default password is "0000".
DAB
• If the password is wrong, "Incorrect Code" is displayed. Input the
correct password.
• While listening to the channel being played, you can also set parental
lock (vpage 29).
Edit Lock Code
Change the password.
ENTER
q Press
w Select "Current Code" and press
e E nter the Current Code using
<SHIFT>
and
ENTER
r Press
t Select "New Code" and Enter a New Code using steps w to r
above.
y Select "Repeat Code" and Re-enter the New Code using steps w
to r above.
u Select "Execute" and press
• If the old password is incorrectly input, "Current Lock Code Incorrect"
SIRIUS
is displayed, and proceed again from step q.
• If the password input is 3 digits or less, "Enter 4 digits" is displayed,
and input again with a 4 digit password.
• If the new password is not correctly input, "New Lock Code do not
Match" is displayed and the password does not change.
]
.
[uio p] <SHIFT>
or and
ENTER
.
[ui] <FUNCTION d f
or
[o p]
.
: Do not lock selected channel(s).
: Lock selected channel(s).
.
ENTER
.
<SELECT/ENTER> [uio p]
or
.
to confirm.
[o] or <FUNCTION f>
.

Network Setup

Make network settings.
F Menu tree F
, input the
Main Setup
Network Setup
>, and set
a Network Information
s Network Setup
• If you are using a broadband router (DHCP function), there is no need
]"
to make the settings at "Setting the IP Address" and "Setting the
Proxy", since the DHCP function is set to "ON" in the TU-604CI's
default settings.
• If the TU-604CI is being used connected to a network without the
DHCP function, the network settings must be made. In this case,
some knowledge of networks is required. For details, consult a
network administrator.
• If you cannot connect to the Internet, recheck the connections and
settings (vpage 11).
• If you do not understand about Internet connection, contact your ISP
(Internet Service Provider) or the store from which you purchased
your computer.
• DHCP (Dynamic Host Configuration Protocol) :
These are systems by which the IP address and other network
settings are automatically set for the TU-604CI, computer, broadband
router and network devices.
• DNS (Domain Name System) :
This is a system for converting the domain names used when
browsing Internet sites (for example, "www.denon.jp") into the
IP addresses actually used for communications (for example,
"202.221.192.106").
a Network Information
Display network information.
[Items to be checked] DHCP= ON or OFF IP Address
MAC Address