Denon 2310CI - AVR AV Receiver Owner's Manual page 37

Setting items
Quick Select Name Rename Label : Change the display name of the selected "Quick Select"
Change the Quick Select setting.
ui
name. 1. Use to select the name of the Quick Select setting you want
to change, then press
2. Use o p to set the cursor to the character you want to change.
ui
3. Use to change the character, then press
• Up to 16 characters can be input.
• The input character type can be switched by pressing
display name is being changed.
• The types of characters that can be input are as shown below.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ˜
GNumbersH 0123456789 (Space)
4. Repeat steps 2 and 3 to change the display name.
Zone Rename ui
1. Use to select the zone name you want to change, then press
Rename the display names
.
of the different zones as
MAIN ZONE / ZONE2
desired.
o p
2. Use to set the cursor to the character you want to change.
3. Use ui to change the character, then press
• Up to 10 characters can be input.
• The input character type can be switched by pressing
display name is being changed.
• The types of characters that can be input are as shown below.
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GSymbolsH ! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ˜
GNumbersH 0123456789 (Space)
4. Repeat steps 2 and 3 to change the display name.
Remote control
operation buttons
Setting contents
.
.
.
Displaying the menu
:
: Moves the cursor (Up/Down/Left/Right)
Cancel the menu
Setting items
Trigger Out
Select the condition for
activating Trigger Out for
the input source, surround
mode, etc.
See "TRIGGER OUT jacks"
(vpage 18) for more
information on trigger out.
while the
Remote ID
Set when you operate
another DENON AV amplifier
with the remote control unit
of the AVR-2310. Match the
remote control unit you are
using with the remote ID of
the AVR-2310.
232C Port
Set when using an external
while the
controller or two-way remote
control connected to the RS-
232C terminal.
Dimmer
Adjust display brightness of
the receiver.
Setup Lock
Protect settings from
inadvertent change.
Making detailed settings (Manual Setup)
Setting contents
When Setting for Zone (MAIN ZONE / ZONE2)
n
Trigger out is activated through linkage to the power of the zone set to
"ON".
When Setting for Input Source
n
Activate trigger out when the input source set to "ON" is selected.
Valid for the zone set to "ON" with "When Setting for Zone" .
When Setting for Surround Mode
n
Activate trigger out when the surround mode set to "ON" is selected.
Valid when the "MAIN ZONE" set to "ON" with "When Setting
for Zone" is selected, and when the input source set to "ON" with
"When Setting for Input Source" is selected.
1 / 2 / 3 / 4
When using the AVR-2310 with only the included remote control unit
(RC-1117), use Remote ID "1" (default).
When using a separately sold remote control unit (RC-7000CI, etc.),
this function can be used. Match the ID setting of the remote control
unit and the receiver.
Serial Control : Set when using an external controller.
2Way Remote : Set when using a 2-way remote control unit.
When using a DENON two-way remote control (RC-7000CI or RC-
7001RCI, sold separately), set to "2Way Remote" .
NOTE
When setting to "2Way Remote" , you can not use the RS-232C connector
as an external controller.
Bright : Normal display brightness.
Dim : Reduced display brightness.
Dark : Very low display brightness.
OFF : Turns the display off.
Switching is also possible by pressing
ON : Turn protection on.
OFF : Turn protection off.
When "Setup Lock" is set to "ON" , the settings listed below can
no longer be changed. Also, "SETUP LOCKED!" is displayed if you
attempt to operate related settings.
・RESTORER ・Dynamic Volume
・MultEQ ・Channel Level
・Dynamic EQ ・Audio Delay
: Decision the setting : Return to previous menu
ENGLISH
on the main unit.