Denon 2310CI - AVR AV Receiver Owner's Manual page 35

Setting items
2CH DIRECT/STEREO Setting : Select the method for setting the speakers used in the 2-channel
Make speaker settings for 2- direct and stereo playback modes.
channel mode playback. • Basic : The settings at "Speaker Setup" (vpage 27) are applied.
• Custom : Make separate settings for 2-channel mode.
Front : Set the front speaker size.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
SW : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
SW Mode : Select low range signal to be reproduced by subwoofer.
• LFE : Add the low frequency signal of the channel for which the speaker
size is set to "Small" to the subwoofer signal and output it.
• LFE+Main : Add the low frequency signal of all channels to the
subwoofer signal and output it.
Crossover : Outputs at below set frequency, each speaker's bass signal
output from the subwoofer.
•
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz
/ 250Hz
Distance FL / Distance FR : Select the speaker you want to set, and set
the CH Level. Set the value that is closest to the measured distance.
0.00m ~ 18.00m (3.6m) / 0.0ft ~ 60.0ft (12.0ft)
•
CH Level FL/ CH Level FL FR : Select the speaker you want to set, and
set the CH Level. Adjust the level of each channel.
• –12.0dB ~ +12.0dB(0.0dB)
ON : Memorize settings. Most recently stored surround mode is
Auto Surround Mode
Make setting for memorizing automatically selected.
surround mode setting for
OFF : Do not memorize settings. Surround mode does not change
each input signal type.
according to input signal.
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals
listed below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.)
NOTE
When playing in the PURE DIRECT mode, the surround mode does not
change even if the input signal is changed.
Remote control
operation buttons
Setting contents
Displaying the menu
:
: Moves the cursor (Up/Down/Left/Right)
Cancel the menu
Setting items
EQ Customize Audyssey Byp. L/R / Audyssey Flat / Manual
Set so that unused equalizer
•
Used
settings are not displayed
• Not Used
when is used.
NOTE
• Set so that "Audyssey Byp. L/R" and "Audyssey Flat" settings can be
made when "Audyssey™ Auto Setup" is performed.
• Equalizer settings for which "Not Used" is set with the Quick Select
function cannot be stored and called out.
Making the ZONE2 settings (ZONE2 Setup)
Make settings for audio playback in a ZONE2 system.
"ZONE2 Setup" is displayed when ZONE2 is selected with "Amp Assign" (vpage 27).
Setting items
–12dB ~ +12dB (0dB)
Level Lch
Adjust the left channel output
level.
–12dB ~ +12dB (0dB)
Level Rch
Adjust the right channel
output level.
Volume Display Relative : The volume is displayed within the range of – – – dB (Minimum),
Set the ZONE2 volume
–80 dB ~ +18 dB.
display method.
Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit OFF : Do not set a maximum volume.
Make a setting for maximum
–20dB (61) / –10dB (71) / 0dB (81)
volume.
Power On Level Last : Use the memorized setting from the last session.
Defi ne the volume setting – – – : Always use the muting on condition when power is turned on.
that is active when the power
–80dB (1) ~ +18dB (99) : The volume is adjusted to the set level.
is turned on.
Mute Level Full : The sound is cut off entirely.
Set the amount of attenuation
–40dB : The sound is attenuated by 40 dB.
when muting is on.
–20dB : The sound is attenuated by 20 dB.
• The volume is displayed using the display method set at "Volume Display" (vpage 32).
• Set the main volume at "Volume Control" (vpage 32).
: Decision the setting
ENGLISH
Making detailed settings (Manual Setup)
Setting contents
Default settings are underlined.
Setting contents

: Return to previous menu