Table of Contents
Advertisement
a Connect the included Setup
Microphone
NOTE
• Do not disconnect the setup microphone until "Audyssey Auto
Setup" is completed.
• When using headphones, unplug the headphones before starting
"Audyssey Auto Setup" .
1
Check the speaker connections.
"
(
v
page 11
Connecting the Speakers
2
Turn on the power of the TV and subwoofer.
Set the TV's input to the AVR-2310.
3
Turn on the AVR-2310's power.
"
"
(
v
page 19
Turning the Power On
)
4
Connect the included calibrated setup microphone to
the SETUP MIC jack on the main unit.
Audyssey Auto Setup screen appears automatically.
Sound
receptor
5
Mount the setup microphone on a tripod or stand and
install it at the main listening position.
When installing the setup microphone, adjust its height so that
the section where the sound is received is at the height of the
ears during listening.
Setup
microphone
Remote control
operation buttons
NOTE
• Do not hold the microphone in your hand during measurements.
• Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
When using a subwoofer with adjustable gain and
crossover frequency
When using a subwoofer, make the following settings before starting
"Audyssey Auto Setup":
n
When using a subwoofer with a direct mode
"
)
Set the direct mode to "On" and disable the volume adjustment
and crossover frequency setting.
n
When using a subwoofer without a direct mode
Make the following settings:
• Volume
• Crossover frequency
• Low pass filter
• Standby mode
s Audyssey Auto Setup Preparations
STEP1 Preparation
Perform the following settings if adjustments, etc., are required for
the speaker environment you're using.
If you do not need to perform the following settings, or have already
completed them, select "Auto Setup Start" and then press
Proceed to " STEP2 ".
Displaying the menu
:
: Moves the cursor (Up/Down/Left/Right)
Cancel the menu
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey™ Auto Setup)
:"12 o'clock position"
:"Maximum/Highest Frequency"
:"Off"
:"Off"
around items indicate the default setting.
.
Changing the amplifier assignment (Amp Assign)
The signals output from the AVR-2310's SURR. BACK/AMP ASSIGN
speaker terminals can be switched to signals of the surround mode
being used.
1
Press
ui
to select "Amp Assign", then press
A U T O
A U D Y S S E Y
S T E P 1
P r e p a r a t i o n
C o n n e c t
t h e
a n d
p l a c e
i n g
t o
t h e
a t i o n s
i n
S e t
t h e
f o l l o w i n g
i t e m s
i f
n e s e s s a r y .
A m p
A s s i g n
C h a n n e l
A u t o
S e t u p
S e t
u s e
o f
2
Press
o
p
to select Amp Assign Mode, then press
.
Normal
: The sound of the surround back channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
ZONE2
: If the ZONE2 power is on, the sound of the
ZONE2 channel is output from the speakers
connected to the SURR. BACK/AMP ASSIGN
terminals.
Front A Bi-Amp
: The sound of the front A bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front B Bi-Amp
: The sound of the front B bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front Height
: T he sound of the front height channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
n
To cancel Audyssey Auto Setup
To cancel, press
then use
o p
to select "Yes".
: Decision the setting
: Return to previous menu
ENGLISH
.
S E T U P
A U T O
S E T U P
M u l t E Q
[ 1 / 6 ]
s p e a k e r s
t h e m
a c c o r d -
r e c o m m e n d a -
t h e
m a n u a l .
S e l e c t
S t a r t
E N T E R
E n t e r
R E T U R N
C a n c e l
s u r r o u n d
b a c k
c h .
f o r
y o u r
s y s t e m
2
Hide quick links:
Advertisement
Table of Contents
